Features

• Built-in width of cut scale for quick set up
• Cuts dadoes and grooves from 3/16" to 9/16"
• Carbide-tipped for long lasting sharpness and durability
• 6" diameter/ 5/8" arbor hole to fit most 10" table saws
• Adjustable for exact sizing of dadoes

Reviews (1)

disappointing dado...
I bought this blade because of its relatively low price, compared with other dado blades. Well I believe this is one of those, "you get what you pay for," situations. This blade does not give a very accurate dado cut, often leaving a scalloped cut rather than a square clean cut. Because of the adjustable design, this blade spins at an angle and produces an unacceptable vibration action. If I had it to do over again, I would have spent the extra money and bought a stack type dado blade. ... Read more

Features

• Accessory table for the 36-312 and 36-412
• Increases work area of miter saw table
• Provides added stability when cutting longer materials
• Attaches easily to right and/or left side of saw

Features

• Simplifies planer adjustments
• Accurate 10 within .001" tolerance
• Magnetic base for stability
• Rotating dial for versatility and ease of set up

Features

• Vitreous aluminum oxide for cooler grinding and sharpening
• 7" diameter
• 5/8" face width
• 5/8" arbor hole fits most standard grinders
• 46 grit for aggressive material removal

Features

• Wood fence assembly for edge sanding
• 3-1/4 inch by 7-1/2-inch size provides plenty of surface area for support
• Includes mounting brackets and hardware for easy installation

Features

• 2 pack
• 80 Grit
• 5" diameter
• Aluminum oxide abrasive
• Fits Delta 31-080 belt and disc sander and others requiring 5" self-adhesive disc

Features

• Adapts Delta 31-280 for use with sanding accessories for greater versatility
• Fits accessories with 1/2-inch arbor hole or a 1/2-inch power take-off spindle

Features

• Adapts Delta 31-280 for use with sanding accessories for greater versatility
• For use with abrasive flap wheels, buffing wheels, and other accessories with 1-inch arbor hole

Features

• Adapts the Delta 31-280 Sanding Center for edge sanding circles up to 48 inches in diameter
• Sliding pivot pin allows easier circle sanding
• Includes mounting brackets and hardware for easy installation

Features

• 1" diameter
• Sands a variety of curves and contours
• Includes rubber drum, abrasive sleeve, drum plate, and table insert
• Fits Delta 31-780 B.O.S.S. Spindle Sander

Features

• 1-1/2" diameter
• Sands a variety of curves and contours
• Includes rubber drum, abrasive sleeve, drum plate, and table insert
• Fits Delta 31-780 B.O.S.S. Spindle Sander

Features

• 36 Grit
• Bulk roll, enough for 14 abrasive changes

Features

• 6" diameter, 5/8" arbor hole
• Outer blades cut cleanly and smoothly
• Five inner chippers remove the bulk of material
• Cuts dadoes and grooves from 1/8 to 13/16"

Reviews (1)

DON'T GET THIS DADO!!!
I have seen this dado head and I have read about how poorly this dado head cuts. I think That a Thin Rim Dado is much better. But if I were anyone that owns a dado head. I would get the Avemger Products dado sets. They look exactly like the Systi Matic Superfine dado head but they have three things that the Superfine dado head does not. First of all, These sets are available in 6 and 8 inch diameters ranging from 20 to 42 teeth. They also include a 3/32nd inch chipper while Systi Matic does not and you get 8 shims and a manual as well. As far as I'm concerned, The avenger sets look really good to me. ... Read more

Features

• Fits Delta Contractor's Saws
• Provides proper support of materials while maintaining proper clearance
• Four set screws provide levelling ability to keep flush with table top
• Convenient finger hole for easy removal

Features

• Clamps workpiece securely for more accurate cutting
• Fits Delta 34-555 Sliding Table Attachment
• Tightens easily with top knob
• Padded clamp to prevent damage to the workpiece

Features

• Adds 13" of crosscutting capacity to your table saw
• Cast iron for maximum strength
• Installs easily onto front rail using included mounting bracket
• Fits 10" table saws with Unifence Saw Guide

Reviews (1)

Works OK but very weird install
First, this thing has a miter slot with no bottom groove, so you cannot use the full depth, but it does allow me to more fully use my Osbourne EB-3 miter gauge. Install is very challenging. The item has an unusual adjustment system that required about an hour to get right. The lip that is supposed to match up with your miter slot would not get parallel with the table saw table until I added two large washers. The slot was way too tight and required some serious file work to make it work. I like it, but it was a bear to get right. ... Read more

Features

• Set of three matched knives
• Cuts wedge tongue profile
• High-speed steel for durability and long lasting sharpness
• Installs easily on cutterhead with existing set screws
• Fits Delta moulding cutterheads

Product Description

mfg by: DELTA INTL MACHINERY CORP CARBIDE-TIPPED CIRCULAR SAW BLADE Features fine-grain carbide tips Highly resistant to wear Chrome-alloy steel body 35-617 10X50 ATB&R 15DEG BLADE 10"x50ATBR ... Read more

Features

• Fits Delta left tilt Unisaws
• Standard replacement for lost or damaged inserts
• Rear pin to prevent lifting