Features

• Easy carry case
• 10-piece quick change system
• 1/4" hex adaptor
• Compact screw guide
• 4-hex shank drill bits

Features

• Dado insert for Hitachi model C10RA2 10-inch portable table saw

Product Description

Hitachi 13320 For use with NV65AH. 13320: 2 1/4" x .092 Ring Shank Electro Galvanized ... Read more

Amazon.com

Pipe, rebar, and shaped steel are no match for the power of this Hitachi cut-off machine. A powerful 15-amp motor runs the wheel at 3,700 rpm with no load. Angle cutting requires just a little adjustment to allow cuts at 45, 60 or back at 90 degrees. At 90 degrees, its maximum capacity is almost 4 inches high and 6-1/2 inches wide. The vise at its widest is 9- 9/32 inches. It comes with a reinforced resinoid cut-off wheel ready to tackle the toughest materials, and changing out a worn wheel is a snap. All the maintenance it requires is eventual brush replacement and regular lubrication. It's a workhorse that will serve the contractor well.--Kris Jensen-Van Heste ... Read more

Features

• Hitachi exclusive 5 year warranty
• D-handle for easy operation
• locking vise system for quick feeding and easy tightening
• Powerful 15 amp motor
• No load speed: 3,700 rpm

Features

• Variable Speed dial-in switch
• 3/8" Key-less chuck
• 6 Amp Motor
• 108 in-lbs torque
• 0-2,500 RPM

Product Description

Hitachi 985233 1 1/8" Hex 5 1/2" x 20" Clay Spade ... Read more

Features

• 5 1/2" Clay spade
• 1 1/8" Hex Shank
• 20" long

Features

• 1,180 feet per minute in low and 1,475 feet per minute in high
• 8.7 Amp motor
• Labyrinth dust free design
• 2 speed motor
• Designed for flush sanding

Reviews (3)

It is great
I have enjoyed using this sander,I am confused about a stand that allows you to use it for small parts.Overall, I am very pleased with this tool

Best Buy - American Woodworker
From AW #79 (April 2000), which can also be viewed online at the American Woodworker website.
HITACHI SB 75 is an excellent 3 in. x 21 in. sander.It has the highest amp motor in the group, the dust bag works well and it has two speeds.It would be handier if the low end of the speed range were lower, but it works OK.A weak spot is the belt-change lever.It's pointy and hard to pull.Get the bench stand to really make this one versatile.
8.7 amps, 1180/1475 FPM (feet per minute), 10 lbs.

Inadequate
This unit looked like a 4" x 21" BELT SANDER. THE 3" SANDING BELT HAD OVER 1" OF SPACE LEFT ON THE SURFACE OF SANDER SIDE TO SIDE. THAT MEANS YOU WOULD NOT KNOW WHAT AREA THE SANDER WAS SANDING.If it had a 4" belt it would look OK.
Looks like someone made it with left over 4" sander parts. VERY POOR DESIGN. ... Read more

Features

• Long run time
• Consistant discharge
• 18 volt battery
• Ni-Cad
• 2 Amp/hr

Features

• Fits NT65MA and NT65MA2
• 2 1/2-inch
• 15-gauge finish nails
• Electro galvanized
• 3,000 count

Features

• 8-1/2-inch blade
• 24 teeth
• Carbide tipped

Features

• Heavy duty motor
• 1 9/16" Spline
• EVS
• Cybernetic Design
• Cushion grip

Features

• Longer run time
• Fits all Hitachi 18 volt tools
• 18 volt battery
• 3.0 Amp Hr
• Nickel Metal Hydride

Features

• Fits NV50AP2
• 2" x.083 RG
• Plastic Cap
• 2.8m Count
• Electro Galv

Features

• Hitachi exclusive 5 year warranty
• 3.7 Amp motor
• 4 cutting edge blades
• Compact and light 3.7 lbs.
• Cuts 16 gauge steel

Features

• 6 Teeth per inch
• 3" long
• Carbide Blade
• Fiber Cement

Features

• Heavy-duty body casing
• High performance fan cooled motor
• External brush access for longer tool life
• Tool-less blade retainer for quick blade change
• Anti-vibration and comfortable soft-grip handle

Reviews (1)

.i hate jap crap
its like a toyota its dependable if an old lady is using it, but when someone who wants to work it gets a hold of it its trash in a week if you want my advise buy a bosch or a millwaulkee even a dewalt or porta-cable would be better ... Read more

Features

• Ni-cad charger
• 1 hour charge time
• Charges EB1414 and EB1412

Features

• Fits NT50AE
• 18 guage
• 5m count
• Electro Galv

Features

• Fits NT65MA & NT65MA2
• 15 guage finish nails
• Bright
• 4m Count

Features

• Electronic variable-speed
• Drill and Hammer/Drill modes
• Side handle and depth gauge
• 30-day satisfaction guarantee and one-year warranty on parts and labor