Features

• Dust connector kit for use with a dust collector
• Includes the four most common accessories for Delta right-tilt Unisaws
• 8" carbide-tipped dado set for cutting grooves and dadoes
• Dado table insert for use with dado set
• Mobile base allows easy storage and portability in smaller shops

Reviews (1)

Ok Package But !!!!!!!
The Mobil Base works very well, however you need help in moving your saw if you purchased the Delta 36-960L. Someone has to support the out feed table. The dust chute works well. The dado set is ok, but you will need a set of shims to go with it.The only real problem is that if you purchased a left tilt delta saw (Delta 36-960L) the dado insert that comes with this kit is not the correct one. The Good news is one phone call and they will send you the right one. This is apearently a mistake in Deltas advertising dept. But as I said they corrrected it for me in about 5 days. ... Read more

Features

• Dust connector kit for use with a dust collector
• Includes the four most common accessories for Delta contractor's saws
• 6" carbide-tipped dado set for cutting grooves and dadoes
• Dado table insert for use with dado set
• Mobile base allows easy storage and portability in smaller shops

Reviews (1)

dado set review
I am not very impressed with the dado set. The outside blades cut a little deeper than the inside chippers,so when you use it to cut wide dado's it leaves grooves. I am impressed with the mobile base it works perfectly. The blade insert works well also. ... Read more

Features

• Platinum Pro blade is 1/2" wide by 105" long, for use with height attachment
• Includes the four most common accessories for Delta 14" band saws
• Height attachment increases cutting capacity from 6-1/4" to 12-1/4"
• Rip fence provides support for straight cuts up to 12" wide
• Mobile base allows easy storage and portability in smaller shops

Features

• Universal mounting system allows attaching to almost any table saw
• Three-point locking system assures fence is parallel to blade
• Built-in steel tape is accurate to within 1/64-inch
• Right and left side of blade ripping capacity
• Extra large 52-inch ripping capacity on the right side of the blade will handle even the largest jobs

Features

• Universal mounting system allows attaching to almost any table saw
• Three-point locking system assures fence is parallel to blade
• Built-in steel tape is accurate to within 1/64-inch
• Right and left side of blade ripping capacity
• Large 30-inch ripping capacity on the right side of the blade can handle most jobs

Features

• Provides a 30-inch cutting capacity for ripping plywood panels
• Fits Delta 10-inch table saws and a variety of saws by other manufacturers
• Unique locking system allows faster adjusting of the fence
• Fence body can be retracted and used as a stop for repetitive cut off work
• Fence body can also be flipped on its side to for cutting laminated materials

Reviews (7)

NO Instructions
Not sure yet. You didn't send any assembly instructions with the unit. I would appreciate it if someone would either e-mail me or mail me the necessary documentation.

Bill Scott
2917 Misty Ridge Drive
Norman, OK 73071-4118

Gain an extra 8 inches
I gave new life to an old faithfull delta cabinet saw by adding a 30inch unifence and sliding table.The installation of the sliding table requires removel of the left extention wing,which now the hardware for the sliding table interfears with the fence. I called Delta about this combo and they said to cut off 8inches of the fence guide rail which would keep the mounting holes and the tape rule right where they should be.I could not see cutting a 270$ fence. By relocating the mounting holes ( two 1/2 holes)down eight inches to the left my 30in fence became a 38in fence I purchased a new sticky back rule and put over top of the old one.The only problem is the fence table you have to add 8inches to it. I made mine so there was no problem, or you could buy the 72in table and cut it down. I love the combination cross cutting has never been this easy and safe. Good Luck.

Assembled to Sears Contractor Saw
Was pretty easy to install, you will need a 7/16th drill bit for some minor drilling. Template was easy to use and pre drilled holes on bottom of fence can be used for power switch. The fence is easy to adjust and is a welcomed change from the craftsman fence. A must have wish I would have purchased this a long time ago.

HASSLE FREE
I have this fence on my platinum edition saw and I'm very happy with it.I've tried other fence systems including biesemeyer and this one beats them all.Once assembled and adjusted it's soo smooth as it glides along the table and it clamps down rock solid.Unless your shop floor is 100% level(mine isnt either)you will need to make some kind of adjustment to either your saw stand or extension table.Delta does offer a real nice laminated table to fit your saw or you could make your own real easy. the legset you put under your extension table should have adjustable feet it's a whole lot easier to plumb it all up.The design of this fence allows it to be adjusted up or down front or rear independently of the carriage.I do recommend this fence for new saws or anyone looking to give an old saw new life. This ones a winner..

Upgraded Sears Contractor Saw
I ordered the 30" fence to upgrade my Sears 10" Contractors Saw. Installation was straight forward. I recommend buying the 30" extension table. The extension table required me to create some blocks under the supports to level the table with the saw. The installation was straighforward with no problems. When you upgrade you will have to remount the on/off switch. The Fence provides two treaded holes that you can use along with a 6" piece of right angle aluminum. Fence is dead on accurate and brought new life to an old saw. ... Read more

Features

• Provides a 52-inch cutting capacity for larger projects
• Fits Delta 10-inch table saws and a variety of saws by other manufacturers
• Unique locking system allows faster adjusting of the fence
• Fence body can be retracted and used as a stop for repetitive cut off work
• Fence body can also be flipped on its side to for cutting laminated materials

Reviews (2)

Delta is still the best!!
I have a 30 year old Delta Unisaw. I have used this saw day in and day out. I have upgraded my fence to a 52" Unifence. I can't express how much this has improved my table saw. You will not go wrong with fence. Delta is the Best!!

Great Unifence
This is a great product easy to install,easy to operate and gives excellent results. The quality of this product is second to none.If you do a lot of ripping I would recommend this fence. The two way fence is great for ripping thick or thin material be it veneer or whatever your saw will handle.I wished I had one of these years ago,what a time saver. ... Read more

Features

• Adds 8" x 27" working area to table saw
• Square corners match up to accessory table boards without modifications
• Cast iron for added weight and stability
• Fits Delta Unisaws and Contractor's Saws

Features

• Supports large, long, and wide workpieces up to 250 pounds
• Five 1-1/2" x 12" ball bearing roller keeps materials moving in a straight line
• Base has four leveling screws for stability
• Adjusts from 25 to 42-1/2 inches high to match a variety of table heights

Features

• Fits most contractor-style table saws to provide dust collection capability
• 4" outlet for use with standard hoses
• 12" x 12" base fits smaller saws