Features

• Comes with mounting hardware and instructions
• Requires no tools to install or remove
• Spring loaded locking latch affixes to it to the ladder
• Paint can hook included
• Mar-resistant rubber end caps

Reviews (4)

Quickclick
I have three extension ladders, and I don't put any of them up without the stabilizer on them. By being able to take it off, it make it easier to move the ladders. I can also use it on any of my ladders. It makes the ladder very stable. The stabilizer fits very well on the ladder.

Quickclick Stabilizer - can be dangerous
The quickclick stabilizer is not as handy as one would think. Yes, it is easy to take off and put on, but when you have a variety of extension ladder heights that you are adjusting your ladder to, it is easy to forget that the quickclick stabilizer limits the ability of the extension ladder to be placed at its shortest length. If you are not careful, when the extension ladder is placed at its quickclick impaired shortest length the quickclick stabilizer safety pin is what the ladder is supported on. If the pin should break (and it is a only a 1/8th inch diameter pin), the ladder will drop down to its true shortest length and the quickclick stabilizer will come off.

Buying my second one.
I already had one of these and since I'm now getting a whole ladder jack setup along with a second ladder, I definitely wanted one of these to go along with it. I'm sure they wouldn't recommend what I'm about to say for safety reasons, but I would point out that this item can make an aluminum extension ladder a lot more stable on slightly uneven ground. Because of the broad spread, the ladder will twist slightly to make up the difference and it's really solid!

This thing goes on or off in 5 seconds. No way would I ever get one of those bolt on kind. The cam action that holds it to the ladder looked a little iffy when I first saw it, but if you examine it you'll see that it's very well designed and I don't think you'll ever have a problem with it. I haven't.

Good Idea
This stabilizer is great because it goes on and off the ladder very easily and without tools. Definitley better than the cheaper stabilizers that attach with Ubolts that don't always fit right. ... Read more

Features

• 225 load limit per pair
• Padded calf brace
• Adjustable springs
• Leg height adjust
• Lightweight, easy to assemble

Features

• Comes with mounting hardware and instructions
• Attaches to Werner aluminum and fiberglass extensions
• Levels ladders on uneven surfaces automatically
• Adjusts up to 8-1/2"
• For type I and IA extension ladders

Reviews (7)

Installation of Werner PK80-2 auto-leveler
The instructions are detailed and didn't leave anything to the imagination. The instructions have different sections for the different ladders and require a careful study before and during the installation. At least the instructions are only in English, having multilingual instructions would make it way too confusing.

Installation took about 3 hours to accomplish for my D6020-2 20' fiberglass ladder and its a little scary permanently modifying such a nice ladder knowing that if you mess up the ladder can be permanently damaged or made useless. Take your time. Here is my list of things to be aware of going into this installation.

1) Be very careful aligning the drilling templates!!!

2) Center punch the hole positions good then your drill bit shouldn't wander. I didn't need to do this but you might pre-drill the holes with a smaller bit if necessary. You have 6 holes to drill over about 14" x 3" area so the drilling must be done very precisely if the side rail is to align correctly. The rail bracket doesn't have any give in it for error.

3) Double or triple check your measurements/instructions and drill bit sizes. Be very careful sawing off the square aluminum bar that runs through the rung as it has to be within 1/8" accuracy.

4) Don't remove the black electrical tape that comes on the side rails, this is done near the end of the installation.

5) Hack-sawing the side rail is the easy part. Previous review recommends a cutoff wheel which I'm sure works well but isn't necessary. Before doing this I'd mount the side rails to check your drilling accuracy. This is the point of no return before cutting off the existing ladder feet. If you messed up the drilling which I'm sure you won't if you are careful you can always abort the project here if necessary. The holes shouldn't hurt the ladder but cut off the feet and their side rails supports and, game over.

6) Drilling out the heavy rivets from the bottom rung is a royal pain and maybe a cutoff wheel would remove the head faster. I don't do that everyday so I'm sure there are better methods.

7) Have a good clutched drill and a 7/16" socket and it will speed up putting the 14 nuts on the side rails and the two feet.

8) Make sure you have good sharp drill bits, the sizes are indicated in a previous review and note they are less common drill bit sizes.

9) Wear a mask for the fiberglass drilling.

Good product, the ladder is definitely better and even stronger when the project is finished!

Great ladder accessory with a few caveats
As advertised, the PK80-2 Automatic Ladder Leveler easily adjusts to uneven ground. If you frequently use your stepladder in these conditions, this accessory is indispensible. This accessory does have the following disadvantages:

1. Installation should be done by an experienced handyman. Allocate a few hours to do the installation. Messing up the install may ruin the ladder, as the original ladder feet must be cut off.

2. The ladder will be somewhat heavier with the levelers installed. Before the levelers, I was able to easily move my 26-foot fiberglass extension ladder; with the levelers, I typically require help handling the ladder.

3. Installing the levelers widens the ladder foot spacing, as the levelers are placed outboard of the ladder rails. The resulting width is greater than the depth of two standard stair step depths, and the adjustment range of the leveler won't span two standard step heights; so, if your expecting to use the ladder against a wall with the feet on different steps of a stair, you'll likely have to still need some sort of platform/spacing under the lower foot.

The tools required for the install are: Power drill, 5/32", 3/16", and 9/32" drill bits, two 7/16" wrenches or sockets, #2 Phillips screwdriver, a hacksaw (I used an air-driven cuttoff tool), center punch, square, straight edge (2' or longer), scissors, pencil or marking pen, tape measure, metal file (sandpaper is also usable), adhesive tape, goggles, dust mask and gloves (for fiberglass ladders), and a 1-1/4" hole saw (for fiberglass ladders with rungs riveted to side rails).

Other tools listed in the instructions (for 2-section D1500 series ladder only, which I don't have) are 5/16" wrench or socket, 3/8" wrench or socket, 1/8" diameter punch, chisel, and C-clamp.

IMHO, the install is easier to do if you use air tools (i.e.: cut-off wheel, air drill, butterfly wrench). Also, the reattachment of the spacer sleeves is easier with rivets, instead of screws. I'd also suggest drilling pilot holes for the side rails as the 9/32" drill bit easily drifts off center when drilling through fiberglass; even after using a center punch.

Great Product...
I have a set of these on my 20 ft. ladder, and I am in the process of purchasing a set for my 32 footer.........I don't want to paint another day without them. They save time, work great, and most of all I don't worry that a block of wood will slip out from under the ladder leg . This is one product that can make your job much safer and easier if you use ladders a lot.

leveler
I have these on all three of my ladders, and wouldn't use a ladder without it. It makes it very easy to use the ladder on an uneven surface.

A MUST FOR ALL CONTRACTORS / LADDER OWNERS
I have a pair of the PK80 Level Master Automatic Ladder Levelers on my 28 foot ladder and I am purchasing a pair for my 40 foot ladder. This product really works !! It's just too hard to hold a 40 foot ladder up with one hand and adjust with the manual type levelers with the other hand. That's why the automatic type levelers are a must !!! They are well worth the money and easy to install. ... Read more

Features

• Can be used on either type I or IA ladders
• Accepts stages and planks to 20" width
• Lightweight, sturdy easy to use
• Designed for quick field adjustments
• Mounts on either side of extension ladder

Reviews (1)

definetly "on-top" ladder jacks
i've used long body ladder jacks before and there is not a product on the market that can compare. By far the Werner ladder jacks exceed all expectations from the general contractor to the week-end do-it-yourself handy man. For under $90.00 painting your house just became a whole lot easier. If you don't own a pair soon, somethings wrong! ... Read more

Features

• Adjustable load bar to accommodate varied width ladders
• Fits both full size and mini pickups
• Fits Dodge 1994 and newer, Chevy 1988 and newer, Ford 1992 and newer
• Removes and reinstalls easily for the occasional user
• 250-pound capacity

Features

• For use on a variety of surfaces
• Without having to be removed from ladder or adjusted
• Yellow safety coating and rubber bumpers

Reviews (2)

Corner Buddy Ladder Stabilizer
This tool is a great addition to your favorite extension ladder. I have used ladder stabilizer/ stand-offs for years primarily to facilitate painting windows or to avoid crushing aluminum gutters. This is a great enhancement to this line of ladder accessories. It is especially useful when you are screwing sections of downspout together or working on corner boards. It allows you to place yourself right on the corner so you have very good control.

The tool also works nicely on flat walls or even curved wall surfaces. If you work around corners frequently, this is a great little accessory.

Corner Buddy Works!
This stabilizer works great in corners that I could not reach before. It is also a good stabilizer. Hooked over the gutter onto the shingles it provides a much safer work platform then leaning a ladder on the gutter itself. ... Read more

Features

• Sold as a pair
• Extra strength steel design
• Adjusts to fit between top two ladder rungs
• For use with wood, fiberglass, or aluminum
• For use with round or d-rung styles

Reviews (2)

It works
This product does its job, but there isn't anything on Amazon to indicate how it works - and the picture isn't very helpful on its own. The thing is, you get two of the pictured hangers (for the indicated price). The small hook goes under the second rung from the top of your ladder. The little wheel is part of a clamp that goes over the top rung of the letter and clamps down to hold the apparatus firmly to the ladder. If you have a ladder you use for climbing on roofs, you can just leave the two brackets attached. To use it, you turn the ladder so that the wheels are down and roll it up the roof. This can be done from a stepladder or another ladder leaning agaist the wall. When the large hook is above the peak of the roof, flip the ladder over and it hangs down the roof. Great for metal roofs that are too slick to walk on.

great tool, but be careful!
As a residential contractor, I've used this tool many times in places where it was impossible to set up a ladder from below. This tool lets you hang the ladder from the roof ridge. However, I wish to emphasize common sense and caution when using it...1.Make sure you firmly tighten this tool to your ladder...your life depends on it, 2.Do not let the ladder lay on any surface that isn't reasonably flat, for instance, don't rest the ladder on top of nailed down 2x4 roof cleats, what happens is that the roof cleats can act as fulcrums and if your weight on the ladder goes below the fulcrum(2x4), then the upper part of the ladder will lever its ridge hooks off of the ridge and down you go...I learned this one the really hard way. I know it's really just using common sense, but sometimes you just forget... 3. The use of a fall arrest harness as a backup system isn't a bad idea. I think I'd like the ridge hooks to be longer and somehow padded to protect the roof shingles. Still, when I can't use the ladder from the ground, this is the tool I reach for. ... Read more

Features

• Can be used on either type I or IA ladders
• Accepts stages up to 14" width
• Lightweight, sturdy easy to use
• Designed for quick field adjustments
• Mounts on inner and outer front ladder

Reviews (1)

Werner Aluminum ladder jacks
They are light weight. Easy to install and handle . Safer to handle than older style steel ladder jacks. Feel very stable when in use. I am very satisfied with this product. ... Read more

Product Description

Ladder-Max MAXIMIZES your ladder's capabilities! The Ladder-Max unit is specifically designed to add a great amount of safety for extension ladder users, whether the ladder is placed on a side wall (vertical surface) or the roof of a structure. This is accomplished with the two "full steps" being bolted on two arms carefully bent to a 90° angle to create an arch form. When the Ladder-Max unit is placed for use, its arms are positioned to create a wedge. With just a small amount of weight placed on the ladder the wedge creates pressure at the tip of the arm and causes the tip to adhere to the surface. This minimizes lateral and horizontal slip. By attaching the Ladder-Max unit to an extension ladder, the user immediately increases the utility and safety of the ladder. The unit can be placed directly on the roof for safe entrance and exit to and from the roof. Ladder-Max will keep the extension ladder off the leading edge of the roof and rain gutters. The user will assume a more natural work angle and be able to lean into the ladder and the work to accomplish the task. The user can stand safely and work because of the wider stance and additional stability provided by the Ladder-Max unit. No other ladder stabilizer comes close to the advantages offered by Ladder-Max's steel construction, strong stable wedge design, 19 inches of standoff and OSHA certified roof placement feature. Ladder-Max will fit all extension ladders manufactured after 1972 such as Werner, Gorilla, Louisville, Howard, Krause, Cuprum, Lynn, Green Bull, Keller, Columbia, Watling, Berg, Michigan, Oaks, Inland, Pat Johnson, American, Holland, Metallic, All Right and Bauer. Ladder-Max attaches in seconds without tools. The Ladder-Max is proudly made in the USA. ... Read more

Features

• Fits extension and articulated ladders - aluminum, fiberglass and wood
• User friendly - attaches to ladder in 10 seconds or less without tools
• 19 inches of standoff - roof placement feature keeps ladder from denting gutters and eaves
• Durable steel construction means it will last for years under homeowner and professional use.
• Not spongy or twisty like aluminum standoffs - Meets OSHA Type IAA-375 lb duty standard

Product Description

Sold in pairs. Adjusts to fit between two rungs of most ladders. Makes it possible to place ladder on roof without damage to shingles. Always use two Ladder Hooks per ladder. Made of steel for strength. Safety Orange finish. ... Read more

Features

• Sold as a pair.
• Makes it possible to place ladder on roof without damage to shingles.
• Adjusts to fit between two rungs of most ladders. Can be used with round or d-rung ladders.
• Always use two Ladder Hooks per ladder.
• Made of steel for strength. Safety Orange finish.

Features

• Snaps over extension ladder end rail caps
• 2 per package
• Fits on all single or extension ladder except wood
• Prevents damage to support surfaces
• Resists paint, stains, thinner and solvents

Reviews (1)

Easy to install, protects surfaces from ladder end damage.
I installed a pair of these on my 40' Werner fiberglass extension ladder. They work wonderful, protect the exterior wall which I was painting last fall while I moved the ladder up and down. Installation was simple - just slip these covers over the ladder ends.

On the longer ladders such as mine, which is also substantially heavier at 90 pounds than shorter versions, the ladder can be a bit unwieldy to extend or contract, or otherwise manipulate. This risks damaging the wall you're painting, unless you protect the surface from the ladder ends with homemade remedies or covers like these. ... Read more

Product Description

The Dura-3 is the one of the finest stilts available. Great innovative design concepts and technology. Features: Steel inserts at the adjustment screw location and field replaceable nylon leg sleeves. Heavy duty screw on replaceable soles are mounted on "super tough" nylon floor plates. Replaceable nylon bearings at leg connections and lock nuts on hinge bolts give extra wear and longer stilt life. Snap-in nylon sleeves separate the telescoping legs and steel inserts prevent adjustment hole wear. Ankle movement is made possible with a direct spring activation method which also provides individual spring adjustment for forward and rearward motion ... Read more

Features

• Professional grade tool
• Accomplish more with less effort
• Leg support strut fastens to stilt above adjustment separation point
• Exceptional for the drywall trade or whenever extra height is needed
• No need to adjust side leg supports when adjusting stilt height

Product Description

When the Little Giant Ladder has to be used in a lean-to position on an uneven surface, the Leg Leveler offers a safe, stable solution. The Leg Leveler is made to meet the same extra heavy-duty standards as our ladders and attaches easily. ... Read more

Features

• FREE SHIPPING
• Weight: 5 lbs
• 1 - Year Warranty

Product Description

The Dura-3 is the one of the finest stilts available. Great innovative design concepts and technology. Features: Steel inserts at the adjustment screw location and field replaceable nylon leg sleeves. Heavy duty screw on replaceable soles are mounted on "super tough" nylon floor plates. Replaceable nylon bearings at leg connections and lock nuts on hinge bolts give extra wear and longer stilt life. Snap-in nylon sleeves separate the telescoping legs and steel inserts prevent adjustment hole wear. Ankle movement is made possible with a direct spring activation method which also provides individual spring adjustment for forward and rearward motion ... Read more

Features

• Professional grade tool
• Accomplish more with less effort
• Leg support strut fastens to stilt above adjustment separation point
• Exceptional for the drywall trade or whenever extra height is needed
• No need to adjust side leg supports when adjusting stilt height

Features

• Stand Off / Support Bar
• For use with all ClimbTek ladders: CT 212, CT 412 & CT 416
• May be used as an additional support bar or as a stand off bar
• Comes with easy to use hardware for quick installation

Product Description

The Dura-3 is the one of the finest stilts available. Great innovative design concepts and technology. Features: Steel inserts at the adjustment screw location and field replaceable nylon leg sleeves. Heavy duty screw on replaceable soles are mounted on "super tough" nylon floor plates. Replaceable nylon bearings at leg connections and lock nuts on hinge bolts give extra wear and longer stilt life. Snap-in nylon sleeves separate the telescoping legs and steel inserts prevent adjustment hole wear. Ankle movement is made possible with a direct spring activation method which also provides individual spring adjustment for forward and rearward motion ... Read more

Features

• Professional grade tool
• Accomplish more with less effort
• Leg support strut fastens to stilt above adjustment separation point
• Exceptional for the drywall trade or whenever extra height is needed
• No need to adjust side leg supports when adjusting stilt height

Features

• Up to 8 feet spacing between brackets
• Adjustable to fit 10-degree pitch, 10-inch platform
• All steel construction
• Easy installation
• 1 man per 8 feet of staging plus 40 pounds

Reviews (1)

Adjustable Roof Jacks
Most of the houses that we build have a 12-12 roof. I can't tell you how nice it is to stand on a 2x10 plank.I would be lost without my adj.roof jacks, they take up less room when they are being stored, I have some of the fixed jacks they are in my shop collecting dust. A fine product you can't go wrong. ... Read more

Features

• Non-marring rubber tips
• Works with aluminum, wood, or fiberglass ladders
• All necessary hardware included
• Attaches in minutes without tools
• Made of light weight aluminum 48-inch span 12-inch depth

Reviews (2)

Ladder Stabilizer
I have a Werner 28 foot 1A Fiberglass Ladder, I use it on a two story town house here in Maine. I have never had a problem ,with this product. It never has ever twisted on me.It has always given me afilling of bening stable. I give it 4 stars only,because I've not tried any other product in this catergory, (don't see no need too).

Crawford LS4XXX Ladder Stabilizer
I have two extension ladders, and I attached this stabilizer without a problem to my first ladder. However, the second ladder has thicker steps and rails which made installation very difficult -- I had to bend a few of the U bolts. Once installed, the stabilizer pretty much works as expected. ... Read more

Features

• Made of heavy duty canvas

Reviews (1)

Cheaper from Manuf directly?
Hello,

I bought the 12' ladder from Amazon and this Carry Bag. The ladder came with a "special 30-day offer" for a Telecarry Bag for $.... I would guess the Telecarry bag is the same as this product. The ad says "Regularly $.... plus s&h;. I am not sure if the $...shipping or not. I'm expecting my carry bag to arrive from Amazon soon. ... Read more

Amazon.com Product Description

Secure your extension ladders quickly and easily with Gripster ladder stops. Attached to the top of a ladder's side supports, these ladder stops greatly minimize the slipping and skidding that often occur when a ladder is placed against a flat surface. Featuring round safety cups that expand when a user begins to climb, the stops grip the flat surface to keep the top of an extension ladder secure. The ladder stops also protect work surfaces from the dents, scuffs, and scratches often caused by ladders. ... Read more

Features

• Round safety cups expand for added stability and grip-ability
• Attach to the top of a ladder's side supports
• Secures extension ladders by minimizing slipping
• Protects surfaces from ladder marring
• Prevents dents, scuffs, and scratches