Features

• Locking castors
• 600 pound capacity
• Adjusts from 18x18 to 28x28 inches
• Easy assembly
• Two fixed and two swivel casters

Reviews (7)

Good Choice for Heavy Equipment
After reading reviews of the HTC 2000, and knowing about the Delta UMB from personal experience, I decided to give the Jet a shot. I am glad that I did. Before getting to the review, though, five stars to Amazon's shipping department which shipped this product within a couple of hours of the time I placed the order. It hasn't arrived yet, but I bought a second one from my local tool shop. (OK, I'm weak. I couldn't wait.)

This mobile base was very simple to set up. The spring-loaded pins locked firmly in place, and I was able to perfectly size the base to the cabinet of the 8" jointer that now rests on it. To ensure stability, I cut a sub-base from 3/4" ply, placed that on/in the base, and then placed the jointer on top of that. I then bolted the two side tabs on the jointer cabinet to the ply.

With the wheels running opposite the length of the bed, the jointer does not move at all when being used. When it does get moved, though, it is very smooth and confident. I can't give five stars - those wheel locks are an unfortunate wart on an otherwise excellent accessory.

simply awsome
This base is awsome. I moved my table saw to this from a delta base and couldn't be happier. The assembly took a total of about 5 minutes since there is no hardware to worry about. As to the people that saw this doesn't lock well enough for a table saw, turn the base 90 degrees. No mobile base should be set to roll in the outfeed direction of a TS. If you lock the back (fixed) casters, then the front casters can't turn so it becomes very solid.

Wheels move when locked
I've been using this base under a jet contractor's saw with cast iron top for a few months now. The base is very sturdy, strongly made, and rolls smoothly. The big problem is that the wheels don't lock solidly, and I can't trust the saw to stay in place when I cut a large piece of plywood, etc. I'll probably buy a different base for the saw and use this one on something else like a drill press that only needs vertical support. Bottom line is it doesn't do the job for a table saw.

JET Heavy duty universal mobile base
The base is well made, assembles VERY easily and quickly but has a major flaw - the LOCKING wheels do not lock well enough to prevent the saw from moving when you cut heavy material. This is dangerous and makes accurate cuts of larger material impossible. The rotating casters are the worst offenders.

I'm disappointed because it is a well made unit and Jet usually produces good quality products. As an engineer I view this as a design flaw rather than a quality control issue.

Great Simple and Strong Base
I bought this base for my 14" bandsaw and couldn't be happier. It goes together in 30 seconds instead of 30 minutes like the HTC mobile bases. All 4 casters lock securely enough to hold my saw in place. While one reviewer complained that two casters are fixed, that is so you can steer the tool when moving it. I own both the HTC and Jet mobile bases and the Jet is superior. If you need a good mobile base that is easy to adjust and assemble, buy this one and you won't be dissappointed. ... Read more

Features

• Chuck also comes with 3/4-inch screw center
• Original Nova chuck
• Four-jaw chuck
• Standard 2-inch external collets
• Expands into 2- to 3-inch dovetail recess

Reviews (3)

Great chuck
After having a 3 week wait for the insert for my lathe, I put the chuck together and made a little goblet with it to give it a little test. Being kind of new to turning, any woodturner would appreciate my hesitance at turning a piece of wood being only held at one end. But I found that once I tightened down the jaws, I could grab the piece of wood and lean back on it, and that piece of would was NOT going to come out or even loosen! I was able to turn the whole goblet without ever adjusting the chuck or even paying it any attention at all. The instructions for putting it together were great, and is really easy to use. My only thought (regret) would be that if this chuck performed this good, how much better is the Supernova chuck? GREAT value for the money, especially if you have a less powerful lathe where getting a bigger scroll chuck may be too taxing on your motor. Would definately get this guy. Comes with all the tools you'll need to use it, plus a heavy screw for screw chucking.

Great chuck but what about LH threads?
Conspicously missing from this product is the availability of LH thread inserts. Most bowl turners turn on the outside of the lathe. Unless you have a reversing motor (IE a newer lathe) you need LH threads. Some of Nova's competitors do offer the LH thread.

Nova does offer a blank insert so you can cut your own thread but you have to have a metal lathe or a left hand tap.

Nova Chuck Review
I have been working with this chuck for 8 years. I bought the chuck when it was first introduced into the UK where it is more expensive than here. I liked the precision and the way it emmulated metal working chucks in its versatility. It is well made and has never given me any problems. Although it may have competition, I like the quality; I would definitely buy it again. ... Read more

Features

• Accessory for JET JWBS-14CSW
• Two 18-inch guide bars
• 18-inch rip fence

Reviews (6)

Good Fence w/ resaw attachement
I got my unit today, on-time. I agree with the other reviewer that this unit is not what the picture displays and it is actually a much better design. It also has the resaw attachment that I was originally planning on making myself, but, I guess there is no need for that project now ;). Overall, it is nice and sturdy and all the fasteners and the powder coating on the parts, is high quality stuff. If you need a fence for resawing and other activities with your band saw, this is the one. Go for it.

14" Rip Fence w/ Resaw Attachment
I got my unit today, on-time. I agree with the other reviewer that this unit is not what the picture displays and it is actually a much better design. It also has the resaw attachment that I was originally planning on making myself, but, I guess there is no need for that project now ;). Overall, it is nice and sturdy and all the fasteners and the powder coating on the parts, is high quality stuff. If you need a fence for resawing and other activities with your band saw, this is the one. Go for it.

Like the fence but the picture is wrong
As I say in the title, the picture on Amazon.com's site is not the fence I received. The fence I received is much better. Looks just like a miniture version of the fence currently on the Jet contractor saw. Nice locking mechanism and scale.

Easy to install, a little harder to set up. Follow the instructions and after you have it in place and move it around, you'll figure out how it should be adjusted. It's really just a matter of raising and lower the front and back rails till the fence is even.

JET JRF-14 708718 Rip Fence
Bought a Ridgid 14" band saw but Ridgid quit selling the rip fence for it. Tried a Craftsman, but found it to wobbly on the backside. Went for this Jet model and the rails fit right into my predrilled table holes. Had to drill a hole about 1.5" back from the end on the underside of the fence to fit my table and lock more securily. Had it installed in about 20 minutes and it locks down tight with no play. Also comes with a resaw block.

JET JRF-14 / 708718 Rip Fence
This fence is basically a miniature version of the fence found on the Jet 10" contractors style saw. It is built tough and easy to adust. Once it is adjusted, it stays that way. The fence scale is also extremely accurate and has a micro adjust pointer which can be used to bring your cuts accuracy to within a 32nd of an inch. By far, the best bandsaw fence I have seen and used. ... Read more

Amazon.com

Any woodworker who will tell you he or she has never wished for an extra set of hands is lying. Here's that wish granted. Simplicity is sometimes the best design in a tool, and here, there's nothing to tighten, turn or twist. You just push the clamps where you want them, and your joints are aligned perfectly. They'll work with 90-degree joints, T- and butt joints on material up to 7/8-inch and of any length. They're made of stainless steel with a tough composite, and they won't scratch or mar your workpiece. They're foolproof, convenient and perfect for the cabinet maker, contractor, homeowner or home woodworker.--Kris Jensen-Van Heste ... Read more

Features

• Stainless steel spring jaws clamp 90-degree and Tee joints with ease
• Unbelievably fast and simple to use
• No limit to material length
• Holds work in perfect alignment
• Secures boards up to 7/8-inch thick

Reviews (4)

AnacondaJack
Outstanding clamps for one-person operations. But you need more than one set (of two) for normal cabinets. I bought two sets (four clamps) and thinking about more.

These things are great!!
These clamps are simple and they work perfectly. Won't ever build cabinets without them again. I'll be ordering more to save even more time during fit-up.

Like two extra hands
These are great, I used them yesterday to put togeter some cabinets. They held the two parts together untill I had put in some brads. The springs are strong and hold the timber very solidly. Get yourself a pair !

A great helping hand
These things work great. They are very quick and work just like you would think. They do not pull boards together, but they do hold them square and where you put them. ... Read more

Features

• Also fits the Delta Midi-Lathe
• For use with JET Mini Lathe
• Adjustable height accommodates all wood turners
• V-style leg design provides greater stability
• Comes with adjustable rubber feet for leveling to uneven floors

Reviews (1)

Must have for mini lathe
Unless space isn't an issue, you'll want this stand. Since I use the lathe less frequently than the other tools in my shop, it's nice to throw a dust cover over the set and roll it out of the way without giving up counter space. ... Read more

Features

• All steel construction
• Scratch, rust, and corrosion resistant
• Perfect for industrial or commercial applications
• Easily adjustable to ceiling, floor, wall, or truck mount

Features

• Improve filtering efficiency
• Keeps air cleaner and healthier

Reviews (5)

Works great
Just recieved it today and it was easy to install. I have a DC-1200 dust collector, so it did not require the retro kit. Right away I noticed an improvement in performance. My floor sweep is the furthest away (50 feet), and it sucked up the chips faster than with the 5 micron bag I was using. I think the canister and the retro kit should be sold seperately, because I now have a housing kit that I have no use for. the canister itself will fit directly on any 20 inch dust collector. It is also easier to clean than the filter bags. You just turn the handle at the top, and a flapper inside knocks loose the dust. If you are considering a dust collector, get one with the canister filter.

So far so good
After a bad experience with a local woodworker's supply I ordered the conversion kit from Amazon. I have to admit I was surprised at how quick the item shipped. It arrived in good shape and only took a short time to change out the parts and set the canister in place. I haven't had the opportunity to use the dust collector much since the conversion, but did cleanout the sawdust in the bottom of my table saw and found that everything seems to work as advertised. I also really like the clear collector bags, as in the past I had to check the bottom cloth bag by shaking it to see how full it had become. Now it just takes a quick glance. If this thing works as well as I hope, I think the shop will be considerably cleaner and the dust collection more efficient since the canister claims to give a better air flow and filter finer particles.

Great Idea but pricey!
I have a 3 HP Powermatic dust collector which has 4 bags. I ordered two retrofit kits when they were on back order. The estimated delivery time was well over a month but I received them in about two weeks. They both arrived undamaged, complete, and on the same day. If you have a dust collector other than a Jet DC1100 you receive an adapter that you can't use but I didn't realize this when I ordered these filters and maybe you can purchase them separately at a reduced price.

The filters fit perfectely on my dust collector and seal very well. A very simple installation! Although I like these filters and they greatly reduce the height of my dust collector (by over 3 ft.) and increase performance. I think the price is a little high. My dust collector complete cost approx. $600, these two kits were [less]. I would recommend buying a Jet dust collector with the cannister filter already installed instead of separately (the cost is comparable to dust collectors with bags). I bought these because my collector is in a shed behind
my workshop with a 7' ceiling. I had no choice except to put it in my already cramped workshop.

I think Jet has a good idea here and if you are in the market for a new dust collector I would certainly check out the new Jet cannister filter models. I have not used this filter long enough to give any advice on how well it holds up but it seems well made. I have to wonder if the filter media would eventually become clogged at least partially with fine sanding dust that the flappers would not loosen. I know that bags lose some of their efficiency after a lot of use because of fine particles lodged in the pores of the material, but new bags don't cost $189.

Dust Cannister retrofit revisited
I wrote my earlier review when I received a box that contained only the 20" retrofit, which is the middle part of the dust collector. The converter allows you to attach a clear plastic bag at the bottom of the dust collector, replacing the felt bag, This makes emptying the bag a breeze. Just take it off, tie it off with a twistie, and put a new plastic bag in place. The bag is secured with a cloth lined snap ring, and is a huge improvement over the old metal band.

It turns out the cannister arrived the following day in a separate box, although neither the invoice or packing slip indicate there were two boxes. The nice thing about the cannister is that it is about 18" shorter than the bag it replaces, and it is a WHOLE lot less dusty. I've haven't had the chance to run this for any length of time, but just in the ease of changing the lower bag and the 2 micron filter capacity and reduced size of the cannister makes this a winner already.

NOT what is pictured
I ordered the cannister that was pictured as the 20" retro kit with houseing. What I recevied was an adapter, ie. the middle of the dust collector that accepts the bottom bag and the top cannister. I have NOT received the cannister fileter. I'm trying to figure out if this is a two part shipment or if the catalog listing is just wrong. In either event, what I thought I was buying based on the picture and description is NOT what I received. ... Read more

Features

• Connect two machines to a dust collector with this kit
• Blast gate controls airflow
• One W1015, 4-inch Y-fitting; and 10 W1317, 4-inch band style hose clamps

Reviews (1)

Everything You Need - Plus Some
A nice, easy to order kit of the needed items for a DC system. The kit includes 2 blast gates, one "Y" connector, 10 wire clamps, 2 ten foot sections of hose, a table saw hood and another dust hood, all for a 4" system. You save a few bucks by ordering the kit versus each item separately.

All connectors went together with the hose as required, the wire clamps fit snug, everything went as well as could be expected. A few holes needed drilled in the table saw hood for attachment, but that is expected for a universal type attachment. No complaints, problems or issues. Just a good product. ... Read more

Features

• Front, and rear blade guards
• Accessory kit for JET JWBS-14OS Bandsaws
• Increases cutting capacity from 6 to 12 inches under the guide
• 6" Cast Aluminum Riser Block and hold-down screw
• 105" saw blade

Reviews (8)

Worked for Craftsman with a few modifications!
I have the Craftsman 14" Bandsaw (22424), also made by Reliant? It's a great saw, 2 speed, 1.5 horse motor. Unfortunately, though it [wasn't cheap] less than the Jet, it also had a 6" throat depth, and for resawing planks or rounding corners to turn a bowl, this was just not useful for me. I found the Jet accessory, and with modification time, by myself, I had this thing installed in less than an hour.

In order to proceed successfully, you need a handheld grinder and a table grinder with a decent wheel. You'll notice that while you're installing the kit the instructions are a bit off. You will need to remove the switch plate, but not unplug it as you would on the Jet. You have to do this in order to get at the screw hidden behind it. You also have to remove the 4 screws and take off the lower door to get at the lower plate. You need to grind off (or drill for new) studs that hold the top assembly to the base. There are 4 to grind - the ones on the new spacer block and the ones on the old block. It's pretty apparent, and you have to grind only about a half-inch from the 3/8" studs for the block to fit.

Once it's together (balance the screwhead/washer _inside_ the block while you carefully place the top, it will catch and hold the top upright while you tighten), you'll have to grind a 1/16" or so tenon about 1.5 inches up from the bottom of the saw-foot support column. You'll see what it looks like once you get the old one off. Once that's together, you're set, and can saw away. Mine's been holding up for awhile, even though I worried about the stability with the little studs gone. It's fine, and saws through 10" rounds like they were butter. As everyone else said, get a new blade right away. You'll be glad you did. A 105" 1/2" 3TPI blade works wonders for resawing.

This is a great deal, and gives you a whole new saw. You'll love it! I wish I could give it 10 stars! For [not very much money], I feel like I have a brand new [top of the line] saw.

Great addition....
If you do a lot of resaw or as in my case, make a lot of bandsaw box's this is a great addition. As other's have mentioned its a two person job, but the instructions and materials are top notch.I would also reccommend that you add Carter type guides to your saw at the same time. These really help with the resaw aspect and are a must for the small blades used in making bandsaw box's. The included blade wasn't much but I didnt think it would be, so no dissappointment there. The rest of the parts were good quality and everthing fit well. Took about twenty minutes to install and a few more minutes of adjusting. Thanks to the other reviewer for the tip on reinstalling the power cord. With a Timber Wolf 3/4" resaw blade I can now square up larger pieces of "firewood" to use for my bandsaw box's and it also enables me to get away from the 6x6 dimension that was my standard. I would reccommend this add on to anyone wishing to increase the size of material they can work with.

You better have the right tools, or 2 people
This would take 2 people with the right tools about 10 minutes. It took me 1 hour...mainly because I don't have a 15/16" wrench and my adjustable pliers would barely fit. Furthermore, my attmpt at hanging the upper arm from the rafters while tigtening the bolt 1/4" turn at a time was...uhh...nearly very dangerous. I am glad I made the purchase, but in the future would love to have known that I needed allen keys, and a crescent wrench set and someone to hold the upper arm while I tightened the nut. This thing is rock-solid, and makes resawing 12" quite the pleasure.

Still no riser block
Wish I could give an honest review of the actual product...don't let that disclaimer of shipment in 1 to 2 weeks fool you!!! I ordered mine on May 19th and as of today, July 8th, no riser block. Amazon continues to delay shipment every couple of weeks with an estimated delivery date now of sometime at the beginning of August. You would think that with the Jet bandsaw as one of their better sellers, they would keep a good number of these on hand. I am about to take my business elsewhere!

Added versatility can't be beat
...no matter where I looked, Including JET's own site, I could not come up with a listing of included parts, and the tiny picture of kit found on everyone's web site is nearly useless. Sure I trust JET -- but only to a point. For those like me who have modified their bandsaw with accessories like the Carter de-tensioner, or roller bearings, rest assured this kit will still fit, and you won't lose any functionality.

The parts in my kit were as follows:

1. Rear blade guard (metal, not the cheezy plastic that came with the saw)

2. Longer v-grooved shaft for the front/upper blade guard, enabling your upper guides to extend all the way to the table-top. Read the instructions carefully to install this one, or you'll be chasing a very small ball-bearing around your shop.

3. Front Blade Guard -- sheet metal, just like the original, but with an adjustable extension. Mine didn't quite fit the bolt holes, even on the OEM guide, but a couple passes with a file fixed it in short order.

4. Cast Aluminum Riser Block and hold-down screw.

5. 105" saw blade -- toss it out and buy a TimberWolf brand.

Assembly was a snap. Mine went together in about 20 minutes. The hardest part was balancing the upper roller assembly while tightening the hold-down screw. Not really too big of an issue, but a third hand to hold the bolt steady while you hand-tighten the nut would be helpful. Alternately, you could do as I did and use a piece of tape on the bolt head to keep it from turning as you snug the nut.

After it's all set according to included instructions, you may want to go one step further and tap a 10-32 hole in the back of the original lower cast aluminum bracket. It will allow you to re-use the original power cable loom (W shaped bracket) and thus keep the power cords from chafing on the lower blade door. The instructions don't call for this, but it's never a good idea to allow power cords to rub against sheet metal. ... Read more

Features

• Reduces 4-inch OD line to 2-1/2 inches OD
• 4" to 2-1/2

Reviews (17)

Reduce Hose Size, Increase Air Suction
If you need to step down in the DC system, which is recommended, this works great. The ends are to size stated, the hose fit easily and the wire clamps put it all together snuggly. The fitting allows you to step down from a larger main line to smaller branch lines near the machine, thus increasing the air suction, where it's needed most, by the machine.

Does not adapt the JET 6" Jointer to a "standard" shop vac
This adapter had the proper O.D. on the 2.5" side so that the end of my shop vac. hose fit in properly. But the dust chute on the 6" JET Jointer I bought from Amazon.com has the same O.D. as the nominally 4" side of this adapter (so they don't fit together well). No big deal for me: what I did was take a thin-blade hack saw, slice four cuts at 90 degree separation in the walls of the ~4" end, slip it over the dust chut on the jointer, wrap duct tape around the outside of the adapter's large end (while attached to the jointer), and now I've got a removable adapter that actually works. If you can't find the right part (I could not, looking high and low), this is a reasonable solution for those who can handle the minor frustration of the imperfect solution.

The two most popular sizes can now talk to one another
This adapter is great for mating the popular 2 1/2" vacuum hose size to your 4" hoses. This 4" is a male end that will fit well into your 4" hose acting as a female, and the 2 1/2" end is a female that will receive your 2 1/2" hose as a male. :-) I don't know why that is so funny, but it strkes me that way. That is the best description I can give it. These Jet adapters fit perfectly.
To securely connect this adapter, I suggest that you buy the Jet wire connectors, instead of the standard band clamps. Since most dust collection hoses have a wire running through them, band clamps can not compress them. The Jet wire clamp goes around the wire in the hose, and it grips the material directly to the fitting. I tried using the band clamps, and after having to reattach them on a regular basis, I went to the Jet 4" wire clamps, that is why I am making such a big deal out of it. I have never had to retighten, or reinstall the hose on the adapter since. The wire clamps work perfectly. Highly recommended.

Fits great!
The description by Robert Feeser (one of the top 500 reviewers in Amazon) explains 'This adapter is great for mating the popular 2 1/2" vacuum hose size to your 4" hoses. This 4" is a male end that will fit well into your 4" hose acting as a female, and the 2 1/2" end is a female that will receive your 2 1/2" hose as a male. :-) I don't know why that is so funny, but it strikes me that way. That is the best description I can give it. These Jet adapters fit perfectly'.

Not as pictured
The adapter I received has a flat interface, not the funnel style shown. That makes a difference if using the piece with the airflow going from 4" to 2 1/2" due to increased turbulence.

If you're planning to use this downstream from large to small diameter then I suggest you find one that is indeed funnel-shaped. ... Read more

Features

• Fits left or right tilt saws with 3/8" and 3/4" miter gauge grooves
• Includes quick release lever

Features

• Wire hose clamp
• 4" diameter
• 5-pack

Reviews (7)

The Best For Hooking Up Hoses
I've tried the band type of clamp and they simply do not hold over the long haul. The wire clamps allow you to tighten the clamp down for a firm grip in the fixture. My opinion, the wire clamps are the best thing since sliced bread for hooking up a duct collection system.

The Best Clamp...The Best Price
If your hooking up a dust collection system, the proper clamps can make all of the difference. The standard band type clamps are not properly suited to the job. The unique thing about dust collection hoses, is that they are generally made out of smooth, slippery plastic, with a stiff wire running through them for support and/or grounding. This poses a problem for standard band clamps, because the clamp is too wide to get between the wires. Therefore you have a clamp pushing down on the wire. Since the wire is rigid and in a circle, you would have to compress the circle (ain't gonna happen). Therefore a wire clamp such as these, with twin rigid wires is just what the doctor ordered.
I tried everything from duct tape, which gets soft after a while and loses it, to band clamps. When I finally got a set of these, my hoses stay put, and they don't leak. They are easy to install, and you can put a good torque on them, and not have to worry so much about them messing the thread the way a band clamp does. With the Jet 4" wire hose clamp you are dealing with a nut and a threaded bolt instead of a screw and some sheet metal. Definitely a lot stronger with the Jet wire.
The bottom line, when attaching a 10 foot-4" vac hose to a plastic 4" fitting, you can pick up the hose, move it around, and not worry about the hose coming off, the way it does with the band clamps sometimes.
Great unit, great price, get a few extras. Hope this helps.

Hands Down - The Best Clamp
I read other reviews before purchasing this clamp and am really glad I did. What I like is that the wires make great contact between the ribs of the hose and screw down very tight. Later I purchased the flat band kind from a local store and agree that this wire type is much better. It's much beefier than I thought it would be. Definitely the best clamp I've come across.

Great product to get you to [a minumum qualifiying dollar amount]
If your close and need to get over [a minumum qualifiying dollar amount], this product will do it.

Free Shipping!!!!

Best clamps for 4" work
These are the best clamps for your 4" collection needs. Easy to attach, hold well. I have had zero trouble with these. They also provide excellent grounding points for your dust collection system. Overall and excellent investment. ... Read more

Features

• Black ABS plastic hose
• 4" (exterior diameter) by 10'

Reviews (2)

Don't Get Hosed !!
This is an excellent Dust Collection Hose. It does measure a consistent 4" and always fit easily over the connection fitting. It is somewhat flexible and very rigid, but will not coil back into itself. This might be a problem if you move your equipment back and forth.

The other hose options are a Clear Hose, which allows you to see any possible clugs and air blocks in the DC system. And there is a 50 foot coil hose, which is not as rigid, but it is sturdy and it will coil back into itself, allowing for the movement of machinery.

I used all three in my DC system. The clear hose where large particles would be generated (lathe, bore machine), the 10 foot rigid hose in areas that would always remain fixed in location. And the 50 foot coil hose (cut up, of course) on machine that I move back and forth from the wall to the garage floor. I don't have endless space in the garage for all the "needed" equipment I have to use.

All three hoses work just fine, no problems, no issues.

Works Great!
I use several of these hoses in my shop to connect power tools to my Jet vacuum system. They work great. They work the best with the wire clamps. I recommend using a distribution of rigid plastic or metal pipe to get to the woodworking machine, then use one of these hoses to connect the machine to the rigid system. These hoses also can be used to vacuum the floor or other areas but are a bit clumsey due to the large diameter. ... Read more

Features

• 6-inch jointer knives
• Set of 3
• High speed steel

Reviews (1)

tw
Same kind performance as others but over priced! Try out Freud and the kind from Global Tools at half or less than half of the price. Can you tell the difference? ... Read more

Features

• Allows quick hook-ups
• Perfect for mobile dust collectors
• Smooth end style

Features

• Tap wrench
• Tap handles
• Metal case
• One year warranty

Reviews (1)

If you like having the proper tool on hand, you need this
I hated having to run to the hardware store whenever I needed to tap a hole I didn't have the right tool for. This set has just about any size you could imagine needing, in metric and standard, in starting taps and bottom taps, and small pipe threads too. The quality of the taps and dies are high, although one of my tap holders was kind of cheesy. The case is also nice - the pieces are encased in a hard-rubber form that is well-marked and protects them well. I think it's worth the money, especially if it prevents a few time-consuming trips to the hardware store! ... Read more

Features

• V-Groove pads included
• Use for all your household projects that need filing, framing, sawing and more
• Porta-lock base is lightweight yet durable
• Also functions as a bar clamp, spreader and workstation
• 360 degree swivel

Reviews (3)

Great product, awful packaging
I find this a fine product for light work. It does double duty as a convenient wide-jawed clamp or spreader.

But whoever designed the hard plastic packaging should spend eternity in hell unwrapping these things. NO thought was given to the buyer's convenience. Even with sharp industrial shears, it is VERY difficult to remove from the packaging. I would not buy another for that reason alone. In fact, the one I received already had half the package cut away as if someone had given it up and returned it rather than bloody his fingers.

Pretty nice system but needs to be improved
This seems like a good system so I bought one. It provides a swivel base and a quick-release bar clamp. Upon mounting on a table, it does seem to provide a very verstatile way to hold various objects. However, two problems soon become evident. First, the whole system has a lot of play in it, so it is not really designed for any activity that would exert more than moderate force (such as hack-sawing) on the object. Secondly, there is a defect in the design that when you clamp the system onto a table, the release on the bar clamp is practically touching the table, which makes it rather cumbersome and hard to swivel the clamp or tighten or loosen the clamp. Back to the drawing board.

Really Great Idea!!!
I was skeptical about this clamp/spreader until I got it home! It is amazingly versatile! If you dont understand what I mean click on the picture to see how this clamp works!

The odd dome looking piece on the under side of the clamp is used to attach it to the side of a bench. And when you tighten this down to the edge of the table make sure you don't over tighten. Most people will tighten it as much as possible but thanks to the rubberized grips it just isnt necessary. Give it a comfortable hand tighten and it holds VERY securley! One note the bench must be no larger than 2 1/4".

The clamp itself can be removed from the bench attachment. While seated in the bench attachment you can swivel the clamp 360 degrees. And it does have positive detents for secure locking. You should also receive 2 sets of pads to be used on the clamp. One is smooth and the other has a no slip tread. Wilton also includes some project plans for variouse tasks. There are a few good ideas in there so check it out.

The depth of the Clamp is 3inches from the bar to the top of the rubber pad. And the jaws open up to about 13 1/2 inches. ... Read more

Features

• Clear wire reinforced hose
• 4" by 10 feet

Reviews (4)

Pricey but works well
Yes, it is expensive for hose. This does work really well though and it probably some of the best hose on the market...... Very flexible (some types are stiff) and the ability to see into the hose is (nearly) priceless! Had something get stuck in mine last night. Would have never known until it became a bigger problem if I could not see that little piece of wood!

You get what you pay for!
This is the best hose that i have found to date.It does cost more money but it performs well.I have two sets.I also have the 6" hose.It is best to use the wire style clamps to retain the hose to the machine or dust pipe.I have seen these hose used on big molders with six heads.Hope this helps your choice of hose.
Thanks, Weyer Service

Can it be cost justified??
In comparision to the counterpart black hose, the only advantage I can think of is that you can see thru this hose to easily identify where any possible clogs are located. With the black hose you have to use trial and error, and possible take the entire DC system apart to find the clog. With the clear hose, you can see it and go right to the problem spot. Is this worth almost double the price of a black hose?

That can only be answered by the user. I'm using the clear hose only off of machinery where large chips are make, my lathe and bore machine (drill press). Other than that, I opted for the cheaper black hose. I also have those two machines located the closest to the dust collection machine, so the hose length, and chip travel, is the least possible.

A must for a dust collection system
The quality is great - 5 star. This price is ridicules - 0 star. Check another source. Read Controlling Dust in the Workshop by Rick Peters. I have used about 60' of this my workshop to connect each of my power tools to my metal duct system. ... Read more