Features

• 145 acessories
• Reusable case
• Accessory Brochure with applications

Reviews (2)

cheaper at homedepot.com
Homedepot.com has this for $19.97

Nice assortment, but crappy case
If you've got a Dremel tool, but too few bits, this is the set to have. This set really gives you the most for your money, as compared to the other, smaller, Dremel bit sets.

That said, I should point out that the case really sucks. I like stuff to be in (roughly) rectangular boxes for ease of storage. This case has a handle, which is nifty, but protrudes a few inches above the case. This means you can't stack anything above it.

Also, the poor design of the lids means they won't open all the way, nor will they stay open unles you pry them up with the blue inserts. If you pry the blue inserts up, you risk spilling the contents.

Oh, and this can be had at the "Wal" place for twenty pesos. ... Read more

Amazon.com

We will admit that we think these rotary tools are some of the coolest things around; you can do so many things with them. But once we saw this attachment, we were blown away. If you don’t have the money or the space (or the inclination) to set up a whole router table assembly in your home or shop, but you still want to put decorative edges on wood projects, this is absolutely the ticket. It holds the tool under the table, and you mount your shaping bit in it. Turn it on, run your piece against the stationary tool, and your edge is routed. It also works great for small dado grooves with a straight bit. The new table surface is even smoother than before, and it’s plenty big enough for small craft projects. It’s also a great setup for sanding: Just chuck in a sanding drum and move your workpiece against it. If you’ve got a rotary tool, get this.--Kris Jensen-Van Heste ... Read more

Features

• For use with rotary tool models 275, 285, 395 and 398
• Convert your DREMEL corded rotary tool into a bench mounted wood shaper
• Features an adjustable fence, and a large 8" x 6" work table
• Slot, groove, sand and trim edges
• MultiPro tool not included

Reviews (3)

This will destroy your tool
I'd stay away from this one until the design flaws are fixed. Tons of sawdust from the piece you're working on will fall into your tool and render it useless. I've killed two Dremels, and got maybe a grand total of 5 minutes use out of the table.

Dremel Mini router table acessory
I have been using this for quite a while, and at times, it is a lot easier to use this, to dadoes for small items on soft wood like boxes. I used it to make some boxes out of pire and I used it to do edge work and make dadoes. This is my coolest acessory for the dremel with my wood bit set.

Good Attachment to have
A Fine piece of equipment. Works great even with pilotedbits. Highly recommend any dremel user pick one up ... Read more

Features

• Clear base allows greater visibility of work surface
• Two depth stops with quick release for quick, consistent adjustment of depth and for progressively deeper routing
• Depth guide includes English and Metric markings
• On board storage for router bits and wrench

Reviews (1)

Big Improvement, more features.
Dremel has really upgraded with this new plunge router attachment for the rotary tool. It fits all the usual corded tools and even the new Li-Ion cordless!
Great new features like: Plunge capability, clear base, bigger base, rotary tool mounting is very sturdy and rigid, depth stop, big edge guide that goes all the way to the bit.
The locking handle takes a little getting used to. Because it locks with one handle and plasic was used for the base there is a little flex back after locking. Plastic for the base to be clear is a benefit, but the plastic for the top plate was probably to save cost so they could price it closer to what the old router was. Anyway, when I really want to be accurate with my depth, I make sure to measure the distance from the bottom of the base to the bit with a metal scale. That way I know the depth is what I want. If it was all metal I'd give it a 5, but then the cost would probably keep me from buying it. It's great for the small router jobs I do(signs, door striker plate installation etc.) and I would recommend it! ... Read more

Features

• For use with rotary tool models 275, 285, 395, 398 and 780
• Comfort grip handpiece - allows finger tip control to cut, grind, sand, sharpen, polish and more!
• Integrated shaft lock button on the handpiece allows for easy accessory changes.
• Quick connect - easily attaches to your DREMEL rotary tool
• More flexible cable - provides more comfort during use.

Reviews (2)

Extending my reach...
I've found the flex-shaft to be one of the most useful Dremel tool accessories. It's great for those remote, hard-to-reach areas of my work pieces where the width of the tool itself would hinder my efforts, ot it just can't reach. It took a while for me to get the hang of using it, since it required a bit more hand control than I originally anticipated. Just make sure to keep it as straight as possible, and don't bend it too much- it heats up pretty quickly, especially at the bends. And heat's the big killer of this accessory. Also, be sure to have a bit of the flex-shaft grease handy for occasional lubrication.

The only thing that annoys me about the flex-shaft is that it won't accept a chuck to secure the bits, just collets. This can be a major frustration when I'm doing work that requires constant bit changes, with different bit diameters. Just when I thought I was rid of those pesky collets forever...

'Late

IF you don't have it you should
This tool is the most important attachment in Dremel's Inventory. All Users should get one ... Read more

Features

• Rotary tool not included
• Use with your DREMEL rotary tool to sharpen the dullest of chains
• Includes 3 sharpening stones - consult your chainsaw manual to determine which stone you need
• Contents also include the attachment, a gauge, 2 spacers, a wrench and an instruction manual
• For use with rotary tool models 275, 285, 395, 398 and 781

Reviews (4)

Best Sharpening I ever had
Previous to spending 10 bucks for the Dremel Sharpening attachment, I was taking my chains to a professional to have them sharpened. It pays to follow the directions in setting up the sharpener correctly, but, once you do, you'll get the BEST sharpening job ever. My sharpening job with the sharpener was far superior to any of the sharpenings that I ever got from a professional. Plus, the professional guys ground an 1/8th inch or so off of the teeth each time they sharpened my chains, when, in fact, all they needed to do was to put a sharp edge on the teeth. The Dremel sharpener works magnificently and gives you a phenomenally sharp edge that will last a long time [as long as you keep your chain out of the dirt!] For the price of this product, it simply can't be beat.

Instructions Incorrect!
When a chainsaw is sharpened, the sharpening tool is always referenced to the top of the cutting tooth (see the sharpening instructions from any saw chain manufacturer).

However, on Dremel attachment 1453, front of box, the picture shows the guide riding on the chain's depth gauge instead. Printed instructions on the back of the box (and supported with pictures) confirm this error for both left and right teeth.

To further confuse matters, the instruction sheet inside the box describes a method where the guide rides on top of the tooth for one side of the chain, but on top of the depth gauge for the other side! This is also incorrect, in addition to contradicting the instructions on the box.

Nonetheless, the device works adequately, especially if the user modifies the procedure to cause the guide to ride on top of the cutters for both sides of the chain.

In my opinion, this would become an excellent attachment if the instructions were rewritten, the pictures on the box replaced by correct ones, and the guide manufactured as a mirror image of the one presently sold. This would allow sharpening both sides from the non-engine side of the saw, thereby allowing two more teeth to be sharpened before chain repositioning. On an 18 inch bar this amounts to five rather than three teeth for left side cutters - a 67 percent improvement.

I have e-mailed Dremel with some of these observations, but received no reply!

Works Great!
I took a chance that this chainsaw sharpening attachment would do the job on my little Poulan electric chainsaw. It works great! Chains grow dull fairly quickly, particularly when you let the chain touch dirt. This little tool sharpens the chain like new and only takes a few minutes to get the sharpening job done. You can't go wrong. Dremel provides three different size sharpening stones that will accomodate most chains.

Much easier than a file
This works much better than I thought it would. Accuracy is equivalent to a handheld file but it's a lot quicker and easier. I don't believe this fits the battery operated Dremel so you have to use it near a power source. Installation on the Dremel tool is vary easy. It takes maybe 15 seconds longer than changing a regular bit. If you have more than one size chainsaw, consider getting two. They are not expensive and you save having to set it up each time you switch saws. ... Read more

Features

• Quick connect system easily attaches to your rotary tool in place of the housing cap without the need of tools
• Coupling system allows you to orient the right angle attachment on your tool in 12 different directions
• Ball bearing and spiral bevel gears give long lasting durability along with smooth and cool operation
• Compact design allows you to get into hand-to-reach places

Reviews (2)

Where have you been
This should prove to be a first class item. When working in cramped areas this is better then the Flex Shaft since you can get the whole tool in where you need it. Plus the quick installation is so useful.

The Right Tool for the Job
This attachment makes a versatile tool even more versatile. I've used it to trim sheet metal ductwork and make cuts in wooden siding in a tight spot under the floor of a room addition. I've also used it to trim off PVC pipe ends from the inside out. It adds a whole new aspect to the Dremel tool by helping me to reach those difficult spots like that. Frequently, I use it to cut off nails and screws that can't be removed. This attachment stays on my Dremel tool all the time now. I'm glad I bought this one! I'm still exploring its uses. Always remember to go slow and make several passes at the material as you cut so as not to overload the Dremel. ... Read more

Features

• Chuck allows quick and easy accessory changes without changing collets
• Accepts accessories with 1/32" to 1/8" shanks
• For use with DREMEL rotary tool models 275, 285, 395, 398, 750, 770 and 781

Reviews (9)

These once came standard with the flex shaft kit
I guess Emerson Electric figured they could make a few more pence selling these as accessories. By using these chucks you will relieve yourself of the trivial task of changing collets, but you will lose the precision and balance of collets in the bargain. These chucks are low-grade stuff indeed; they cause considerable runout and vibration in addition to the obvious clumsiness of their larger size.

Nice idea, but not 100%
While I do like the conevience of the chuck, it does not rotate 100% true. This causes a very slight wobble at the tip of any drill bit. I have tried 2 different chucks, but both yield the same results. I only use the chuck when absolute precision isn't required.

Awesome time-saver, but not for use with other attachments
I rarely use the standard collet that comes with the tool any more, after buying this item. No more looking for a wrench (which I invariably loose), etc. Beware, though: I took for granted that it would be compatible with my chainsaw charpening attachment. It is not. If you use other attachments, don't expect to be able to use this at the same time. If you don't use other attachments...well...go on to the next review. Well worth the buy, in my opinion

Cheap at twice the price
This chuck (which I consider to be essential) greatly enhances the convenience of any Dremel. You might be tempted to save the old collet device this chuck replaces, but before long you will discard it as useless trash. I do a lot of really miniature work and I find the chuck to be great for holding things as small as a 1/64th inch drill. I have one on each of my 3 Dremels.

Dremel 4486 MultiPro Chuck.
I don't understand why Dremel doesn't include this great little chuck as a standard accessory with all their Multi-Tools. It is so much easier, faster and less frustrating than fumbling with the tiny collar and wrench that the tools come equipped with. If you change bits on your Dremel often, as most users do, you will quickly come to appreciate the 4486. As for me, the 4486 is comparable to the Flex-Shaft as one of the single most worthwhile attachments available for adding versatility and conveience. ... Read more

Features

• Nickel-Cadmium
• Long lasting

Reviews (2)

Just where is the savings?
I refuse to buy this product from you for the following reasons! You advertise that I save $10. by buying a battery pack from you, then charge 33 percent of its value, or $10., in "postage and handling". That makes the $20.00 item cost $30.00. My biggest question is this: How can you possibly charge $10. postage for a tiny, light weight item such as this?
Roger Carlson
Winona, MN

A must-have accessory for the Minimite
The Dremel Minimite is a great tool for jobs away from AC power. Its single battery is good for most jobs; but, if the job goes into overtime (over 45 minutes of tool use), this extra battery is an absolute must. Rather than dealing with a dwindling battery at the end (and often most crucial part) of the job, pop in a replacement and finish with gusto!

Off line, while charging one battery in the charger, the second battery convienently sits on top of the charger housing. Number them 1 & 2 to differentiate between the two and you've got a winning pair for any job in the field! ... Read more

Features

• Includes 1/32", 3/64", 1/16", 5/64", 3/32", 7/64" and 1/8" drill bits
• Convenient storage case included

Reviews (1)

handy to have
These are great to have around so you don't have to carry a drill with you. Make sure you have the 4486 Chuck first, though. ... Read more

Features

• Accommodates all applications
• Contains 125 pieces
• Clean, polish, sand

Features

• For use with rotary tool models 275, 285, 395, 398 and 780
• Includes cutting guide, 2-#560 drywall cutting bits and 1-#561 multipurpose cutting bit
• Useful for making cuts in a variety of materials including drywall, wood, plastic, fiberglass, ceiling tiles, laminates and vinyl siding
• Cutting guide allows for a sturdy controlled cut with maximum visibility, and has easy depth adjustment
• Rotary tool not included

Reviews (4)

great practicality
I recently began using this attachment with my Dremel to create prescise lines at uniform depths. Using this attachment, I was able to achieve the results I was looking for. The variable depth is very helpful, but a little inaccurate. Still, I would recommend this product to anyone who is looking for a simple, but very helpful attachment for their Dremel.

Very useful
You can control the tool very easy with this attachment and better of all is compatible with the RTX of Black & Decker.

There to guide me...
Although this device is meant more for drywall cutting, I find it to be a useful tool when I'm cutting out narrow, shallow depressions in styrofoam for miniature landscape crafting. When I want to cut down to- and maintain- a specific depth, the guide lends me a really big assist.

Sadly, it's one of those accessories that require the use of collets, rather than a chuck, on the rotary tool. Not a really good thing when I'm constantly changing bits, and want to do it quickly. Oh well...

'Late!

One of the Best Attachments out there
IF you were to see how cleanly this kit cuts through Drywall you would know how great this tool is. The cut is nice clean and straight. No wraggly cuts like with a saber saw or keyhole saw. We used it to cut the hole for the box while Mounting Ceiling fans in the Master Bedroom and Living Room of our house and it was Indispensable. ... Read more

Features

• For use with rotary tool models 275, 285, 395, 398 and 781
• Now grout removal is easy.
• Easily screws on to the front of your DREMEL rotary tool
• Removes both wall and floor grout
• Includes #569 - 1/16" Carbide Grout Removal Bit

Reviews (9)

Works great, and fast too!
The grout removal attachment delivered as promised. It took the grout out so fast I was actually surprised. I have tips for success: 1. Always pull the tool, if you push it backwards the tip may break. 2. Use a shop vac to clean up the dust periodically as you go. Suck or blow out the tool with air from the vac to get the dust out. 3. Stand back and admire a job well done.

Nice idea ......................but.
After starting the degrouting job on by tub/shower i purchased a new dremel motor and this tool. The grout was 1/16" give or take and the grout was 20 years old. the bit cuts great and i did end up breaking 3 bits (@ $11.00 each). i was only 1/3 of the way done. The motor itself began having bearing problems, 3 hours into the job, due to grout dust ingestion. Home Depot gladly swapped tools. The worst part of this tool was dust blown all over the house. Finally took a hammer to the job and went to the studs and in the process found some serious potential problems. After 50.00 of hardibacker, 8.00 of tarpaper, 20.00 mastic, 110.00 in tiles, 12.00 grout and 15.00 misc i had a better job done with some potential problems fixed. It took 1 week of evenings to finish.
This is a good tool for a tile or two but to regrout a full surround (that is fairly old and you plan on living in your house not selling)..... I think you would be money ahead to at least consider a different route

Great attachment
I bought this attachment to finish cleaning the grout out of my tub/shower. I had done some of it by hand, but with my bad wrist, it was too much. I actually didn't use the bit that came with the kit, I bought 6 bits from leakyshower.com, for the price of one dremel bit, and only needed to use one to do the entire job. I had heard that the bit that comes with this attachment breaks easily, so I didn't bother to try it. I just bought the bits from Leakyshower.com.

Save $10 and just buy the bit
The attachment doesn't keep the bit centered and won't work near corners. The housing has two tabs that are supposed to guide the bit along the grout line. The problem is that the housing is made of cheap plastic so when you tighten it it distorts and causes the bit to be off center. This is only good for very small jobs and they tend to be near corners, so for get this tool. I found that I could easily complete the job freehand. So just buy the bit size that you need and save $10 (or $15 in some stores).

Dremel Grout Removal Kit When Doing A Floor
This works OK for a small floor area only such as 1 or a few tiles at most. Due to hardness of the grout the bit will definately break ([price] to replace)after about 10 mins or less of use. Dremel is aware of this issue and doesn't recommend this kit for more then a small area. Walls are OK if the grout is a softer or vinyl enhanced grout. If you do use this, stop frequently to allow the bit to cool and you may be able to get the bit to last a bit longer.

For floors, use a Dremel with a Carbide Cutter Bit (the one with a star pattern and pointed) and this bit will last forever. Use w/o the Dremel kit and be carefull at the corners of the tiles as this bit will cut into the tile if you don't keep it moving through the intersections. The point allows you to get the grout out of small areas or large.

Note that everyone whom has done grout work on a floor has tried it and quickly broken the bit which comes with the kit. It's easily returned broken though where you purchased it. Dremel's customer service says to return it to them if there's an issue with the store. The realize that the packaging is a bit misleading in regards to the kit's capabilities. ... Read more

Features

• Cut or slot bolts, screws, sheet metal, wood, plastic
• Set includes high speed cutters, sanding accessories, cut-off wheels and mandrel
• See mfg review for specific list of items included

Features

• Includes 4 collets--1/8", 3/32", 1/16", 1/32"--and collet nut
• Allows you to quickly change collets to accept bits with shanks of 1/32" to 1/8"
• For use with all rotary tools EXCEPT models 1, 2, 260, 270, 280, series 1 or earlier

Reviews (3)

Gotta have it
The quick change collet nut comes with every Dremel rotary tool but if you loose one you're sunk. It's good to have an extra one on hand in case the unthinkable happens.

Indispensable part of the Dremel
You really can't use the Dremel to its fullest without the Dremel collet nut. The Dremel Chuck is nice, especially if you are always changing accessory bits because the Chuck helps save time. I like the collet nut because nothing holds the bit tighter than the proper sized collet along with a collet nut. I use my Dremel hard, and the collet and collet nut makes sure the bit does not work loose.

Pass this by and get the chuck instead
Change out different collets to fit different diameter Dremel bits? I don't think so. You'll save yourself quite a bit of time, energy, and frustration if you get the Dremel 4486 MultiPro chuck instead.

The chuck costs a bit more, but if you do projects that require constant bit changes, it'll be well worth the money.

'Late! ... Read more

Features

• Disc of hard abrasive
• Cuts, grooves and trims
• Cuts metal, wood and ceramics
• Five per package

Features

• Multipack includes 1 pc 80 grit, 2 pcs 120 grit, 2 pcs 220 grit

Reviews (1)

Great for sanding contours
The sanding tubes are the best approach to this type of sanding. They fit all the shapes available for the Dremel contour sander. As the sandpaper wears, the tube can be rotated on the shape to provide a fresh surface. This allows maximum economy. The tubes are easily changed. I use then for a broad range of sanding tasks on miniatures and full size projects. ... Read more

Features

• Three hour charger
• 4.8-volt

Features

• Diamond point for the Dremel 290 Engraver
• Use this point for continuous duty or commercial work
• Can also be used for decorative engraving

Features

• Cleaning/polishing bit set
• Contains 20 items
• Variety of applications

Features

• Long lasting tungsten carbide coated wheel
• Use the face of the wheel for shaping; use the edge of the wheel for cutting
• For use on soft and hard woods, fiberglass, plastics and laminates
• Not for use on metal

Reviews (4)

Beginning to look a bit worn and tired.
My cutter has cut everything from balsa to hardwoods, and even some wire and plastic. After two years it really isn't worn out, but I am now ordering a replacement-- just in case I need it in the next year or two. In answer to the last reviewer who wonders what bits are available to fit Dremel tools. If he would use the universal chuck he could use any bit he could shove into it down to sub-miniature bits like I use to drill holes through toothpicks used to make small parts on ship models.

The Artworks Gallery of Carvings
I use all the dremel products to carve my projects..My company would like to purchase at a wholesale prices, to order special bits that i use on a regular work load. I would like to request a list of all the bits that fit your dremel tools. I plan to place a hugh order,and don't know how to contact the dremel company in order to take care of this matter..can you please send me information for business purchases.
I need this information asap..as I have projects waiting to be finished.

Thank You for your time.
Viki Pierce
The Artworks Gallery of Carvings
559-905-0385
@1334 robinson ave.
Clovis,California.93612

A GERAT CUTTER FOR USE IN PINE
I needed something that could cut through wood like butter and I found it! This great carbide slotting saw cuts through pine like nothing! If you take enough passes, you can cut right through! This bit hogs out alot of material. So if you like to use it for hobby work or if you need something that will hog out slots in wood quickly this is the one to get. In fact, I have almost used mine up to the point where I think it's time to get a replacement! I peronally reccomend that you use it in pine. it really lets the wood chips fly!

Durable, useful
Gives your Dremel the ability to cut through tougher material than the standard cut-off wheels, and also lasts much longer. Use standard precautions, it does build up a LOT of heat and can produce sparks. ... Read more