Product Description

The Lincoln Procut 25 is one handy cutting tool to have around...wether for hobby, farm,HVAC, autobody shop or sheet metal fabrication, this professional-grade plasma cutting system weighing only 29.5 lbs can cut materials up to 3/8" thick. operates on 115V or 230V 60% duty cycle at maximum output assures generous high end capacity ... Read more

Features

• 25amps of cutting power from only a 29.5lb package
• Automatic reconnect between 115V & 230V for easy power connection
• Patented PCT20 torch with VORTECH technology consumables
• Two Year Warranty on parts and labor (one year on torch)
• back lit LED system for staus indicators

Product Description

Solid state design and Miller's reliable technology pack a ton of performance into the portable, 49 pound Spectrum 375 plasma cutter. This versatile power source adapts to the shop or work site by operating on either 115 or 230 volt AC power. This machine can cut 1/2 inch mild steel with a stand off, and can drag cut 3/8 inch mild steel. With new features such as the Pilot Arc Controller, Heavy-duty work clamp, and Ergonomic ICE-27C torch, the Spectrum 375 CutMate is the clear winner in its class. ... Read more

Features

• Drag Cut Rated: 3/8 in...w/Standoff
• Increased Line Voltage Compensation regulates input power to a fixed value
• Dual input voltage located in back of units allows either 115 or 230 VAC
• Starts without high-frequency so it will not interfere with controls or computers.
• Easy-to-connect, built-in gas/air filter and regulator with extra protection.

Product Description

The FP18 is a 110V 1/8" capactity plasma cutting system with an on board air compressor. Simply plug the unit into a 110 volt outlet and the system will 10 cut gauge, 1/8" mild steel at 9 IPM. No more air compressor to haul around. The internal compress ... Read more

Product Description

With the introduction of the FP38, Firepower created a new standard of performance for the sheet metal cutting world. Rugged Design Equipped with a rugged case and a protective roll cage to protect the power control components. Auto Pilot Restar ... Read more

Product Description

Severance cutting .5 in
Infinite amperage adjustment: 15 amps to 40 amps
Instant arc starting without high frequency ... Read more

Features

• Whopping 40 amps of cutting power in a compact cabinet
• Cut any material that conducts electricity
• 220 volt
• 85 cutting volts
• Cuts up to 3/8 in

Product Description

Dual input voltage located in back of unit allows either 115 or 230 VAC input power and provides patented protection in case of incorrect switch position. Unit provides full cutting capacity when powered by most engine driven welders with 240 VAC auxil ... Read more

Product Description

Comes complete with ICE-27C hand-held torch with 20 ft. cable, 15 ft. heavy-duty work cable with clamp, 3 electrodes, 3 tips and 1 air fitting, 10 ft. power cord with 115 VAC 20 A plug ... Read more

Features

• Dual input voltage allows either 115 or 230 VAC
• Starts without high-frequency - will not interfere with controls or computers
• Pilot Arc Controller increases cutting capabilities & speeds
• Postflow cooling circuit extends life of consumables and torch

Product Description

Features: Dual input voltage located in back of unit allows either 115 or 230 VAC input power and provides patented protection in case of incorrect switch position. Unit provides full cutting capacity when powered by most engine-driven welders with 240 VAC auxiliary receptacles. Starts without high-frequency so it will not interfere with controls or computers. Pilot Arc Controller increases cutting capabilities and speeds, and improves tip life. Postflow cooling circuit extends the life of the consumables and torch by cooling them with postflow air after the trigger is released. Line voltage compensation (LVC) provides peak performance power under variable conditions (power fluctuations up to +/- 15%) for steady cuts and cleaner ending cuts. Gas/air filter/regulator inside the power source provides added protection during transportation. Standard air connection on back panel for easy gas or air hookup. Rated Output: 27 A at 90 VDC, 35% Duty Cycle Cutting Capability: Standoff Cutting Rated: 3/8 in.; Quality: 1/2 in.; Sever: 5/8 in. Drag Cutting: Rated: 5/8 in.; Quality: 3/8 in.; Sever: 1/2 in. Plasma Gas Flow/Pressure: 4.5 CFM (129 L/min.) at 60 PSI (414 kPa) Comes complete with: ICE-27C hand-held torch with 20ft. cable 15ft. heavy-duty work cable with clamp Extra consumables (3 electrodes, 3 tips and 1 air fitting) 10ft. power cord with 115 VAC, 20 A plug Free Shipping Available . ... Read more

Product Description

The FP18 is a 110V 1/8 inch capacity plasma cutting system with an on board air compressor. Simply plug the unit into a 110 volt outlet and the system will 10 cut gauge, 1/8 inch mild steel at 9 IPM. No more air compressor to haul around. The internal compressor insures clean, dry air with no need for a filter. Features: Operates on standard 115 volt current Built-in air compressor - Portable & Self Contained! Cuts mild steel, stainless steel, aluminum, copper or brass Weighs only 55 lbs! Features a inchpilot-arc inch that burns through paint and rust Drag tip system allows placement in tight spaces and awkward locations Substantially reduces joint prep time - Warping does not occur and slag removal is not required. Long consumable life/low cost per cut Firepower automatic torch restart system One year Firepower warranty Comes complete with: 20 ft. genuine Firepower drag torch system, 6 ft. power cord with plug, (5) 1445-0031 cutting tips, (3) 1445-0016 electrodes, (1) 1445-0017 gas distributor, instruction manual. Specifications: Input voltage - 115V 60HZ Input current - 20 Amps Maximum output - 18 Amps Rated output - 12 Amps Rated duty cycle - 30% Maximum cutting capacity - 1/8 inch Cutting speed (mild steel) - 20ga./60 inch Per Minute, 18ga./60 inch PM, 10ga./12 inch PM, 1/8 inch/9 inch PM . ... Read more