Features

• Includes 4 tool-free mounting knobs for attaching and removing benchtop table
• Brings RA 1180 table height to 38-1/2"
• Very sturdy design

Features

• Includes dust collection hoods for edge-forming and flat surface applications.
• Hose port angles maximize collection efficiency, keeps hose out of the way
• Includes vacuum hose adapter for use with 1-1/4", 1-1/2" and 35 mm hoses
• Includes tool-free mounting hardware for each base.

Reviews (1)

Dust extraction that works
I've purchased this and put it on my router and did some plunge routing. 70 % of the chips were captured and the clean-up was considerably less. I also noticed that my dust mask seemed to plug up less. It apparently get the fine dust too. For the cost it's worth the effort. The black hose adapter converts the hose from metric to english. I would recommend that you convert to a larger hose fairly quickly because the small hose cause a significant loss in vacumm the longer it is. ... Read more

Features

• For Table and Miter Saws
• Patented C3 Dyanite Carbide stays sharp up to 5x longer than standard carbide
• Fully hardened plate runs straight, improves speed of cut
• Anti-friction coating resists pitch/gum build-up

Features

• 5-pack
• 3-inch length
• 24-tooth
• Metal application

Reviews (2)

Great blades for sheet metal
These blades go great in my Bosch Progressor jig saw when its time to cut sheet metal. For this job, I always clamp the metal down to a piece of scrap plywood then cut through both metal and wood with one of these blades using a mid-range orbital action setting on the jigsaw. By going slow and careful, this produces clean and fast cuts in the sheet metal without the vibration and noise you get when not using a backing material. I wouldn't put anything but genuine Bosch blades in my Progressor jig saw.

Just Did It
Just purchased my second Bosh jig saw not only because of it's endurance and smooth running capacity, but also because no other saw will use these Bosh blades. After 20 years of building I have never used a finer cutting blade. ... Read more

Features

• 19mm 15' Friction -fit hose
• Fits all Shop vacuums with 2 1/2-inch orifice

Reviews (1)

waste of money
I would recommend that you stay away from this product. Don't even think about buying it. If you are sanding buy the 1" adapter for your sander and look elseware for a vacuum hose. Poor design, low quality plastic materials make this product a complete waste of money. RUN AWAY! ... Read more

Features

• ServiceMinder light for preventive maintenance
• 10 amp motor; no-load beats per minute: 2,800 bpm
• SDS-Max bit system delivers tool-free bit changes with automatic bit locking
• Vario-Lock positioning rotates and locks chisel into 12 different positions
• 360-degree auxiliary handle provides a wide range of movement

Product Description

includes RS5 Reciprocating Saw ... Read more

Features

• 9 Amps
• 360° scroll collar - Allows user to get into hard to reach areas
• Quick change blade system - Easily changes blades with no additional tools
• Saw hook - Convenient saw storage between cuts
• Variable speed trigger - Easily control the rate of cut

Features

• Saw hook
• 12 amps
• Lockjaw Blade Change System
• Brute Drive System
• Swivel Cord

Features

• Vario-Lock positioning rotates and locks chisel into 12 different positions
• SDS-Max bit system offers tool-free bit changes with automatic bit locking, dust protection, and maximum-impact energy transfer rate
• Auto-Max variable-speed dial is designed to automatically ensure the maximum speed and power
• Constant Response circuitry provides soft-start and maintains constant speed under load
• ServiceMinder light indicates when preventative maintenance is required

Features

• 26 lbs
• 8 inch diameter. semi-pneumatic, ball bearing wheels
• Rugged 1 inch diameter. all welded steel frame
• 4 sockets hold any 1 1/8 inch hex insert tools
• 46 1/2 inch high, 14 inch wide

Reviews (1)

Solidly built
I was impressed by the quality of the construction. It doesn't have the wobbly wheels I've seen on some hand trucks. The only reason I didn't give it a 5, is because I bought it to use as a garden cart, thinking the holders on the back would be perfect for small garden tools. That proved to be true, however it was not clear from the picture or the description that there is a metal post that extend up in the center of the portion that would normally be slid under the edge of a piece of furniture. Because I didn't get it to move furntiure, it was easy enough to overcome this particular feature, but it would have been nice to know before I bought it. ... Read more

Features

• 5 per package
• 3-inch length
• 20 teeth per inch
• T-shank blades
• For fine finish, veneers, and laminates

Reviews (2)

Is there another choice?
These are the only blades smooth enough for any kind of finish carpentry. The straight teeth make all the difference in the world. From coping crown to the most extreme scrolling cuts, these blades are perfect! I haven't bought any different blade than these for years. If I can't find them in stock I'll do without rather than buying anything less than the best. If thinking about purchasing jigsaw blades, buy these. The only thing I would like to see from Bosch is the same blade a 1/2" longer. But you can't have your cake and eat it too!

Great blades!
I am a contractor and have been using these blades for years. They make extremely smooth cuts in ALL woods from pine to rock maple...even MDF ... Read more

Features

• Fits Bosch Vaccum model 3931
• Prevent static shock and cling
• Anti-static
• locking

Features

• 5 amps
• 2 speed (25,000 & 30,000) RPM
• CLIC design depth adjustment

Features

• Peels away frozen ground in layers

Features

• Cut 13/16 to 2-5/16-inch
• 5-pack
• 4-inch length
• Progressor metal blade
• Teeth milled and side set

Reviews (2)

Great for the first few cuts, but then . . . .
The first time I put these blades in my BOSCH jig saw, I thought how wonderful it was that BOSCH had created a blade that cut quickly, cleanly and slightly filed simulateously. Well, they do but they really only " file " the cut the first few cuts depending on the hardness of metal. I was cutting 1/8" mild ferrous steel and was amazed initially, then just pleased. My opinion is that if you have to make a few* good clean cuts the first time, and can't file/grind or just dont have the time or desire to do so, this is great choice. However, I feel for less money the standard BOSCH metal cutting blades cut just as well, and last a little longer.So these would be a five, if the abrasive edge coating held up a bit longer.

Super Blades for a Super Saw!
I used one of these blades in my 1587AVSP while I was modifying the dash of my '83 Toyota Pickup to accept a new stereo. It cut nice and clean - no filing was necessary. It was also very easy to control while making the cuts. I had to "run the edge" of one side to make the hole about a blade width wider - no problem. I even had to saw through a thicker frame member behind the dash, basically freehand, nowhere to rest the baseplate of the saw. I just hit the piece with the blade at full speed and went right through it, just where I marked it.

These are highly recommended, especially if you run them in the Bosch saw! ... Read more

Features

• Reinforced armature windings - protects motor against abrasive dust and metal debris
• 15 Amps, 6,000 RPM
• Exclusive rotating handle design - rotates in either direction for hard to reach locations
• Lock-on/off switch - for extended use applications
• AC/DC capability - extends the versatility of the tool by working from DC outlets such as welders and generators

Features

• Fits Bosch models 3960 cordless drill/driver and 1645 cordless reciprocating saw
• One hour charge time
• Charges 9.6- to 24-volt batteries
• Checks battery status every second to prevent overheating and overcharging

Features

• For easist depth adjustment
• For use with Bosch 1617 and 1618 router series models
• Makes turning depth adjustment contrel extra-easy!
• Ideaf for use in router table.
• Easily press fits into router's fine adjustment control.

Reviews (1)

Expands your adjustment horizons
This knob is as much an extension of your existing adjusting knob as it is an increase in the overall size of the turning head. It snaps into your existing knob. Simply put, it makes it easier to make depth adjustments. First of all it is easier to find when under the table, and secondly it makes adjusting a little easier with such a large knob.
Not much else to say other than that. Highly recommended for your Bosch 1617 or 1618 series router. ... Read more

Product Description

includes 1617 Router, 1/4" S. R. Collet Chuck -- 2 610 906 283, 1/2" S. R. Collet chuck -- 2 610 906 284, 16mm Shaft Wrench -- 2 610 991 388, Collet Nut Wrench -- 2 610 992 417, Tool-Free Template Guide Adapter -- 2 610 991 370, 10 ft. flexible rubber cord, Chip Shield -- 2 610 991 389 ... Read more

Features

• 2.25HP /12 AMP Motor 8,000-25,000 RPM - Most powerful in its class
• Variable speed dial - For matching speed to workpiece and task
• Coarse and microfine bit depth adjustment system with resettable depth indicator
• Tool-free template guide adapter - For fast and easy template guide changes

Features

• Improved Schedule management, more timely and accurate updates of the project schedule means improved coordination among all team members
• Save money, pays for itself and device it runs on in less then a month
• Recover time, frees up at least one hour a day for the job site manager
• Improve vendor management, creates a paper trail for every task whether included in the original project plan or not
• Improves quality, better control of multiple job sites means things get done right the first time

Reviews (1)

Great software!
Punch List has been the single biggest improvement in our never-ending quest
to provide 100% customer satisfaction. The ability to track performance (or
lack thereof) by subcontractors has allowed us to clearly see who is doing
their job and who is slacking! Our customer satisfaction level has increased
dramatically since we started using Punch List. ... Read more