Features

• Solid steel, multi-directional exhaust cap
• Increased power for better driving of staples into hardwood applications
• Jam-Free magazine
• Molded rubber comfort grip designed to last longer
• Longer, narrower nose for increased visibility and ease in stapling corner blocks

Features

• 1,000/box
• L-shaped flooring cleats
• Nails 200 square feet of flooring per box

Reviews (1)

need more nails
If you are installing 2 1/4" hardwood flooring, one box(1000 nails) is needed per 100 SF - nailing every 6-8" ... Read more

Features

• 3/16 inch crown
• 1 inch leg length
• 5m/box

Reviews (2)

Floor Runner
these staples and the gun they are used in are the absolute best for installing Bruce "Natural Reflections" 5/16" flooring. What a time saver over gluing this product!

staples
We Love this product!Bostitch staples are the best .They outpreform any other staple in the market as far as holding power and setting capability. ... Read more

Features

• Rear exhaust port
• Nailer drives 1-1/4" to 2-1/2" 16 ga. finish nails
• Complete magnesium construction for ultimate strenght & extremely light-weight
• Use for: all trim/finish applications, cabinets, wood-working, staircases, arts & crafts, etc.
• Adjustable depth-of-drive dial

Features

• Multi-blow technology that virtually eliminates overdrives
• DC motor delivers 650 watts of power
• Drives 1 to 1-1/2-inch roofing nails
• Comes with two 20.4 Ni-cad batteries,one-hour charger, two canisters of 1-1/4" nails, manual, video, and case

Reviews (4)

6 Roofs per year
While I am not in the trade year round I have found this tool to be the answer to many of the challenges we face with safety and quality while on the roof.
This gun eliminates tripping hazards as there are no hoses or electric cords. This keeps the comprtessor off the roof so no hazard encountered while tring to get your equipment up to the work surface.
No overhead issue for the team on the ground because the grip pads on the top end of the gun really do stop it from sliding off the roof unlike other air guns that momentum of the hose carries the gun off the roof onto the teamn below.
Noise is much less of an issue than with compressed air. Communications from the ground up and down is easier. No noise to yell over.
I have read that you can reload the plastic containers the nails come in however I have not been able to find a manufactures note that would indicate that this is a safe practice.
Compared to the conventional Bostitch RN45B we are able to lay em down and nail em with equal speed and without fighting the hose all day.
The quality of our finished product is greater because there is no marring of the roof edge shingles from the air line rubbing against it. That is the customers line of sight and that matters.

...

If you are buying an air nail roofing gun. Reconsider and buy this battery operated gun.

Log Home Contractor
This is a fabulous tool. I use as many cordless tools as I can because I hate listening to my generator and compressor running all the time. Bostitch has made a top of the line tool with this one. The battery will lay about 2 1/2 square of shingles without a recharge and with two batteries one can be charging at all times so you never run out of power. The tool is loud but not as loud as a generator, it is a bit on the heavy side but much better than having that air hose in tow and the way it holds in your hand you barely notice the weight. You have to buy the nails in the in the plastic canisters which only cost on average two dollars more per box but if you are a real miser you can buy regular coil roof nails and reload the canisters. If you are like me and want to use cordless as much as possible and you do many roofs this is a great alternative to pneumatic. I have literally waited for years for this tool. . . thank you Stanley Bostitch.

No Hoses, No Jams, No Cords, No Overdrives, No Compressor
My construction class recently bought two of these nailers because our compressed air supply is too high pressure for nailers, so we use cordless or a seperate compressor. I have used a pneumatic nailer on five roofs ranging from small ticket booths to full sized play barns with flashing, felt paper, drip edge, and more. I was skeptical about a cordless nailer that did not use gas cells like a Paslode Impulse system, but I realized that it takes a lot less force to drive a nail through some shingles or a thin strip of aluminum than a 2x12 header. The jackhammer-style system takes some getting used to but it does not require padded gloves like a demo hammer. As for the nail cartridges, they are great. Our pneumatics constantly jammed from misshapened and bent wire-collated nails. The cartridges keep the nails in the correct shape.... This is the only roofing nailer you will ever need, just get some cartridges of nails, a couple of batteries, go up on your roof and start laying whatever is needed. This is a great innovation. If you dont believe me, try Tools of The Trade, they gave it a special award for innovation

Heavy, slow, loud and you have to buy their special nails!
I thought the basic concept of a cordless nailer was great, but this thing makes no sense.

It does not use gas cells like the Paslode. It is multi-blow, kind of like a jackhammer or a rotary hammer. It actually hits the nail a bunch of times before it drives it in unlike the paslode nailer that drives it in one motion. Seems to be really slower than an air tool. This makes it vibrate like crazy in your hand and it is wicked loud. Wear ear plugs with this thing.

It runs off of a 20.4Volt battery pack. The problem is that the battery is heavy and they dont have a drill or anything to run on the same battery. There is no way to spread your investment in expensive cordless tools. You also have to carry around another charger and battery and plug another thing in. THere is no cigarette lighter charger for the truck available either.

This thing is heaaavvvvyyy. My hitachi air roofing nailer weighs only 5-6 lbs i would guess but i think this thing is over 10 pounds. Way too heavy to be swinging around on a ladder or a steep pitch for repair jobs. The balance is a little weird to. Air tools are built to drive down into the shingle but this thing is shaped like a drill so you have a tendency to not drive the nail in straight.

The thing that really irks me is the fact that you cant use the same nail coils that you use in an air gun. You actually have to buy nails that are specifically for this tool and dont work with anything else! So that puts you at risk for them to jack up the prices on the nails once you are hooked on them. The nails also come in these little plastic individaul pouches. Im no freaky enviromentalist but i dont like wasting all that plastic and i dont like cleaning more junk off a jobsite at the end of a day.

HEAVY, LOUD, SLOW AND YOU HAVE TO BUY THIER NAILS. ALL THIS FOR ONLY ... GET ONE TODAY! ... Read more

Product Description

Bostitch N88RH1PN Framing Nailer with Palm Nailer ... Read more

Features

• Plastic Collated
• 21 degree - Round Head
• Works in: N88RH & N88RH-2MCN

Features

• Side load magazine with visual reload indicator
• Drives 5/8" - 2" 18GA Brads
• Tool free adjustable depth setting
• Tool free adjustable exhaust
• No-Mar tip w/ on tool storage

Features

• Pistol Grip Blow Gun
• 3/8" x 50' Heavy Duty PVC
• 1 MPT 1/4" Quick Connect Coupling, 1 FPT 1/4" Quick Connect Coupling, 1 FPT 1/4" Quick Connect Plug, 1 MPT 1/4" Quick Connect Plug
• Teflon tape
• Pneumatic tool lubricant

Features

• Uses STCR5019 series Power Crown™ staples from 1/4" to 3/8"
• Long reach knuckle saver handle with non slip grip
• Die cast frame and hardened components for extreme durability
• High Capacity bottom load magazine
• extra wide foot plate helps prevent tearing and marring substrates

Features

• Powerful
• Compact design
• One hand operation
• Ideal for tacking and batt insulation also good for felt and sign mounting.
• Accepts 1/4 inch and 3/8 inch bostitch staples

Reviews (3)

Good product
I purchased this item for a carpenter that I sometime work for. He gave me his Arrow hammertacker becuase it always jammed.Your product has been jam free since he has had it (2 years). I used his old stapler today while working off of a 28 foot ladder. It worked so well that I threw it to the ground and decided to order 2 of them , one for me and one for him (he left his on a job).

Simpler is better
I've owned every slap hammer stapler you can imagine. This is one of my favorites. It is so simple.If you like jams this tool is not for you. It just doesn't jam up like the others that are more complicated. I refuse to buy any more of the arrow and duo-fast staplers. I have some of the 100.00 Stanley H2B's but they are just gathering dust. I prefer these cheap little slammers any day of the week.

Bostitch does it right
I think the real selling point of this one is the holster. For contractors (especially roofers), a holster is a necessity for the job -- and how often do you see a retailer that sells slap-tacker holsters? And you can trust the quality of every tool Bostitch puts their name on. I'd say this one is a keeper for anybody in the market for slap-tackers. ... Read more

Features

• Includes all needed fittings and hose to be ready to go to work
• Oil Free 2 hp 6-gallon compressor (CAP2060P)
• 2-1/2" 16-gauge finish nailer (SB1664FN)
• 300 inch/pounds of driving power and convenient depth control
• Directional exhaust, lightweight aluminum housing, rubber foot to protect finish, and comfortable rubber handle grip

Features

• Includes screwdriver, wrenches and carrying case
• Aluminum housing for job site durability
• Bottom load magazine for fast-loading and accurate fastener placement
• Narrow nose for accurate fastener placement
• Compact and lightweight for easy maneuverability

Features

• Quick released nose for clearing jams
• Drives1" - 2 1/2" 16 GA finish nails
• Tool free adjustable depth setting
• Tool free adjustable exhaust
• No-Mar tip w/ on tool storage

Features

• Round Head
• Works in: N62FNK-2

Features

• Plastic Collated
• 21 degree - Round Head
• Works in: N88RH & N88RH-2MCN

Features

• 3/8-inch staple
• 5,000 per box

Reviews (1)

powercrown staples
"Powercrown" staples performed exceptionally well for all stapling jobs. Have used them for everything from "Tyvec" to insulation and have had exactually 0 problems. When used in the "Slammer" they give no problems and feed well. ... Read more

Features

• Bostitch 5000 ct. 1" Staples for S150SLBC-1 Cap Stapler

Features

• No mar tip
• Oil free
• Lightweight magnesium housing
• Ultra quiet rear exhaust
• Adjustable depth control

Product Description

Fits Bostitch Tools N80CB, N86C, N100C, N100CPP Fits Competitor Tools DuoFast: CNW-75 Hitachi: NV83A (1-1/2-3-1/2) Makita: AN901 (1-3/4-3-1/2) Max: 890C Paslode: F275C/P275C (1-1/2-2-34), F325C/P325C (1-1/2-3-1/4) Porter Point Style Diamond ... Read more