Features

• Spans area between fence rails to support workpieces
• Laminated surface for durability and easy movement of material
• Fits saws with Delta 52-inch Unifence for a complete installation
• Shelf: 3/4 by 15 by 40 inches

Features

• Fits Bench Saw models 36-540 and 36-550
• Converts bench saw into floor unit for a more permanent shop set up
• Heavy gauge steel construction for durability
• Easy bolt together assembly and pre-drilled mounting holes for quick set up
• Includes plastic feet for stability

Reviews (4)

I like it
I found this table very easy to assemble. It is very solid and compact. It will be easy to store and transport. So far so good!!

adequate, but not ideal
The picture does not match the stand - mine is black, and has only one bolt at each anchor point. There were no instructions in the box, but it wasn't hard to figure out. You have to do the bolts up _really_ tight for it to be rigid (I used two wrenches). However, it does hold my saw quite well. I would have preferred rubber feet, as the plastic ones don't offer much friction -- when ripping a board the whole stand sometimes slides across the floor. It's also quite expensive for what it is, especially when you compare to the price of the saw itself.

So Bad, it's almost funny
I purchased the Delta 36-519 steel stand for my table saw
in October of 2001. When I received it, at first I thought
they sent me the wrong stand. No that was the stand alright.
Here is why you may wish to consider avoiding buying this
stand. The stand pictured above is gray and it has two bolts
for each support upper and lower. Mine had one bolt per
support. That in itself would not be a major problem but what
is the problem is that the metal they used is around the
thickness of cheap sheet metal. If you put the stand together
and pick it up it shakes like jello.
The person that wrote the reveiw that liked the stand may have
bought it when perhaps it once was the stand pictured above or
of a better quality.

Delta Steel Stand
I can't believe Amazon.com had this! It was the exact stand I needed for my bench saw...Very cool!

(Update to other comments...The stand I received is the exact one pictured above. Gray with enough bolts to properly secure the stand and bolt down my table saw. I have used it with my saw for over two years and it has not fallen apart and I have not needed to tighten it. Very dependable however I do agree about the feet. My stand's feet are plastic which does tend to cause it to slide when I am working with large pieces of wood. Rubber feet would have been better. If you do not get the exact stand then send it back and demand the gray one.) ... Read more

Features

• 1/2-inch diameter for sanding smaller contours and curves
• Aluminum oxide abrasive for long lasting, efficient sanding
• 150 grit for efficient stock removal with a finer finish
• 6 pack

Features

• Attaches to power take-off for easy set up
• Accepts sanding drums, polishing wheels, grinding points and more for detail work
• Fits Delta 31-050 and 31-080 sanders and 40-560 scroll saw

Features

• Fits Delta 43-188 sliding shaper jig
• Adds extra clamping power to the sliding shaper jig
• Installs easily into pre-drilled mounting holes
• Quick-release design for easy adjustment
• Flip lever clamp for quick clamping

Reviews (1)

Other Use
According to Delta, this clamp may also be used on the miter gage for 10" saws; especially usefull when crosscutting. ... Read more

Features

• Parting tool for dividing the work into sections before shaping
• High grade alloy steel maintains an edge longer
• Precision ground for smoother cutting
• 14" hardwood handles for better control

Features

• Fits Delta 32-325 and 32-326 Line Boring Machines
• Allows consistent repetitive boring operations
• Adjusts easily with spring-loaded locking handles
• Stop pivots out of the way when not in use
• Includes one right and one left stop

Features

• Center point and radial spurs for a positive, slip-free grip on the workpiece
• No. 2 Morse taper for use with standard wood lathes
• Hardened and polished steel for durability and a tight fit

Features

• Adapts Delta Left-Tilt Unisaws for dust collection
• Allows you to maintain a cleaner, safer work environment
• Installs easily over opening under motor cover for quick set up
• Outlet fits 5-inch dust collector hose for efficient chip collection

Features

• Universal design fits many brands of jointers
• Fits 6" jointers to provide proper airflow for efficient dust collection
• 4" diameter outlet for use with standard hoses

Features

• Molding throat plate foot the 36-730 Cabinet Saw

Features

• Ball bearing design for less friction and reduced vibration
• No. 2 Morse taper fits standard wood lathe tailstocks
• Hardened and polished steel for durability and a tight fit

Reviews (1)

"Economy says it all"
I went against my own rule and bought the economy version of a tool. I thought "what could be wrong with a live center?". Plenty. Initially, the bearing didn't turn at all. I ended up spraying some lube in the bearing (which isn't good for the bearing but it was the only way I could get it to turn). Now I just noticed that the point is GONE. The point/bearing housing is made out of some cheap cast pot metal and it obviously overheated when the bearing wasn't turning and just disappeared. So now it's virtually useless. Go for the more expensive live center. ... Read more

Features

• Fits most standard bench grinders with 1/2" arbors
• 6" diameter, 1/2" face
• For use with buffing and polishing compounds
• Cloth layers are stitched for durability and rigidity

Features

• 55-gallon capacity for collecting large amounts of dust and chips
• Fiber construction for lighter weight
• Aluminum foil lined for fire resistance
• Fits Delta 50-182 and 50-665 Dust Collectors

Features

• Fits Delta 50-183 collector drum and 24" diameter drums
• Five wheels for stability
• Eases transport of drum