Features

• Wide head, sharklike serrated-tooth design
• Accessory item for 401 and 501 Porta-Nailer
• 10,000-pack

Reviews (2)

Buy the floor nailer that uses these nails
Its that simple. Spend the bucks, and you will not regret it. These nailing cleats are the best way to attach a piece of flooring to a subfloor. They hold tightly forever. I've never had a callback on a floor put in with porta-nails cleats. I own the new pneumatic porta nailer and think its great. Its a little more money than the competition, but well worth it. No jambs or messed up nails. It just works.

Porta-Nailer
The Porta-Nailer is by far the most reliable flooring nailer on the market. The nails hold extremely well. They do not split the wood. Because the nailer is actuated by the hammer that is included, the boards are driven up quite tight. It will straighten even the most stubborn flooring. I have owned this nailer for ten years and have had no trouble. ... Read more

Features

• 2-inch finish brad nails
• 18 gauge
• 5,000 per pack

Reviews (3)

Smooth as Silk!
Just finished the casing on the closet door frames in my daughters' room. These were flawless in my Accuset 200BN.
Never a jam with the 2" brads or the 1 1/4" brads!

Average Performance Brads
These are functional, but not very tough. They seem to be a little softer than some other brads I have used, which lets them deflect fairly easily at this long length. Therefore, keep your fingers out of range! They do hold well and are difficult to remove if you make a boo-boo.

Nailed again
I am a finish contractor and I really find it nice when i can buy a quality product that will not damage either my tools or the project that I am working on. These nails feed thru my accuset brad nailer w/o any trouble at all and plan to switch over to them fulltime. ... Read more

Features

• Waterproof Storage case
• Durable Polyurethane Hot Melt Applicator System
• Cordless Applicator
• Durable Trigger components for refined adhesive control
• Heating Cylinder houses cartridges for extended use

Reviews (8)

Bought 2 and both failed
The concept of the tool and the strength of the glue are good, but I the glue delivery is flawed. Despite following the instructions on capping the nozzle before it cooled, it filled and hardened on two separate attempts. Yes, I bought a second one, figuring I had done something wrong. In the second version the glue never stopped flowing until it fully engulfed the nozzle and hardened.

I found this product expensive and unacceptable.

What they don't tell you
I wish I had seen the reviews on Amazon before I bought the kit.

When I finally read the (very) small print on the glue cartridge itself, I was very annoyed. It tells you that once opened you should use all of the glue within four weeks. You have to open the package to read this fact. There is no mention of it on any marketing blurb, the instructions or even the cartridge's external packaging. It seems the glue is sensitive to moisture and will set in the cartridge if you don't use it pronto. If I had known this, it would have stopped the purchase dead.

The Titebond website does explain (if you track it down in the FAQ's) that there are techniques you should use to ensure it does last AS LONG AS FOUR WEEKS. Great, that means if you don't know about this, it won't even last that long.

I now realize that this is a very special-purpose tool. It might work fine for BIG jobs where you need to make lots of fast setting and strong joints. But when will that job come along? I bet if I pull it out in about twenty years when I have such a job to do, I won't be able to find the glue on the market.

just plain bad!
GREAT GLUE...but you need to find, not a better way, but ANY other way to get it out hot. First tube pressurized and blew out the back, second tube (after hhours of cleaning the tube slot) wouldnt come out the tip smoothly at all. i was'nt going for three strikes...this stuff is too hot to mess arround with. wait for a better model using the same glue to arive.

the good, the bad, and the broken
I have had the glue kit for 2 years. THE GOOD. It has worked great for several custom counter top applications and small, quick repair jobs. THE BAD. The problem I had was after the glue had been heated and used several times, along with being about a month old, it would not liquify and come out of gun. Half of a tube of glue is garbage. THE BROKEN. After putting an unused tube in the gun, and heating it for 30 minutes, I tried dispensing glue. For some reason the glue didn't soften enough and an ear broke off where the gun locks together. Gun is now usless.

Big disappointment
The glue is fine, and if it worked I would be very happy. Unfortunately I have been unable to control the flow. On some tubes the glue pours out, which is messy and expensive. And other tubes it is so slow to get the glue out, that by the time you get enough out, it is already setting up. Very aggravating. ... Read more

Features

• Unaffected by finishes
• Waterproof-Superior Strength
• Lower Application Temperature
• Longer Open Assembly Time
• Resists Solvents, heat & mildew

Features

• 1 1/4" long
• 7200 per box
• galvanized
• Weight = 35 pounds

Features

• Pin designed for delicate projects such as craft assembly
• Package includes 2,670 1" pins
• 23 gauge galvanized pin
• Convenient clam shell package

Features

• 3-1/2" x .131 plain shank framing nails full round head
• Quantity 500/box
• Fits the following guns Hitachi NR83A, NR90AC, Duofast CN350, Senco SN60, SN65, Makita AN8300, Porter Cable FR350

Reviews (4)

Good nails. Good price.
If you have a Porter Cable FR350, for some reason finding nails can be a slight problem. The mega home store with the orange sign has them, but not consistently. So these are a good stop-gap until you can find more.

They drive well and seem to hold well.

Won't work with the PC FR530 Nail Gun
These may be great nails, but they'll probably jam and misfire with the Porter Cable FR530 nail gun. The FR530 needs plastic-collated nails, not paper-collated like these are. I made the mistake of buying a ... case of paper-collated nails, only to have non-stop problems with them. Only on the Porter Cable website does it mention that the gun uses plastic-collated.

a bit short
good nails, good collating, but they are not 3-1/2 inches long, only 3-1/4......

Some Excellent Nails!
If you are looking for the highest quality nails for your nails gun then you better get these. I have used these forever and they have performed to the highest extent the whole time. They have never jammed or messed up my guns. These are top of the line ... Read more

Features

• 1-inch finish brad nails
• 18 gauge
• 5,000 per pack

Reviews (2)

Shiny, Sharp and Cheap
Wow! Age of wonders this is a fantastic product.

Itty, Bitty Brads for Your Power Nailer
These are fairly soft as brads go, but at this length, deflection is not a major problem. You do still have to be careful, though. These are fine for smaller chores, like fastening thin shelves in dadoes or applying trim moldings. They hold well, but are tough to remove if you misfire. ... Read more

Features

• 2-inch galvanized finish nails
• 15 gauge
• 4,000 per pack

Features

• 1,000/box
• L-shaped flooring cleats
• Nails 200 square feet of flooring per box

Reviews (1)

need more nails
If you are installing 2 1/4" hardwood flooring, one box(1000 nails) is needed per 100 SF - nailing every 6-8" ... Read more

Features

• 1-1/2-inch finish brad nails
• 18 gauge
• 5,000 per pack
• For use with Hitachi, Senco, Porter Cable, Airy, Bostitch and Accuset nail guns

Reviews (3)

Work well for me.....
I have used these nails extensively in my Bostich BT-50 (on my 3rd box of 5000) with no problem at all. Possibly other manufacturers have lower tolerances or are not up to par with the Bostich, but the nails work just great.....

Useful Size, But a Little Too Flexible
This is about the most common brad size I use in my shop. These are fairly soft, so deflection can be a problem if you are not careful about the material you are nailing. Avoid knots and obtuse angles on plywood. They hold well and can be difficult to remove once driven.

Poor Quality Nails for the Porter-Cable Finish Nailer
These nails are not of the quality necessary for the Porter-Cable Finish Nailer that they are typically advertised with (FN250A). They sometimes came out 2 at a time, not at all, or caused the nailer to jam. I called Porter-Cable, and acquired their nails, and the problems went away. I would not recommend these nails, especially for this nailer. ... Read more

Features

• Wet well keeps glue ready
• Roller head for flat surfaces
• Flat nozzle for biscuit joinery
• Pinpoint head for precision placements
• Round head for dowels and dovetails

Reviews (7)

The Art of Glueing
I never really looked at a glueing project as being an art, but this glue set allows you to be a true artist. Just as a painter has to have the right paint brush for a project, this glue set gives you the right glue attachment for the project. And it has made all the difference in the outcome of that project. The right amount of glue is placed exactly where you want it, no drips, very little excess, no spill overs onto the main surface of the board.

Each attachment, easily kept available and stored when you can find it, works with each specific project. Whether it is a dovetail, dado, bisquit spline, pinpoint or just joining two boards together, this set gets the job done.

The wet well works just fine, keeping the glue "wet" and the bottle inverted for easy glue extraction, especially when the bottle is getting low.

I didn't think I really needed this glue set, that there is not an art to glueing, that all those attachments were just extra "fluff". I have learned my lesson, I REALLY enjoy being a glue artist, using the right tool and getting the project completed with NO glue overflow!!

Works great but
clean up is the only problem I've had with this product. This glue kit was well thought out. With a vast array of attachments, I can't imagine any glue up situation a woodworker couldn't conquer. But beware, if you get pulled away from a project or forget to clean out the attachments be prepared to to spend some quality time with a paper clip. If your shop doesn't have running water, like mine, it can be a real challenge. Best of luck.

This is a nice kit, great for the money
I just used this kit for the first time. I was gluing some melamine sheets with Roo Glue (specially made for melamine) The set up time was 15 minutes, so I had a lot of surface area to cover in short order. This glue kit, using the glue roller did a nice job. It enabled me to cover a lot of surface area quickly. The amount of glue that is released is based on how much you squeeze the container. You can easily see the flow, so guesstimating is pretty easy.
My only dilemma is when doing biscuits and glue edge joinery; it is necessary to switch heads. When you are dealing with glue that is sure to get messy. So my quest is to find a dedicated biscuit joining glue bottle. That way I can use both at the same time without making head changes.
I think this kit is a great idea. It might be all plastic, but is ideally suited for the purpose. Highly recommended.

Great, but not perfect
This has proved to be a useful tool, but I find it a little lacking when gluing up biscuits, which is why I bought it. I still find myself using the glue straight from the bottle at times, which attests to its usefulness.

...it works great, what more could you ask for
This is simple and straight forward. The roller works very well...I will tell you not to let the glue dry on the roller, while it may not stick to the roller it is not easy to get off once it does dry. When you are done take a couple of minutes and rinse off the roller in the sink.

The rest of the attachments are a cool idea but the hassle of changing them out makes them less friendly to use than the standard nozzle on a regular carpenter's glue bottle. I love the roller and use it all the time and that makes this item worth having but I wouldn't get excited about the other attachments if I were you. ... Read more

Features

• 1-1/4-inch finish brad nails
• 18 gauge
• 5,000 per pack

Features

• Pin designed for delicate projects such as craft assembly
• Package includes 2,492 assorted 1/2", 5/8", 3/4" and 1" pins
• 23 gauge galvanized pin
• Convenient clam shell package

Features

• 2-1/2-inch finish nails
• 16 gauge
• 2,500 per pack

Reviews (1)

Poor Quality Nails for the Porter-Cable Finish Nailer
These nails are not of the quality necessary for the Porter-Cable Finish Nailer that they are typically advertised with (FN250A). They sometimes came out 2 at a time, not at all, or caused the nailer to jam. I called Porter-Cable, and acquired their nails, and the problems went away. I would not recommend these nails, especially for this nailer. ... Read more

Features

• 2-inch finish nails
• 16 gauge
• 2,500 per pack

Reviews (1)

Really Hit The Nail On The Head.....
Great product works great in Bostich nailer. Will purchase again when needed. ... Read more

Features

• 1-1/2-inch finish nails
• 16 gauge
• 2,500 per pack

Features

• 5,000 nails per box
• 2-3/8-inch x .113 plain shank framing nails with full round head
• Fits Hitachi NR83A, NR90AC, Duofast CN350
• Senco SN60, SN65, Makita AN8300
• Porter Cable FR350

Features

• 20-degree 16-gauge nail for finish nailing
• Manufactured out of cold worked carbon steel
• Galvanized in a "hot-dip" process which ensures that the fastener will resist rust and moisture

Features

• Pin designed for delicate projects such as craft assembly
• Package includes 2,670 1/2" pins
• 23 gauge galvanized pin
• Convenient clam shell package