Features

• Provides proper clearance for use with dado sets
• Installs easily using existing table insert screws
• Fits Delta 36-600 table saw

Reviews (2)

A Perfect Fit...
I just bought a Delta TS300 10" table saw (use to be called a model 36-600, by the way) and started looking for dado sets and dado inserts. The Delta website is either perfectly useless or outright wrong when it comes to cataloging the correct accessories for each table saw. So I took my standard insert over to my local tool dealer and asked him to match it up with the correct dado insert. It took him all of 30 seconds to figure it out.
The 34-672 Dado Head Insert is the one to get for the following 10" Delta table saw models: TS300, 36-600, 34-740, and 34-670.
And don't be fooled into buying an 8" dado blade set just because the insert opening is big enough for it. If the motor is less than two horsepower (2 HP), then you should stick with a 6" dado blade set. Anything under 2 HP is considered "underpowered" for an 8" dado. Remember, you now have alot more metal spinning on that arbor, so don't burn out a $... motor just to impress your friends and neighbors.

Bad info on the Delta Web Site
I recently bought a Delta 36-650 10 inch table saw. After looking on the Delta web site, it listed this Dado Insert (34-672) as the correct one for this saw. Well, it was wrong. The correct dado insert for the 36-650 saw is the 34-264 (for 7-8 inch dados), there is a seperate part for 10 inch dado blades. So... I guess I'll be sending this one back... :( ... Read more

Features

• Installs quickly and easily on drill presses with 1-3/4" to 3-5/8" columns
• Stores bits and other tools in easy reach
• 11" diameter provides plenty of storage space
• Swivel mount allows easy positioning
• Predrilled holes to hold 3/32" to 1/2" drill bits

Reviews (1)

Every drill press should have one
What took me so long to get one of these? Construction of this swiveling tray is nice heavy molded plastic. Installation is a breeze. Now I can keep my chuck key, drill bits and parts and sundries within arm's reach. Reasonably priced. ... Read more

Features

• 5 pack
• 80 Grit
• 1" wide by 42" long
• Aluminum oxide abrasive
• Fits Delta 31-34- belt and disc sander and others requiring 1" by 42" belt

Features

• Adapts Delta Right-Tilt Unisaws for dust collection
• Allows you to maintain a cleaner, safer work environment
• Installs easily over opening under motor cover for quick set up
• Outlet fits 5-inch dust collector hose for efficient chip collection

Reviews (4)

Dust Collector Review
Overpriced in light of what you get (or don't get). They need to include the 5" to 4" adaptor (to get it down to the size most people use) and the correct screws to atach it. Otherwise it works fine. It keeps the dust to a minimum. I purchased a standard 5" to 4" heating vent adaptor at Home Depot and pop riveted it on so it would stay put. Extra cost and work that should not have happened if Delta had designed it correctly in the first place.

Not the right one to get for most users
Unless you have industrial-type 5" dust collector lines, get the Model 50-355, also sold here, instead. In spite of what it says on the 50-355 page, it works fine for both left-tilt and right-tilt Unisaws. The 4" port on the 50-355 is also the standard size for home shop dust collection systems.

Works great
I don't agree with the other person who rated it poor. Although it is very expensive for this little piece of sheet metal, prices are similar for air ducts you buy at the hardware store. The other person that rated it was right about not including the bolts that are needed though, which is poor on Delta's part. Otherwise it would have gotten 5 stars. I don't have any gaps with it on my Platinum Edition Unisaw, and it does a great job at getting rid of the dust on the ramp. I check every once in a while, and only get a little bit of piling up in the lower corners, next to the hole. This is far better than my old way of jamming the dust collector hose into the opening and just getting some of the dust, plus this connector gives the DC better suction. Since there is nothing else that fits the opening to this saw besides a cheap plastic option that works very poorly, this is your best bet to properly remove dust. I would recommend it.

lot of money for a bit of sheet metal
I must say that I was somewhat disappointed in this item. It is made out of cheap galvanized sheet metal, and looks to be worth about a quarter of what Delta is charging for it. Worse still, it does not fit my Special Edition Unisaw all that well -- there are significant gaps at the sides of the piece, and the bottom of the connector doesn't fit snugly against the dust ramp on the Unisaw. As a final indignity, they include the wrong type of screws to attach it to the saw. (I had to go buy two hex head bolts, washers, and nuts at the local hardware store in order to attach it.)

I kept mine, because I do so much work with my Unisaw that I really need to attach my dust collector to it, but Delta definitely needs to go back to the drawing board on this one. ... Read more

Features

• 100 Grit
• Bulk roll, enough for 14 abrasive changes

Features

• Converts drill press into accurate mortising machine
• Includes chisel holder, base, fence, and hold down bracket required to convert a drill press for mortising
• Allows the drilling of square and rectangular holes (mortises) for creating strong woodworking joints
• Requires the purchase of chisel and bits sets models 17-908, 17-909, 17-910, or 17-911\

Reviews (1)

Sorry Delta...
Nothing personal,but Delta dropped the ball on this one.
It will make a true mortise cut,but adjusting the chisel with the auger bit is a lot a work.I purchased this tool hoping to save some work.Tends to overheat.I'm a casual user of this tool.The Idea is wonderful,but needs some re-engineering. ... Read more

Features

• Replacement pleated outer filter for Delta 50-870 Air Cleaner
• Easy, tool-free installation for quick replacement
• Filters particles down to 5 microns in size
• Two filters per package

Features

• Fits Delta mortising attachments and mortising machine
• Drills 1/2" square holes for making mortise and tenon joints
• Center drill bit removes material, hollow chisel squares off the sides
• Two-piece design for easy re-sharpening
• High quality steel for durabilty and sharpness

Features

• Micron replacement dust collection bag
• Fits AP400 dust collection system

Features

• Fits Delta 31-460 Belt and Disc Sander and others requiring a 4-by-36-inch belt
• Aluminum oxide abrasive for long lasting, efficient sanding
• 60 grit for aggressive stock removal
• 1 pack

Features

• Adapts Delta 31-280 for use with sanding accessories for greater versatility
• For use with pneumatic sanding drums for sanding contour work

Features

• Drills 5/16" square holes for making mortise and tenon joints
• Center drill bit removes material, hollow chisel squares off the sides
• Two-piece design for easy re-sharpening
• Fits Delta mortising attachments and mortising machine

Features

• Charcoal filter for model 50-868
• Removes smoke, fumes and odors for a more comfortable work environment
• Easy, tool-free installation for quick replacement
• One filter per package

Reviews (1)

What was I thinking!
The concept of a charcoal filter clearing the air while using solvents sounds nice, but in practice it is ineffective and expensive. I used mine while working with contact cement and now the thing smells like contact cement. I suspect it is saturated, and without any way to purge it, is no longer any good. Additionally, while working I was much closer to the contact cement than was the filter, so whatever got to the filter had to pass by me first. Well, I also wore a charcoal filter mask and I think that is the way to go. You only filter what you breath and the filter is between the solvent and you--a much cheaper and effective solution. I would put my money there not in this device. ... Read more

Features

• 2 pack
• 120 Grit
• 5" diameter
• Aluminum oxide abrasive
• Fits Delta 31-080 belt and disc sander and others requiring 5" self-adhesive disc

Features

• Installs quickly in existing drill press table slots
• 2-1/2" x 2" jaw opening clamps small to medium stock
• Holds material securely for safer, more accurate drilling
• Squeeze-lock clamping mechanism for quick clamping
• Adjusts easily with knurled knob on handle

Reviews (1)

Poor quality product
Looks like and feels like a cheap tool. Flimsy. Nothing like any Delta product I've ever seen. ... Read more

Features

• 1" wide x 30" long
• Fits Delta 31-050 and 31-080 sanders
• 320 grit

Features

• Supports large, long, and wide workpieces up to 200 pounds
• 2-1/2" x 17-1/2" ball bearing roller keeps materials moving in a straight line
• Cast-iron base for stability
• Adjusts from 26-1/4 to 43-1/2 inches high to match a variety of table heights

Features

• Fits Delta machines with 3/8-by-3/4-inch miter slots for angled cutting and shaping
• 120-degree swing with positive stops at 45 and 90 degrees for quick set up
• Provides more accurate straight and angled cut off work
• Accepts optional clamp kit 34-568 (sold separately) for more accurate cutting

Reviews (2)

SOLID AS A ROCK
This gauge is easy to set up and easy to position. You may have to make a few adjustments to true it all up but, when your finished this thing is rock solid.The T-track system allows you to extend your gauge well beyond the edge of your table for larger pieces.Made with a combination of aluminum and steel this thing is built to last.I do recommend coating the bar with a dri-cote type product if rust is a concern. Now get out there and cut some miters.

Miter gauge
This miter gauge has stops which you can be set and will cut exactly on that stop position every time without any slippage. It looks simple but is a very good and precise gauge. ... Read more

Features

• 1" wide x 30" long
• Fits Delta 31-050 and 31-080 sanders
• 100 grit