Features

• Fits Delta 14" band saws
• Provides dust collection for band saws
• Replaces dust spout on band saw
• 5" diameter outlet
• Galvanized sheet metal for durability

Reviews (2)

Could have been easier
The collector worked good after I got it installed.Some simple instructions would have made it a lot easier.I had to drill out a hole and do some bending to make it fit,but it was worth it.

Just what the doctor ordered
This is the perfect adapter to replace the standard plastic outlet the bandsaw came with with. Easy to install, the bandsaw is now a perfect fit for my dust collector. ... Read more

Features

• Adapts Delta Unisaws for dust collection
• Allows you to maintain a cleaner, safer work environment
• Installs easily over opening under motor cover for quick set up
• Outlet fits 4-inch dust collector hose for efficient chip collection

Reviews (5)

HOME WOODWORKER
THIS IS THE ADAPTOR YOU WANT IF YOU HAVE A 4" DUST COLLECTOR. THE PICTURE IS MISLEADING BECAUSE THE DUST CHUTE IS NOW OFFSET TO CLEAR ANY MOBILE BASE PROBLEMS YOU MIGHT HAVE HAD. ITS A LITTLE OVER PRICED FOR A PIECE OF SHEET METAL AND A STANDARD PLASTIC DUST CHUTE ( PART # 406-12-026-0001). IT WOULD BE MORE REASONABLE FOR AROUND 20 BUCKS, BUT FOR WHAT DELTA WANTS FOR A NEW UNISAW IT SHOULD BE INCLUDED.

Just right, but could be a bit sturdier
This works great, and with my mobile base. I would suggest a 90-degree adaptor with a 6" length of hose to make it a bit easier to hook up to the rest of the system.

Requires the removal of the lower shelf (at least so far), but I don't really use it anyway.

Not recommended with Delta mobile base
I do not recommend this dust connector in combination with Delta's mobile base. I had two issues: The dust port is too close to the swivel caster and interferes with the hose connection. The right side exit required a tight radius bend of flex hose to get to my left side duct collection pipe. I found rear exiting 50-224 (with 5" opening) to be better.

Works for right-tilt Unisaws, too
The editorial review of this item is a little misleading. Yes, I'm sure it works on left-tilt saws, but it fits perfectly on my right-tilt as well. The label on the box just says "dust connector for Unisaws". This is the one to get if you run home shop-type 4" dust collector lines.

Built solid, installation a snap
Attached directly to my left tilt unisaw with no problems at all. Assembly was very quick (a few minutes). The plate that attaches to the cabinet is very rigid and solid. The 4" OD adaptor is more typical for a home workshop than the 5" OD alternate I have seen else (the 5" version that I have seen is just flimsy sheet metal and costs about $50). I would recommend this dust collector attachment for any home workshop that has a unisaw. ... Read more

Features

• Provides dust collection for Series 2000 Contractor's Saws
• Attaches beneath table saw
• 4" diameter outlet
• Constructed of high-impact plastic

Reviews (4)

Good, but you need more
The dust collector plate is simple enough to install. On a saw already set up, it takes about 30 to 40 minutes. If the saw was new and this was installed as part of the assembly process, it would add about 10 minutes.

Others mentioned the gaps on the sides. I closed them up with duct tape. This still leaves the back of the saw open. Contractor saws are not easy to set up for dust collection for this reason. I used a pice of 1/4" plywoods and closed off most of the back. I cut a slot for the drive belt and the motor support, then mounted it with two sheet metal screws. It goes up about 2/3 of the opening so air can be drawn it for proper dust collecting. When tilting the saw, the enclosure must be removed though, until I come up with a new and better method.

Overall, it works well enough and it better than some "universal" systems.

Almost there!
Delta specifies this one for the 36-431 saw and it installs quickly but it still leaves a gap about 3/8 inch wide on both sides which causes sawdust to escape. I really feel that the design of this unit could be improved to create a better air flow (such as a swirling effect, maybe) in the saw chamber to get more of the sawdust. Although it gets nearly all the sawdust with a 50-850 1200 cfm dust collection system, it leaves just enough to require more cleanup after the cutting is finished.

Disappointing
Bought this attachment for my Delta contractors saw and was disappointed. It is farely easy to install but once it is in place it leaves a crack about one half inch wide along each side running from the front to back. There are two heavy steel spacers that go on each side to fill in the void but they are not wide enough for some reason and the crack is just wide enough for saw dust to fall through to the floor. This crack serves no purpose that I can think of and I plan to cover it with duct tape or something to see if it will solve the problem.

Not a perfect fit
The picture (here) is not complete. There are 2 metal flanges that get connected to the bottom of the saw using the existing screws for the stand, then the heavy duty plastic dust connector is held to the flanges by sheet metal screws. Installing it is pretty straight forward, except that there is a gap about 3/8" between both sides of the dust collector and the saw case, allowing some saw dust to fall to the floor. ... Read more

Features

• Fits Delta and other brands of radial saws
• Provides dust collection for radial saws
• Attaches to base frame of saw, to the left of the column
• 5" diameter outlet
• Galvanized sheet metal for durability

Features

• 5 micron replacement bag for model 50-840 dust collector
• Provides maximum filtration of airborne particles
• Traps particles down to 5-microns
• Can be used for top or bottom bag replacement

Features

• Mounts to floor to provide easy collection of wood dust sweepings
• 4" outlet for use with standard hoses
• For use with central dust collection systems
• Low profile design restricts larger objects for safer collection

Features

• Fits models 43-370, 43-372, 43-373, 43-375, 43-379, 43-384, 43-385, and 43-386
• Adapts Delta Heavy-Duty Wood Shapers for dust collection
• Allows you to maintain a cleaner, safer work environment
• Installs easily over opening under motor cover for quick set up
• Outlet fits 5-inch dust collector hose for efficient chip collection

Features

• Fits Delta DJ-15 and DJ-20 jointers
• Provides dust collection for jointers
• Attaches to jointer cabinet, covering factory installed chute
• 5" diameter outlet
• Galvanized sheet metal for durability

Reviews (3)

Poor Design
I agree with the other reviewers. This is a poor design, obviously an after thought. I have DJ-15 that is a few years old. I have no intention of drilling holes in it. Also, the outlet is 5 inch, not 4 inch. I sent mine back, I plan to take the suggestion of the other reviewer and tape on a plastic one. Delta makes then for their newer 6 and 8 inch jointers.

PLEASE!
Come on Delta, you can do better than this!

If you plan on buying a DJ-20, buy an inexpensive square table saw dust connector (about 1 ft. x 1 ft.), use 1 in. double sided foam tape (like the kind used to hand posters and such), and stick the connector to the side of the DJ-20. You won't be forced to drill any holes in your new expensive jointer, and you'll get a perfect seal around the connector.

Requires modification to router
My wife ordered this for me, since it was on my wishlist. She had purchased my Delta DJ-20 8" jointer from Amazon for my birthday, nice wife! Anyway, this dust connector is mounted with the included screws, but there are no holes in the side of my DJ-20 jointer. I'm going to have to drill holes in the side of my expensive jointer to use this connector. Would have preferred a simpler solution. ... Read more

Features

• Universal design fits many brands of jointers
• Fits 8" jointers to provide proper airflow for efficient dust collection
• 4" diameter outlet for use with standard hoses

Features

• Two-year limited warranty on machines, parts, and accessories
• Traps dust at the source, before it becomes airborne
• Steel top with rubber grommets to protect workpiece and provide a non-slip grip
• Reusable pleated filter is encased in metal tray for durability and easy cleaning
• 31" x 31" table top with retractable dust curtains

Reviews (1)

Solid and Huge -- as expected from Delta
I am setting up a REAL basement workshop for building furniture and needed a top notch solution to allow indoor sanding. This machine is what you would expect from Delta -- very substantial and solid. Decent air flow, combined with the curtains, directs the dust to the removeable dust filter. At 31" by 31", and with the moveable dust curtains, you can handle almost anything in the realm of furniture. If you loved Erector Sets as a kid, you will also love assembling the 50-855 -- with some 75 sets of bolts, nuts, and washers -- straightforward, but 1 to 2 hours to set up. Overall, a great addition for any woodworker who recognizes the importance of dust control! ... Read more

Features

• Adapts Delta 37-070 Bench Jointer for dust collection
• Allows you to maintain a cleaner, safer work environment
• Installs easily over existing dust chute for quick set up
• Outlet fits 4-inch dust collector hose for efficient chip collection

Reviews (1)

Doesn't adapt so well
Delta usually puts more quality into thier products. I had a bit of trouble trying to get the screw holes on the dust adapter to align with those of the jointer. Once attached, the fit was less that tight, which caused some shavings and dust to leak out when used with my shop-vac. When I hooked it up to my Jet 1100CF vac, these problems seemed to go away. ... Read more

Features

• Adapts Delta 22-540 12-inch Planer for use with 50-179 Dust Collector
• Allows you to maintain a cleaner, safer work environment
• Installs easily in place of existing dust chute for quick set up
• Outlet fits 4-inch dust collector hose for efficient chip collection

Reviews (10)

Bad Instructions, Good Product
The editorial review @ Amazon states that this is a REPLACEMENT of the chip chute... THIS IS INCORRECT! The poor quality copy that serves as the instructions never states that you remove the existing chute--thanks to one of the Amazon reviewers for getting this right! It fits over the existing chute. In this configuration, the dust hood works well and is structurally stiff. Mine fit on the planer with no problems or modifications.

As far as performance is concerned, I even forgot to turn my dust collections system (1100CFM) on for one pass and the only chips that came out were towards the front of the machine; with the dust collection turned on the dust chute was every bit as effective as I thought it would be: almost no chips or dust in the work area.

Bad Fit for the price
Sheet metal had to be rebent into the proper position to get it to fit. About a 45 minute job.

A little flimsy for Delta
The metal dust hood is a little flimsy for what I usually expect from Delta. The instructions were photocopies of bad photocopies and were nearly useless. The hood goes over the existing chip chute, it does not replace it. This was not clear in the instructions. If you remove the existing chip chute to add the dust collector, it leaves the blades exposed. However, it is easy enough to see how it fits on the planer. The holes, etc fitted well. It works well and collects most of the dust and chips. I hessitated before buying based on other reviews. I think it works well for people using a dust collector with plenty of air flow. It probably does not work well if you are trying to use a shop vac. Overall, it's OK for me. I would not have minded spending a few more dollars if the quality was better.

product is terrible
after receiving this dust hood, and trying to install it obviously there must have not been very much thought put into the design. when following the instructions you still have to twist and bend the hood to make it fit properly. even still i had to add a bracket to the left side, drill a hole and use a tap to make threads in the machine to properly secure the dust hood. if this product wasn't a gift i would have returned it and made my own out of aluminum stock utilizing the existing dust shute. i would only suggest buying this if you feel like playing around with it to get it to fit. any questions email me

Mediocre product
I agree with some of the other reviewers--the thing just doesn't fit very well. Not all the holes line up so you really have to twist it in order to get the screws in. Once assembled, it works OK. I have a 2 hp collector, so nothing ever clogs, but it still only gets about 80% of the chips, so that leaves 20% all over the place that you still have to clean up. That said, you really don't have any other choice (except make your own), and over the life of the tool, it will save you a lot of sweeping. It's just that it would have been so easy to make it better... ... Read more

Features

• Fits most contractor-style table saws to provide dust collection capability
• 4" outlet for use with standard hoses
• 12" x 12" base fits smaller saws

Features

• Allows use of dust collector in height restricted areas
• Replaces top dust bag on Delta 50-852 and 50-853 dust collectors
• Designed for a custom fit, easy to install
• One bag included, buy two to replace both top bags

Features

• Two-year limited warranty on machines, parts, and accessories
• Traps dust at the source, before it becomes airborne
• Steel top with rubber grommets to protect workpiece and provide a non-slip grip
• Reusable pleated filter is encased in metal tray for durability and easy cleaning
• 24" x 24" table top with retractable dust curtains