Features

• Unaffected by finishes
• Waterproof-Superior Strength
• Lower Application Temperature
• Longer Open Assembly Time
• Resists Solvents, heat & mildew

Features

• 1 1/4" long
• 7200 per box
• galvanized
• Weight = 35 pounds

Features

• Pin designed for delicate projects such as craft assembly
• Package includes 2,670 1" pins
• 23 gauge galvanized pin
• Convenient clam shell package

Features

• 3-1/2" x .131 plain shank framing nails full round head
• Quantity 500/box
• Fits the following guns Hitachi NR83A, NR90AC, Duofast CN350, Senco SN60, SN65, Makita AN8300, Porter Cable FR350

Reviews (4)

Good nails. Good price.
If you have a Porter Cable FR350, for some reason finding nails can be a slight problem. The mega home store with the orange sign has them, but not consistently. So these are a good stop-gap until you can find more.

They drive well and seem to hold well.

Won't work with the PC FR530 Nail Gun
These may be great nails, but they'll probably jam and misfire with the Porter Cable FR530 nail gun. The FR530 needs plastic-collated nails, not paper-collated like these are. I made the mistake of buying a ... case of paper-collated nails, only to have non-stop problems with them. Only on the Porter Cable website does it mention that the gun uses plastic-collated.

a bit short
good nails, good collating, but they are not 3-1/2 inches long, only 3-1/4......

Some Excellent Nails!
If you are looking for the highest quality nails for your nails gun then you better get these. I have used these forever and they have performed to the highest extent the whole time. They have never jammed or messed up my guns. These are top of the line ... Read more

Product Description

Compatible with ALL Security+ systems, including Chamberlain, Sears, Craftsman and Raynor code rolling residential openers (Safety Signal). Compatible with Liftmaster remotes models 91LM, 96LM, 970LM, 971LM, 972LM, 973LM, 974LM. Compatible with Chamberlain remotes models 950CB, 953CB, 956CB. Compatible with Sears remotes models 139.53681 and 139.53680. This unit is the same as the Chamberlain model 940CB, Sears model 139.53684 and the Liftmaster 67LM (old model number). Compatible with garage door opener operator model numbers 1240R, 1245R, 1246R, 1255R, 1256R, 1265, 1280R, 1000SDR, 2000SDR, 1245 GMR, 1255GMR. Compatible with Security+ garage opener receiver model numbers 335LM, 535LM, 412HM, 635LM. Compatible with models manufactured from 1997-present WITH an orange or red "learn" button. This Keyless Entry also features a temporary password option to let you give friends, relatives or maintenance people limited access. ... Read more

Features

• Lift-Master Wireless Keyless Entry System with Security+ Anti-Burglary Coding
• Compatible with ALL Security+ systems
• Lets you open your garage door without remote control or keys
• Code changes every time you use this unit (defeats code grabbers)
• Over 100-billion codes for maximum security

Features

• 1-inch finish brad nails
• 18 gauge
• 5,000 per pack

Reviews (2)

Shiny, Sharp and Cheap
Wow! Age of wonders this is a fantastic product.

Itty, Bitty Brads for Your Power Nailer
These are fairly soft as brads go, but at this length, deflection is not a major problem. You do still have to be careful, though. These are fine for smaller chores, like fastening thin shelves in dadoes or applying trim moldings. They hold well, but are tough to remove if you misfire. ... Read more

Features

• 2-inch galvanized finish nails
• 15 gauge
• 4,000 per pack

Features

• 1,000/box
• L-shaped flooring cleats
• Nails 200 square feet of flooring per box

Reviews (1)

need more nails
If you are installing 2 1/4" hardwood flooring, one box(1000 nails) is needed per 100 SF - nailing every 6-8" ... Read more

Features

• 1-1/2-inch finish brad nails
• 18 gauge
• 5,000 per pack
• For use with Hitachi, Senco, Porter Cable, Airy, Bostitch and Accuset nail guns

Reviews (3)

Work well for me.....
I have used these nails extensively in my Bostich BT-50 (on my 3rd box of 5000) with no problem at all. Possibly other manufacturers have lower tolerances or are not up to par with the Bostich, but the nails work just great.....

Useful Size, But a Little Too Flexible
This is about the most common brad size I use in my shop. These are fairly soft, so deflection can be a problem if you are not careful about the material you are nailing. Avoid knots and obtuse angles on plywood. They hold well and can be difficult to remove once driven.

Poor Quality Nails for the Porter-Cable Finish Nailer
These nails are not of the quality necessary for the Porter-Cable Finish Nailer that they are typically advertised with (FN250A). They sometimes came out 2 at a time, not at all, or caused the nailer to jam. I called Porter-Cable, and acquired their nails, and the problems went away. I would not recommend these nails, especially for this nailer. ... Read more

Features

• Wet well keeps glue ready
• Roller head for flat surfaces
• Flat nozzle for biscuit joinery
• Pinpoint head for precision placements
• Round head for dowels and dovetails

Reviews (7)

The Art of Glueing
I never really looked at a glueing project as being an art, but this glue set allows you to be a true artist. Just as a painter has to have the right paint brush for a project, this glue set gives you the right glue attachment for the project. And it has made all the difference in the outcome of that project. The right amount of glue is placed exactly where you want it, no drips, very little excess, no spill overs onto the main surface of the board.

Each attachment, easily kept available and stored when you can find it, works with each specific project. Whether it is a dovetail, dado, bisquit spline, pinpoint or just joining two boards together, this set gets the job done.

The wet well works just fine, keeping the glue "wet" and the bottle inverted for easy glue extraction, especially when the bottle is getting low.

I didn't think I really needed this glue set, that there is not an art to glueing, that all those attachments were just extra "fluff". I have learned my lesson, I REALLY enjoy being a glue artist, using the right tool and getting the project completed with NO glue overflow!!

Works great but
clean up is the only problem I've had with this product. This glue kit was well thought out. With a vast array of attachments, I can't imagine any glue up situation a woodworker couldn't conquer. But beware, if you get pulled away from a project or forget to clean out the attachments be prepared to to spend some quality time with a paper clip. If your shop doesn't have running water, like mine, it can be a real challenge. Best of luck.

This is a nice kit, great for the money
I just used this kit for the first time. I was gluing some melamine sheets with Roo Glue (specially made for melamine) The set up time was 15 minutes, so I had a lot of surface area to cover in short order. This glue kit, using the glue roller did a nice job. It enabled me to cover a lot of surface area quickly. The amount of glue that is released is based on how much you squeeze the container. You can easily see the flow, so guesstimating is pretty easy.
My only dilemma is when doing biscuits and glue edge joinery; it is necessary to switch heads. When you are dealing with glue that is sure to get messy. So my quest is to find a dedicated biscuit joining glue bottle. That way I can use both at the same time without making head changes.
I think this kit is a great idea. It might be all plastic, but is ideally suited for the purpose. Highly recommended.

Great, but not perfect
This has proved to be a useful tool, but I find it a little lacking when gluing up biscuits, which is why I bought it. I still find myself using the glue straight from the bottle at times, which attests to its usefulness.

...it works great, what more could you ask for
This is simple and straight forward. The roller works very well...I will tell you not to let the glue dry on the roller, while it may not stick to the roller it is not easy to get off once it does dry. When you are done take a couple of minutes and rinse off the roller in the sink.

The rest of the attachments are a cool idea but the hassle of changing them out makes them less friendly to use than the standard nozzle on a regular carpenter's glue bottle. I love the roller and use it all the time and that makes this item worth having but I wouldn't get excited about the other attachments if I were you. ... Read more

Features

• Hardwood to hardwood
• 1000 pack

Reviews (5)

They do it well
I bought these with the Kreg Pro Pack Pocket Hole Kit. They do the job well. Other sizes are available as well. It is a good idea to stock up on this 1 1/4" size, since they are intended for use in the most popular wood size of 3/4". That way you get 1/2" bite into the joining wood. These fine threaded screws are made for hardwoods. The point is so sharp that they will go into Red Oak without having to drill a pilot hole. Even though the Kreg jig comes with a drill bit with a tip on it, that bit does not even penetrate the first piece of wood, let alone the joining piece. They depend on the sharpness of these pocket hole screws to make their way through even the hardwoods. The shaft is narrow enough so as to not cause a split.
A coarse thread is available for soft woods as well.
These Kreg screws are well made, and do the job well. Hope this helps.

Kreg SPS-F125 1-1/4" #6 Hardwood Screws
I have just built an entire set of kitchen cabinets using hickory, which is very hard in case you haven't worked with it before. I did not have one twist-off or spin-out with these screws. Excellent screws.

Note differences between washer and pan head
I bought the Kreg pocket hole kit and love it. It comes with a few dozen 1 1/4 screws, and I bought these thinking they are the same. These are the Pan Head, which are nice, but the ones in the kit are washer heads that have more purchase on the bottom of the pocket. The pan heads will sink into the wood, even using walnut and cherry. I have not had one fail yet, but I worry that they sink about 3/16" deeper into the joint than the other screws. Visit the Kreg site to find the whole assortment of screws and plugs.

screwy for screws
What makes true happiness? Love, a good job, lots of money? Well I think it is none of those. I believe true happiness comes from screws and how well they go into the woood. It was a beautiful day, the sun beat down, I had the radio on, I was driving around. Trees went by, me and dale were singing "little run away" I was a flying. I got the Kreg SPS-F125 1-1/4" #6 Fine screw in a 1000 pack equiped with duel tighten control force feedback, notch haver plug and of course the rifts that make it tighten on a dime. I was running down a dream that never would come to me, working on a mystery going where ever it leads, RUNNING DOWN A DREAM. I used my brand new "built ford tough" type screw driver and the screws just cut right through that wood it had to be one of the best days of my life. I'm a big man but i'm not afraid to admit i cried there, cried like a little baby.

Fabulous Fine No. 6
These screws just ooze into wood like a hot knife through butter. Since using these screws to repair a drawer and refasten a picture frame, I've had a few compliments for my fine taste in screws. First I drilled tiny holes to accommodate the insertion.

My original thought was that I would have to drill two sizes larger that the tiny initial hole I drilled. Not to be, for these fine #6's slid right in there with that finely honed point that was lovingly crafted at its beginning.

Of course I can't go in to detail as to the overall longevity of the beautiful finish. These screws that I've used have only been in place for weeks.

After two or three years though, I'll be sure to give an update on the resiliency of the finish. ... Read more

Amazon.com Product Description

Turn two-by-fours into any shelving you need using only a saw and screwdriver. Using ShelfLinks, you can connect inexpensive two-by-fours in any shelving configuration you need with just a few square saw cuts and a screwdriver. Build a great-looking entertainment center on the cheap. Quickly put up shelving in your garage and organize your tools and clutter once and for all. Anywhere you need a custom shelving solution, ShelfLinks make it happen quicker and less expensively than using flimsy, one-size-only plastic or metal shelving. Using a building-block mentality, ShelfLinks are easy to put together and can be modified or added to as storage or work areas change. Worried about strength? ShelfLinks support spans up to 8 feet, and each shelf can hold up to 1,000 pounds. ... Read more

Features

• Easy to build shelves require only straight cuts
• Rugged, heavy duty- holds 1000 lbs per shelf
• Make any size to fit anywhere you need them
• Lifetime warranty

Reviews (3)

Brackets don't fit 2x4's snugly
I was disappointed to see a 1/4" gap between the 2x4 and the bracket on the longer dimension. (My 2x4's are 1-1/2"x3-1/2", but the opening is 3-3/4" wide.)

Need more than a saw and a screwdriver
This is a great product. You can build these shelves with just a saw and a screwdriver, BUT you better have a lot of strength in that screw driving arm, a great eye for right angles, and a lot of time if you plan to cut all of those two-by-fours with a hand saw. I suggest that optimal tools for the job are: tape measure, angle, level, circular saw, and power drill with a phillips head or a power screwdriver.

Instead of buying off the shelf units that may or may not fit the space intended, and which cost substantially more, you can build customized shelves that fit the space perfectly. If you live in an urban area where storage space is tight and getting the most out of every square foot is important, then this product can be useful. I buy the cheapest two-by-fours available and use the shelves for storage in my basement. Note: the shelves are 16" deep.

GREAT PRODUCT
Everything to make "shelf building" simple. It's flexable and easy to configure to just about any dimensions you might need. If you can saw a straight line and know how to use a screwdriver you are in business. ... Read more

Features

• Double-wall blow molded enclosures
• Large storage capacity -- 15.2 cu ft
• Weight capacity -- 510 lbs (35+ paint cans)
• Lockable doors
• Easy to assemble -- no tools or hardware required

Features

• Specially designed for pocket hole joinery
• Small tip provides a clearance hole for the screw shank
• Large diameter produces flat-bottomed hole for the head of the screw
• Corded, high rpm drill is recommended

Reviews (2)

It's good to have a backup
I purchased the Kreg Pro Pack unit, that comes with this bit. My feeling is that since it is the only one, if for any reason I am in the middle of a project and the tip breaks, or I have any other problem with it, I don't want to be left standing while I wait for another one. So I bought it as a backup.
This bit does a great job, and the Kreg pocket hole systems won top of class award in every category in a recent run off by one of the top woodworking magazines. They won in every size, and every model from the mini on through to the professional bench top.
I don't really anticipate having a problem with the drill bit, but when doing this for a living, you need a parachute, in the event the unusual happens. This bit is built strong, and is rather large, so breakage is not likely, but the tip that protrudes on the end is a lot smaller, and that could possibly break. Additionally, if you are pocket holing all day, the bit could dull, and that would requires a replacement.
Overall highly recommended.

High Quality!
It is 3/8" in diameter and works very well with Kreg's or similiar make self-boaring screws. You can use with any drill driver. Simple! ... Read more

Features

• 1-1/4-inch finish brad nails
• 18 gauge
• 5,000 per pack

Features

• Pin designed for delicate projects such as craft assembly
• Package includes 2,492 assorted 1/2", 5/8", 3/4" and 1" pins
• 23 gauge galvanized pin
• Convenient clam shell package

Features

• Washer head seats flush in the bottom of the pocket to eliminate pull through for a finer outcome
• 1-1/4-inch screw length for joining 3/4-inch hardwood material such as oak, maple, hickory, cherry and walnut
• Maxi-Loc washer head for precision driving and the elimination of overdriving in softer stock
• Self-tapping auger tip eliminates the need for pre-drilling for less downtime and more productivity
• Large diameter steel shanks for optimal durability

Reviews (1)

5 stars for a garage door accessory, maybe i'm pushing it
A simple product that does exactly what it is suppose to do.Easy to install. Just make sure to check the placement once the glue is down and the door is closed. This will ensure if the threshold moves you still have time to fix.
No more rain water in the garage after 3 big storms. gotta love it ... Read more

Features

• 2-1/2-inch finish nails
• 16 gauge
• 2,500 per pack

Reviews (1)

Poor Quality Nails for the Porter-Cable Finish Nailer
These nails are not of the quality necessary for the Porter-Cable Finish Nailer that they are typically advertised with (FN250A). They sometimes came out 2 at a time, not at all, or caused the nailer to jam. I called Porter-Cable, and acquired their nails, and the problems went away. I would not recommend these nails, especially for this nailer. ... Read more

Features

• 2-inch finish nails
• 16 gauge
• 2,500 per pack

Reviews (1)

Really Hit The Nail On The Head.....
Great product works great in Bostich nailer. Will purchase again when needed. ... Read more