Features

• 220 Grit
• Pre-cut to proper length for replacing abrasives on 31-250 wide drum sander
• Four per package

Features

• 23.75 inches x 11.75 inches x 2.0 inches
• Replacement three-pocket inner filter for 50-868 Air Cleaner
• Easy, tool-free installation for quick replacement
• Filters particles down to 1 micron for a cleaner, healthier work environment
• One filter per package

Features

• Two-year limited warranty on machines, parts, and accessories
• 230 volt, three phase, reversing motor for safe, efficient operation
• 3 spring-loaded, rubber feed rollers provide a positive grip on the workpiece
• Four speeds to match the application 13, 26, 36, and 72 feet per minute
• Adjusts vertically and horizontally for a variety of uses

Features

• 180 Grit
• Pre-cut to proper length for replacing abrasives on 31-250 wide drum sander
• Four per package

Features

• Replaces standard filter, no tools required for installation
• Cleans the air using static electricity for efficient filtration
• Washable and reusable for less operating cost
• Durable construction--lasts much longer than standard filters

Reviews (2)

Saves me MONEY!
Love this filter. Just Vac. it out & its ready to use! Beats blowing money on the throw aways.

Clean Air in a Dusty Woodturning Shop
I turn bowls and hollow forms on my lathe. During the sanding process, massive amounts of dust can be generated creating a large amount of airborne dust. The electrostatic filter in my Delta Air Cleaner traps this dust before it gets a chance to enter the air cleaner. It is easily removed from the unit and is a snap to clean. I've used disposable filters in the past which are either to thin or fill up with dust quickly and have to be discarded after only a short useful period. This new electrostatic filter solves the problem. I highly recommend it. ... Read more

Features

• Two-week satisfaction guarantee for consumer confidence
• Very stable for reliable support of larger stock
• Easy-to-install for less downtime
• Hardwood alder frame and laminated particleboard for durability and economy
• Fits any winged saw with a 27-inch table-depth

Features

• Fast, safe, easy to use
• Patented magnetic design holds knives in proper position for easy installation
• Allows faster and more accurate adjustment and replacement of blades

Reviews (1)

This jig is not always the best way to go
My joiner is an old 4 1/8 inch Craftsman. It runs pretty good but the knives are not easy to set. This jig seemed to be just the thing but there are two short comings I found:

1. When the jig is lined up with the knife at top dead center, the screws holding the knife in place are not accessible. So the jig has to be moved forward enough to get the knives to rotate just a bit. By this time, the knives are to high. With this set up, no amount of tweeking got both knives parallel and at the same height.

The way I tested whether the knives were parallel was to join a piece of scrape (3/4 x 3 1/2). This joined edge (3/4) was placed on the cast iron saw table and a square was used to see if the 3 1/2 side was 90 degrees to the table. I never had a test run where this was the case.

Another way I came up with was a ruler. The ruler was placed on the infeed side with the "6" on the very edge, side closest to the fence. Then the cutter was rotated until the steel blade hit the ruler. The contact point on the ruler was noted. In my case, this was about 7 1/16 on the ruler. Then the ruler was moved to the other end of the knive and the process was repeated. Most of the time I could not detect a difference so maybe my machine is the real problem.

2. The magnets were not strong enough to pull up the knives every time. Sure, the jig would stick to the cast iron table but the knives would often stay put. I used a spare rare earth magnet to pull the knives up to the jig magnets. Once in place, the knives would stay put most of the time. I ended up making another little tool with the magnet screwed to a scrap piece of wood. This was used to pull the knives up to the jig magnet.

So, I'll keep the tool as it came by way of UPS and sending it back would not be free. But I would be very careful about recommending the jig. ... Read more

Features

• Secures bowls and bases for turning without using mounting holes
• Adjustable to fit a variety of diameters
• Reversible jaws are stepped to fit a variety of projects
• Cast iron for durability and vibration resistance

Features

• Illuminates the workpiece for better visibility
• Flexible neck allows proper positioning for best lighting
• Simple bolt-on installation for quick set up
• Flexible gooseneck

Reviews (2)

Excellent lamp
Three of my Delta tools have this lamp installed. The 17-925 drill press, a 14" band saw (older version of the 28-475), and a (now discontinued) scroll saw. In each case, the lamp is just what the doctor ordered. The bracket easily attaches to many Delta tools, the goose-neck is about the right length and stays put when you move it into position, the switch works flawlessly with a nice click, and the shade completely covers the bulb. To keep the lamp shade cool, I use 30 or 50 watt mini flood bulbs, but standard bulbs up to 50 watts work OK. (Delta's similar 28-857 lamp has a longer goose-neck section, but has a "universal" bracket.)

This lamp isn't cheap, but it's well made.

Not great, but does the job
I owned this light for about a day or two. It came in the accessory kit for the Delta Band Saw Kit. This light is designed to mount permanently on a fixed location on the saw. Unfortunately the light's gooseneck is short and does not meet the lighting needs for band sawing. I took it back and replaced it with a magnetic base light. Much more versitile, and cheeper too. Now I am considering the 25-858 light for a uniguard. Seems like it might be just what the Dr. ordered since the mounting brackets will position the light right above the blade. Still costs about 2 x what it should, but it is Delta and you know how that goes. OEM products ususlly cost more, but they fit just right. ... Read more

Features

• Illuminates the workpiece for better visibility
• Flexible neck allows proper positioning for best lighting
• Magnetic base for easy attachment and removal
• Attaches to any steel or cast iron surface

Reviews (6)

Just about what you'd expect.
The first and foremost thing I checked was that it only takes a 40 watt bulb. Which puts just enough light to help and not quite enough if you have a bright shop. The other thing I noticed is that I went through my first light bulb very quick when I had it on the bandsaw. I think the vibration killed the bulb (get a light bulb for fans?), but since I moved it over to my drill press, the light bulb has lasted a bit longer. I haven't had any noticable issues with the magnet, it's strong enough to hold the lamp, but nothing else.

Other ways to use it.
I like this light for the fact that you can remove the base and use it to directly mount the unit on a homemade bracket or mounting hole on your tools. I found the magnet was not as strong as i would like, but by mounting it directly on my DP with a homemade bracket (connected to the bolts used for mounting the motor) it works great, not utterly perfect, but better than any other light of ths nature.

Over rated Underachiever
I ordered this magnetic lamp with the intention of using it with a newly purchased Jet Bandsaw. The magnet is strong enough to hold the base to the upper wheel cover, but only with the lamp hanging down. If the flexible arm is angled to the side or up, the base rotates or slips and will not hold its position. This product might work better if the surface to which it is attached is rough rather than the type of smooth painted surface one finds on the Jet saw. Save your money. This one is a dud.

Excellent Lamp
This is an excellent accessory that everyone should get. The magnet base is strong and doesn't move unless you want to move it.

Just the right size and flexibility of use
Well made, strong magnet, nice flexible gooseneck, just what I needed to shed some light on my bandsaw. It makes a big difference in work efficiency to have a focused light on your workpiece. Highly recommended. ... Read more

Features

• Fits Delta 43-505 Router/Shaper to accommodate 1/2-inch shaper cutters
• Allows a wider variety of operations to be performed, including panel raising
• Installs easily in arbor assembly for quick set up

Features

• 60 Grit
• Bulk roll, enough for 14 abrasive changes

Features

• 2-inch diameter for sanding larger curves and contours
• Aluminum oxide abrasive for long lasting, efficient sanding
• 150 grit for efficient sanding with finer finish
• 6 pack

Features

• 100 Grit
• Pre-cut to proper length for replacing abrasives on 31-250 wide drum sander
• Four per package

Features

• 6" diameter for small and medium face plate turnings
• 1"/8 left and right hand threads fit standard headstocks
• Pre-drilled holes for mounting the workpiece
• Cast iron for durability and vibration resistance

Reviews (1)

Great plate for turning.
I have used these plates for turning wood bowls in the past, and I have found nothing that I like better. I successfully turned an 18 inch oak bowl by mounting it onto this base plate. (I have to admit I was surprised at how beautiful it turned out, since it was my second major attempt at turning bowls)

I STRONGLY recommend purchasing this plate if you are planning on doing any serious bowl turning, since if you use a smaller plate the bowl may become detached when you apply pressure with the chisels, leaving you with a waste of time rather than a piece of art.

Good luck turning! ... Read more

Features

• Packaged in durable storage case/organizer
• Converts drill press for use as a spindle sander
• Includes 5 drums--1/2", 3/4", 1", 1-1/2", and 2" diameters
• Includes 2 sets each of 80 and 120 grit sanding sleeves
• Fits drills and drill presses with 1/4" and larger chucks

Reviews (4)

Best deal going!
Amazon has the best deal going with this set. The price is great, and this is yet another way to make your drill press useful...

A smooth attachment
This is a great way to turn your drill press into a drum sander for those small pieces that need sanding. It comes with every size you will need in your home workshop.

Handy little kit.
The sanding drum kit is easy to use and easy to store, every thing in one place. It's not a precision grinder but for the price it's going to be hard to beat.

Poor quality.
I purchased this kit at my local hardware store. When I tried to use the two largest sized drums with a drill press, I found that they were out of round - that is, they wobbled. The finish was unsatisfactory, so I returned the kit hoping to trade for another identical kit. I tested the new kit in the store and it had the same problem, but worse, so I just got a refund. ... Read more

Features

• Easy, bolt-together assembly
• Universal stand for use with a variety of machines
• Converts bench band saw to floor model unit, freeing up workbench space
• Steel construction for durability and stability
• Plastic feet for stability

Reviews (3)

Very sturdy universal stand
I was so pleased with how rigid the stand supported my Craftsman planer; I drove right back to the store and bought three more. Heavy-duty construction reduces vibration and the possibility of injury while working with large pieces of stock. I could support my truck on one of these. Assembly is a no brainer. You get what you pay for. (QUALITY) As for holes not matching up to some machines, a drill takes care of that.

Universal is right!
I purchased this stand for my belt/disc sander and it fits perfectly. I also discovered it is just right for my bench top drill press so I purchased another. Nice and sturdy with convenient storage underneath.

Wrong stand for 9" Band Saw
Directions provided with stand describe mounting 8" and 10" band saws. Front page includes

28-180 8" Band Saw 28-185 8" Band Saw 28-160 10" Band Saw

Does not include 28-150 9" Band Saw. Haven't found a set of holes that match up. Stand will not mount saw using 4 bolts as required. ... Read more

Features

• 1/2" diameter, for use with cope cutters
• Installs easily in place of standard spindle
• Tapered shaft is notched for a slip-free fit
• Fits Delta heavy-duty wood shapers 43-445, 43-455, and 43-460

Features

• Replacement pleated outer filter for 50-868 Air Cleaner
• Easy, tool-free installation for quick replacement
• Filters particles down to 5 microns before reaching the inner filter
• 2-pack

Reviews (1)

Great Product
This filter is excellent. It can be vaccumed or blown out several times without loosing it filtering ability. I do think that it is a tad expensive. ... Read more

Features

• Heavy gauge steel construction for strong support
• Pre-drilled holes for easy mounting
• Plastic feet for stability
• Fits Delta 32-325 and 32-326 Line Boring Machines