Amazon.com Review

When it comes to jointers, there aren't a lot of differences among the leaders in the market. Like other manufacturers, Jet uses heavy-duty cast iron in the fence, jointer base, and infeed/outfeed tables and offers a three-blade drum and built-in 4-inch dust port. Their design, however, features a couple of innovations that changed our "jointers are jointers" mindset. While the infeed tables in other models can only be raised or lowered with a rod or lever system, this machine's design allows you to adjust both of the feed tables by rotating smooth, industrial-style hand wheels. This feature lends itself to easier tapers and gives you more control when you need to take off precise measurements, like 1/64 of an inch, a setting that can frustrate woodworkers lifting the arms up or down on other machines. The fence glides extremely smoothly throughout its range of motion and tilts both ways, but, where other brands offer fixed stops only at 45 and 90 degrees, Jet's jointer adjusts to quickly reproduce multiple cuts at any angle you find necessary. Driven by a 4,850 rpm, 1-horsepower induction motor completely encased in a welded steel stand, this jointer comes prewired for 115-volt outlets and can be converted to run off 230-volt sources. As a final touch, Jet designed the industrial start switch with holes behind the button for locking with a readily available Master Lock to keep coworkers or family members safe from accidental injury. --Justin Paul ... Read more

Features

• Built-in ledge for cutting rabbets
• 1 hp, single-phase, 115/230-volt motor
• 46-inch cast-iron bed with precision-machined finish ensures accuracy
• Fence tilt two ways and features 90- and 45-degree positive stops
• Easy-to-use handwheels accurately adjust the infeed and outfeed tables

Reviews (32)

Excellenter Jointer for the money
I purchased this Jointer a week ago and rec'd it yesterday and promptly began setting it up. I run a small custom furniture and cabinet business and rely on quality equipment to complete each job. I'm a fan of both Jet and Delta machinery and own some of each so it was a tough decision on which unit to purchase. With the little testing that I've done thus far the Jet performs very well and I'm quite satisfied with my choice. My decsion towards the Jet was merely due to price and the features of having the hand wheels on the front vs. underneath the table. Other factors were the favorable reviews both on Amazon.com and magazine reviews.
Some features that I see could improve upon this tool would be a rack & pinion fence (the fence slide is not overly smooth) and the power buttons should be mounted above the table such as with the Delta. I'm not complaining as I was fully aware of all features before making my decision. If you're looking for a good quality Jointer then by all means this will satisfy your needs and I would recomend it to anyone. The only real downside is that an extra set of knives was not included but I would suggest replacing the stock ones with a set of Freud knives.

Good but flawed
I recently bought my new Jet JJ-CSX jointer. The fit and finish were excellent. I had chosen this model over the comparible Delta model. I liked the front adjustment wheels and the positive stops at 45 and 90 degress. This model was fairly easy to set up but I was missing some parts (screws) and had to call and have them shipped. I still have not received them. The tool performs well and the motor is very quiet and has plenty of guts to go thru some very hard lumber. The bad part is the snipe on almost every cut. All in all it is a fairley good tool and worth the money.

Fine little jointer
I researched 6" jointers and narrowed my search to the Delta or the Jet.

There's some disagreement as to the best way you adjust the tables and people have there favorite way to adjust the table and I listen to both arguments. I thought from the outset that I'd hate the lever and love the wheels.

The wheels on the Jet provide more precision while the Deltas lever seems more hit or miss, perhaps like having to tap a table saw fence in order to creep up on the adjustment.
When I went to try these two for myself I found the Delta to be extremely easy and smooth. Surprisingly accurate. I guess that may account for why many high-end jointers use a lever. The Jets wheels seem almost like a silly gimick in comparision. It's my personal first reaction when I tried them both, quite contrary to what I first assumed. I'm not saying there's a destinct advantage although it may seem so. It's my personal preference. Also note, that usually you leave the tables alone once you get them set.

Also, I originally liked the rack and pinion fence on the Delta. It's also higher than the Jets, but I haven't had any trouble at all with the Jet fence at all. I may have heard that the Delta fence might wear along part of the bed as you adjust it. With the Jets you have to lift it when you adjust it so you're not dragging it across the bed. That's actually a quicker action to perform. If you're joining edges you should move the fence to different positions across the cutter occasionally so you don't wear the blade in one set position.
The only benefit I could see with having this rack and pinion is sneaking up on a rabbet cut. Maybe the Rack and pinion fence looks more substantial, perhaps it's more solid if memory serves me.

Then there's the switch mounted higher on the Delta which I thought was a nice feature especially since I'm tall. Rather than the low cabinet switch on the Jet which seems very low.

When I finally saved up my money to buy a jointer I planned on going with Delta by a slim margin.
The Delta wasn't in stock and I was offered the Jet for $50 less plus a $50 rebate for buying the mobile base so I purchased it.

Assembly was very easy. the beds are heavy and you don't want to bang this around so it's to your advantage to get some help. Admittedly I did it all myself very carefully.
The beds were perfectly aligned with one another, no twist or bows. The motor is smooth, quiet with good power and no vibration.
Set up and alignments we're equally easy. My machine moved within the mobile base and I was taking only 1/16 - 1/32 cuts. It's the length of the board across the table and that downward push that can suddenly make that machine feel light when you actually use it. If I had the room or the extra money I think a nice 8" would provide enough heft as to overcome that but since I have niether here I am. If you can bolt it down permenantly that of coarse will take care of that. I've have learned to overcome this tendency on the mobile base, but it is a factor I have to be aware of when I'm joining.

Overall, I've used this machine so much now that i have wondered how I could have gone so long without it. It's been terrific.
So would I haved rather purchased the Delta now?
Some of the features that I once obsessed about aren't an issue once I began gaining practical experience using this machine and gained familiarity with all of its functions.
I saved some money as well, so no regrets.

Excellent Product
Shipping and packing were perfect. Machine was almost ready to go right out of the box. Instructions were easy to read and understand. A little cleaning with some kero, some minor adjustments to square the fence and set the infeed and outfeed tables and the machine was operating. Fit and finish were very good. What a joy to operate. Quite, smooth and the results are second to none. Highly recommend this machine to anyone considering purchasing a jointer.

So far, great edges
I bought this unit to replace a Delta X5 that had too many problems out of the box including a bad motor. The Jet instantly gave me a better feeling as I unpacked and assembled it. The machine was much cleaner and the finish much better than the Delta. The cuts were as good if not better than the Delta. Overall, the Jet was a better machine all around for me. ... Read more

Features

• Front and rear safety knife guide
• Extra long (9 w by 66-1/2-inch L) cast iron bed
• Three-knife cutter head
• 2hp, 1ph, 230-volt motor
• Easy-to-read infeed depth scale

Reviews (5)

LOOK ELSEWHERE IF YOU WANT GOOD SERVICE
I recently purchased the 8" jointer from jet after a good deal of research. When it arrived, the finish was o.k. It looked good, except for the front of the machine which was quite rough and had not been ground down after casting. Otherwise, it is a great looking tool.
I finally got it put together and wired up (about four hours total). I turned it on and it jumped to life. When I say jumped, I mean it started abruptly with a jerk, instead of smoothly and gradually. It also sputtered as it turned off. Upon further inspection and after smelling burning rubber, I opened it back up to have a look. There were black shavings all over the back of the machine, which turned out to be the belt.
I called the Jet service number. The guy told me to take apart the motor to tighten a set screw that was supposed to have been factory set. Very time consuming. That wasn't the problem. I called back and he told me to readjust all the pulleys and belts, which I had already done before calling. I did it again and that wasn't the problem either. He said he would send out a local Jet rep to look at it. Well that was four weeks ago. Not only was no rep sent out, the original service rep whom I had spoken with stopped returning my calls, would not answer repeated messages, and basically ignored me for a month. Finally, I got fed up and left a message in no uncertain terms that he needed to call me back that day because I needed this thing to work. It was jurting my business and it had been over a month. I said if they would not help me, then I wanted to return the machine. Only then did he get in touch with a local rep.
This guy called me the same day. I told him about the chunky motor and the black shavings. Guess what, he told me that the engine performance was normal and the belt could continue grinding itself away until it finds it's "natural position" - for up to a year. I find both of these things hard to beleive. At this point, however, because of the month of unreturned calls, it was apparently too late to get a refund or a new motor from Jet. You would think such a well known company would make more of an effort to satisfy it's customers.
I also own a Powermatic 66 saw, a Record lathe, a Craftsman bandsaw and a Rugged planer. None of the other tools in my furniture shop start or stop roughly at all, only the jet. I feel that I have now exhausted all of my options and am stuck with a tool that is slowly grinding itself away and service techs that could not care less. If I had it to do over, I would have gone with the Delta.

A great jointer with a couple of minor comments
Overall this is a great machine and I am glad to add this one to my woodworking tools. Putting it together is not easy, just the top weighs about 350 lbs. and you will need some help carrying this thing on top the stand. After securing in place everything should be easy with the exception of the belts which was not preset very well at least in my machine, so I have to loosen the motor mount base and slide for adjustment. It's like working in your car's motor. The manual wiring diagram did not match the motor wire color coding, so I have to call Jet for help, they are very helpful and will explain everything so you could hook it up. I don't blame them for not giving a male plug cord end since there's a lot of plug pattern to guess from. You will need to wire the shop for 240V. I am very happy with the machine, it works very well, and the long bed is really a good choice if you have the space.

Misma and Electrical
Make sure that you're manual's model# and picture match, and then, BEFORE you start putting it together, you need to check that all the wiring for your motor is finished and installed like it is in the instruction manual!!! It is a great tool, that performs and the fit and finish are excellent, BUT, ours was not wired as the manual said, so it got put together, and then we realized that there was no hardwiring (cord and plug),to the motor. For the price, I think that Jet should update the manual AND, at least,send the necessary cord and plug. I did not call Jet, so I don't know for sure why our jointer arrived without any wiring. The 4 stars is due to the above, the jointer itself has already proven that Jet was a good choice.

ONE STAR for POOR CRAFTSMANSHIP
I expected a lot more from Jet. Here are the problems that I had:

1.) the jointer had a CROOK at the end of the infeed table. That's unimaginable but it's true!
2.) the top of the cabinet had several DENTS on ALL FOUR CORNERS of its top. It looked as though someone used a HAMMER to shape out the corners of the cabinet.

I was so dissappointed with the finish of my jointer since I spent so much time and research debating on which one to buy.

That said, I'll be packing it up to exchange it for a new one.

I give "fit and finish" ONE star. I'll save my performance review for after I receive my replacement.

Great Support
Nothing but praise for Jet's support and quality of the product. I purchased the Jointer in December and finished my workshop in March. After I installed the Jointer, I realized that one of the parts was damaged during shipping. I called Amazon and they couldn't help me because it was past 45 days and referred me to two local repair shops. After many unaswered calls, I finally called Jet directly. They said no problem and shipped the replacement part.

Make sure you have someone to help you put the Jointer together, it is heavy. Directions were easy to follow and made sense. High praise for this product and company. ... Read more

Features

• 4 Inch Dust Port Included
• 3/4 HP Motor
• 46 Inch Long Bed
• 3 Knives in The Cutterhead
• Rabbet up to 1/2 Inch

Amazon.com Review

When it comes to jointers, there aren't a lot of differences among the leaders in the market. Like other manufacturers, Jet uses heavy-duty cast iron in the fence, jointer base, and infeed/outfeed tables and offers a three-blade drum and built-in 4-inch dust port. Their design, however, features a couple of innovations that changed our "jointers are jointers" mindset. While the infeed tables in other models can only be raised or lowered with a rod or lever system, this machine's design allows you to adjust both of the feed tables by rotating smooth, industrial-style hand wheels. This feature lends itself to easier tapers and gives you more control when you need to take off precise measurements, like 1/64 of an inch, a setting that can frustrate woodworkers lifting the arms up or down on other machines. The fence glides extremely smoothly throughout its range of motion and tilts both ways, but, where other brands offer fixed stops only at 45 and 90 degrees, Jet's jointer adjusts to quickly reproduce multiple cuts at any angle you find necessary. Driven by a 4,850 rpm, 1-horsepower induction motor completely encased in a welded steel stand, this jointer comes prewired for 115-volt outlets and can be converted to run off 230-volt sources. As a final touch, Jet designed the industrial start switch with holes behind the button for locking with a readily available Master Lock to keep coworkers or family members safe from accidental injury. --Justin Paul ... Read more

Features

• Built-in ledge for cutting rabbets
• Easy-to-use handwheels accurately adjust the infeed and outfeed tables
• Fence tilt two ways and features 90- and 45-degree positive stops
• 1 horsepower, single-phase, 115/230-volt motor
• 46-inch cast-iron bed with precision-machined finish ensures accuracy