Features

• Includes dust collection hoods for edge-forming and flat surface applications.
• Hose port angles maximize collection efficiency, keeps hose out of the way
• Includes vacuum hose adapter for use with 1-1/4", 1-1/2" and 35 mm hoses
• Includes tool-free mounting hardware for each base.

Reviews (1)

Dust extraction that works
I've purchased this and put it on my router and did some plunge routing. 70 % of the chips were captured and the clean-up was considerably less. I also noticed that my dust mask seemed to plug up less. It apparently get the fine dust too. For the cost it's worth the effort. The black hose adapter converts the hose from metric to english. I would recommend that you convert to a larger hose fairly quickly because the small hose cause a significant loss in vacumm the longer it is. ... Read more

Features

• Hose port angle maximize collection efficiency, keeps hose out of the way
• Hood position can be adjusted according to the piloted bit bearing size.
• Includes vacuum hose adapter for use with 1-1/4", 1-1/2" and 35 mm hoses
• Includes tool-free mounting hardware for each base.

Reviews (1)

Save your lungs and cleanup time
This little collector works great if you have a powerful dustcollector or shop vac. A very nice addition to your router if you use it a lot and spend hours cleaning up afterwords. It also gets a lot more of the fine dust at the source before its air borne. ... Read more

Features

• Easily attached and emptied
• Keeps work area clean
• For model no. 4000 10-inch tablesaw

Reviews (3)

Not worth the price
Not worth the price you ask? It's only $11.00. True. Don't waste your $11.00. Instead plug a shop vac into the exhaust port of the table saw. The small exhaust port gets jammed easily and if that happens, forget collecting any dust in the bag. If the exhaust port stays clear, then I'd say I collect about 10% of the dust produced. Especially with MDF. What a mess!! I built a moble stand for the saw and folding stand so I push the whole thing out into the drive way and use it out there because of the mess it makes inside the garage.

The saw is great and I'm very happy with it. I gave it 4 or 5 five stars in my review of the saw itself. But this collection bag is pointless. Save your money and spend it elsewhere.

Until I get my dust collector for all my tools, I use this bag on my DeWalt 2-speed planer where it works great. I empty it frequently, but that's a planer for you.

Bag Works as Expected
This is a simple bag that's about 12" by 30" inches or so with a wire clip that goes around the dust port. It works pretty well in that everything expelled from the dust port goes into the bag, which is emptied by just shaking the sawdust out through the same opening.

All together it catches about 80 percent of the sawdust - about what one would expect. The cloth is a thin synthetic and there is no zipper or velcro to make it easier to empty.

Get Three
The 4000K must rank way up there with the world's greatest sawdust dispersing tools. My Dust Collector was tried and failed. It is now gathering dust (pun intended). It is a nice thing to look at and seems to fit OK, but you wouldn't want to depend on it. I can't be certain with actual efficiency rating, but I'd be shocked if you could prove it captured even half the sawdust. Get a REAL dust extractor with enough vacuum to suck the paint off the tablesaw stand, and you will be sure to collect 90% of the saw's by-product. The other 10% will be up your nose unless you wear a paper mask. :-) But real men eat sawdust, don't they? ... Read more

Features

• Attach to vac and clean the dust from your shop
• Crush proof
• For use with planer vac connector
• Accessory for Bosch routers 1613EVS and 1615EVS, and for Bosch drill kit 1005VSRK

Reviews (3)

Don't get hosed with other attachments
If you intend to use this system with other attachments - make sure they are the fine dust generating type. The hose causes too much vacuum loss and won't pull larger chips away and it will plug up. The hose is very flexible and doesn't crush but it can't be shorten because of the molded in fittings. It's small diameter and flexibility componds the vacuum loss when you use it.

This system can NOT be used successfully with a router or circular saw dust collection attachment. It probably will work ok with a jig saw, palm sander or belt sander.

a must have / good hose!
You won't get "hosed" with this acessory. I like it to attach the sander to the shop vac and it keeps dust to a minimum in the shop. This is a must have if you do alot of sanding!

I just orderd my second one
I have had one of these hoses for the last 6 years. It has performed very well, it really doesn't crush, simply folds over and then opens right back up. It is ideal for use with a shop vac and sander for keeping the shop dust level down. It's light weight makes it easy to use. ... Read more

Features

• Powerful 1300 Watt - 11 Amp rating
• 4 wheels swivel 360° for optimum mobility
• Sophisticated Air Clean II technology with Microsan exhaust filter
• Variable suction control
• Roller nozzle with carpet lifter