Features

• 1-year warranty
• Variable speed oscillating tool replaces sanders, saws, putty knives, scrapers and other tools
• Oscillates back and forth at an angle of only 3.2 angular degrees at up to 21,000 OPM
• High abrasive performance right into the furthest corners
• Vibration-free operation

Amazon.com Review

Hitachi's' 8-1/2-inch sliding compound miter saw is a tried-and-true favorite with professionals, who value its solid construction and reliable accuracy. It has a 9-1/2 amp motor with an electric brake, 11 positive miter stops, and 4 positive stops on the bevel gauge. We like the big wide table, the hefty base construction, and the embossed numbers and markers of the miter gauge. While the sliding fence is clearly designed with easy adjustment in mind, it's less durable than we would like to see and not too tall. The blade guard operates smoothly and doesn't obstruct the visibility of the work--an improvement over previous versions that had a tendency to hang up. This saw was among the first sliding compound miter saws out, and its solid, reliable design hasn't changed much or lost popularity, even after several years on the market and a lot more competition. Due to its solid construction, it remains accurate after a long time on the job, making it a consistent favorite with professional trim carpenters and everyone else whose work depends on exactitude. People who want the accuracy this saw offers but need more thickness capacity and the convenience of a double-bevel saw may want to consider Hitachi's 10-inch sliding compound miter saw. --Brian Trinen ... Read more

Features

• Hitachi exclusive 5 year warranty
• Ball-bearing slide system
• Locking swivel head for bevel cutting
• Spindle lock for quick blade changes
• Bevel and miter detents for crown molding cuts

Reviews (20)

Lay it Down
I've owned this saw for over 5 years now and will most likely grab another one for the crew. It doesn't get anymore percise than this unit.We work on exclusive homes on a daily basis that are loaded with sizeable moldings.A little clue to those who try and cut everything standing up, LAY IT DOWN. You can be much more accurate with your molding laying on a flat serface,specificaly large crowns and baseboards.So my advise to Bobby from Boulder is to learn how to use that exspensive saw you speak so pourly of or just work with 3" moldings for the rest of your days.

Great saw- beware though of wrong info above from manufactur
As the owner of a trim carpentry business with 5 employees, I have to admit this saw is the most versatile I have found. Each employee has one entrusted to him, and I have tried the other brands and even own the new 10" Hitachi dual-beveling saw. The point that needs to be made is that the description at this time from the manufacturer says that this saw bevels both directions- which it does not. It miters both directions, but only bevels to the left. The larger ten inch Hitachi bevels both ways, and it a nice saw to own also. The beauty of this saw, though, it that it lasts practically forever, is lightweight, and versatile. We cut up to 24" shelving by cutting one direction, then flipping it over and finishing the cut. We cut miles of crown flat with it using compound mitre and bevel cuts, and it's not a big deal to flip your piece around.(Most of the time, we use a crown that you can flip over and cut due a flat profile instead of handling the long length again) Buy this saw, you will enjoy it.

SOO CLOSE!
Hitachi has come soo close to perfection with this saw. It's small blade, high power motor, and well designed slide mechanism make this saw cut more consistently high quality cuts than any other saw on the market! But, this saw also has some serious weaknesses. 1) Only tilts in one direction. 2) Fence is too short( all cuts must be done flat.) 3. Fence is too soft. becomes bent after relatively short period of constant use. plastic fence pieces break and are tooo flexible. can be remedied by attaching hardwood to fence but this limits the clamp. 4) smaller capacity.

while I say this is the best on the market I have not tried the latest 10" sliders to enter the market.

PLEASE NOTE THAT EVEN WITH THESE DRAWBACKS IF YOU MUST HAVE A SAW TO DO FINISH WORK THIS IS IT. THIS SAW MAKES THE DeWalt SEEM LIKE A TOY!

HITACHI DUST BAG
JUST RECENTLEY STARTED USING THE HITACHI 81/2 SLIDING SAW AND SO FAR IT HAS BEEN VERY GOOD, JUST A COUPLE OF IMPROVEMENTS I WOULD LIKE TO SEE, ONE IS THE 45 DEGREE DETENTS NEED TO BE MORE PRONOUNCED ALSO THE DUST CATCHER NEEDS TO BE IMPROVED I TRIED TO SEAL ALL THE PLACES IT THROWS OUT THE SAW DUST WITH LIMITED SUCESS

Need replacement parts
I own a C8FB that I bought in 1991. Love the saw, it still cuts as good as the day I purchased it. The problem I have is I need a few replacement parts (blade guard, blade insert,etc.)and don't know where to get them. Can anybody help me out? ... Read more

Features

• 4-position stroke control for working with a variety of thicknesses
• Powerful 6.4 amp motor for fast, smooth cutting
• Variable speed trigger for optimal cutting control
• Precision control design for laser straight cutting
• One-Touch Blade Change for less downtime and more productivity

Reviews (7)

No such issues
I bought this saw back in March and have used it quite a bit. My purchase was an upgrade from my old B&D and the difference is night and day. I have not noticed any issue with heat buildup and I have used it to cut through 1.5" thick plywood and 2x4s without issue. Highly recommended.

outstanding quality
I had purchased the metabo top of the line jig saw. It was the most difficult jig saw I ever used. I ended up going back to my 30 year old sears. Finally, I returned it and purchased the 1590. I can not tell you the difference. In quality, in use, the blade changing system is so far superior and the guides are fantastic. The blade is clearly visible and is kept clean by the blower. I did not notice the unit getting hot as was mentioned in one review. If you are serious about your equipment, just buy this jig saw, none can compare.

What a DISAPPOINTMENT!!!!
I owned the 1587 model from Bosch, but sold it to my brother to "upgrade" to the newer model with the simpler blade ejection and the updated blade clamping system. What a mistake!!! As one other reviewer stated, this saw gets very, very hot to the touch. I ran the 1587 next to this model side by side for 1 minute just to see if that reviewer was correct. The 1587 warmed up then cooled itself down with the design of the vents. The 1590 warmed itself up and just kept on getting hotter. At about the 45 second mark, you could no longer hold onto the front of the jigsaw. I love Bosch tools, but this tool has a major design flaw in the way it cools itself. I am now buying the 1584 barrel grip from Bosch. I can't wait to get back to a quality design from a quality company. Bosch can do much better than this product.

very smooth jigsaw
I have had this saw for a few weeks now and am very happy with how smooth it cuts everything. I used it to trim off an overhang on a kitchen counter and it made a very smooth cut through both the laminate and particle board underneath. Also, I have used it to make some cut-outs in the plywood for a sub-floor and the cuts are very smooth. The blower works very well so that you can easily follow your cut line.

This saw is rather heavy for a jigsaw but the weight helps to absorb any vibration. The price and weight are both high but if you want a smooth and powerful jigsaw take a look at this one.

Fast and Accurate
I make a lot of custom furniture as well as perform trim carpentry that requires me to cut molding around brick and rock. I've found the 1590EVSK easy to handle with plenty of strength to consume maple and oak effortlessly. The oscillating blade is a wonderful feature and you can't beat the blade installation and removal.
While it could be considered pricy, if you plan on using a jig saw on a consistent basis this is absolutely one to to put at the top of your list to consider. ... Read more

Features

• Easy adjustable operating pressure on the machine
• Delivers 1750 psi max. pressure at a rate of 1.6 gallons per minute
• Shuts on/off at the trigger gun
• Built in GFCI for safety and thermo-coupler for motor protection
• Pressure regulation from 400psi -1750psi max and equipped with universal storage reel

Reviews (1)

Great Machine
This machine did a great job on my car, house siding and back deck. In the past, I have spent hours cleaning with just a garden hose. The Prowash cut cleaning to one fourth the time it usally had taken me. It was easy to assemble and the manual was very simple and straight forward in explaining the operation of the machine. I had purchased a Home Depot machine two years' ago and the inlet connection which was plastic keep breaking on me so I had given up on electric pressure washers completely until a friend recommend this unit. The inlet connection on the Prowash is metal so I felt my problems were over. It proved to be true. All in all-great machine. I recommend it. ... Read more

Features

• 25ft hi-flex hose stays flexible - will not kink
• Quietest, most powerful, portable, professional 4-stage system
• Fuji XT model non-bleed spraygun
• Stainless steel fluid components
• Insulated stay-cool handle

Reviews (4)

Overall.....impressive
Pluses:

1. Quiet operation - it sounds like a small vacuum cleaner

2. High quality parts - nothing cheap/flimsy here

3. Great quality of finish - consistent quality with paint and
laquers.

Minuses

1. VERY stiff hose - it induces fatigue after a short while which
becomes a bit of a distraction. I plan on changing mine soon

2. Expensive - I got what I paid for so it's not truly a
complaint

Overall I would give this product a 4.5 rating if I could. I'm very satisfied with this product

A great product and Excellent service
Whatever happened to my first review of this product? I can not find it anywhere and I wanted to spread the message about Fuji very much!

I bought a Fuji Q4 about 3 weeks ago and after having waited for long because of a delay in manufacturing due to the release of the new XT Non Bleeder type gun that comes standard with all new Fuji Q3 and Q4 systems.

I opted for the Q4 because for a relatively small difference in price you simply get the most powerful turbine in the market. It is a 4 stage turbine made right here in America. Fuji manages to put this monster in a very steardy black metal case and the system is claimed to be 50% quieter than the competition. Comparing it to a Turbinare unit I was thinking to buy I totally agree with Fuji's claims.

The unit came in a steardy box but to my dismay the plastic fitting that connects the hose to the turbine was broken. In addition to this, the 6 foot Flex hose I had ordered to come with my unit did not show up either.

A simple call to Fuji and a couple of days later I received a box with the Flex hose, a new plastic fitting and a quick coupling compliments of the company. I was also informed that
I would be receiving a new metal fitting as soon as they are available.

I highly recommend any new buyer to get this Flex hose as it really makes spraying a pleasure w/o the burden of the big rubber hose that comes standard with the unit. By the way, my unit also came with the small plastic cups I bought as an additional option and a pack of spares like cup seals and additional strainers.

I used my Fuji to spray 26 restaurant chairs for a friend who is openign up a new restaurant and the unit performed much better than I had anticipated. That time I used the plastic cups only because I had to spray between chair legs and I needed the smaller size of the spray sytem. The finish was as impecable as I ever had using a spray system and with an ease of conntrol I never felt using my compressor powered NON HVLP sprayer. It is such a different experience to have your paint go where you itnend it and STAY there instrad of the mess that a high pressure sustem creates. After spraying the 26 chairs I pretyt much walked away from the job with no paint stuck on me or my clothing.

The next day I had to spray some booths for the same friend and I tried to use the metal cup that comes with the system. Unfortunately, I could not make the gun achieve an good seal and since it is pressurized the paint was oozing out from it. I went back to the plastic cups and finished the job w/o a problem.

Having contacted Fuji again I was told they will be sending me a newer make of a cup and hopefully this problem will also be solved. Please note that since the XT gun and cup assembly is new for Fuji and I guess some problems had to be anticipated. The point here is that the manufacurer is simply AMAZING in responding to comments and lightning fast in taking care of any problems you may have. You get to talk to Paul, the owner himself (not some clerk that could not give a darn about anything) and this guy even responds messages on weekends!

I give the Fuji Q4 a round 5 star for performance even with the few mishaps I had with it. It is super quiet, super powerful, super performing and it is backed up by what I feel is the best customer service I have ever encountered in my 15 years of buying wood working equipment from various big name manufacturers like Delta, Powermatic, Bosch etc. These guys could learn something about customer service from Fuji.

I give Fuji a 4 star for quality control but again, the outstanding service they offer prety much decides it for me: Fuji is an absolute winner! DO NOT buy another HVLP spray system until you try a Fuji first. Highly recommended.

Look no further.......
The Fuji Q4 Pro is QUALITY, top to bottom, A to Z. Unbelievably quiet, VIBRATION FREE, (becoming a rarity in electric motors because apparently no one cares about bearing clearances or endplay) and EASILY powerful enough to spray any finish you want. (the one exception being polyester, i.e. "grand piano" coatings which need a high pressure, (and high overspray) cup gun.)
Fuji industrial is a no-nonsense company. If you call for support, parts, etc., the president and CEO of the company answers the phone himself. No waiting on hold, elevator music and the like. He seeks absolute customer satisfaction, no middlemen and no confusion.
American manufacters should take note of the lack of corporate wigs, board of chairmen and such with their multi-million dollar salaries for doing basically nothing for their company. What suffers naturally is the end product resulting in yet ANOTHER inferior quality, poorly designed domestic product.

And, despite the name "Fuji", the company is based in Ontario and uses over 90% North American content.

At least here, you are paying for PRODUCT, not some 7.5 million a year PR figure while the engineers don't get paid enough to put out a continually improving product.

You will get more than your money's worth with the Fuji. The gun itself is worth more than many complete systems. And as stated, the Q4 is "THE MOST POWERFUL AND QUIETEST SYSTEM ON THE MARKET."

So, if, you want the most from your dollar, as do I, you won't be disappointed here.

Great sprayer, I am very pleased
I have had this unit about 10 months now and I am very happy with it. My goal, in general, was to get a sprayer with the following features/functionality:

-spray fine finishes such as lacquer and water borne finishes
-also spray thin stains as well as occasional latex and oil-based paints
-variable air pressure for more control
-spend less than $1,000

This unit has satisfied those goals very well. The variable air control is really a must, in my opinion, otherwise I cannot adequately control the atomization. This air control works very well on this unit. It does not vary the motor speed, but varies the flow through the hose with a convenient control located at the gun handle - you can vary the flow as you work and fine tune it without having to run back to the compressor unit to make adjustments. I just turn the unit on and then make all the adjustments at the gun.

This unit sprays everything have tried very well: thinned lacquer, straight stains and dyes, latex paint (with Flotrol), and slightly thinned oil base paint. The finishes are extremely smooth.

Once I have the air and fluid controls set for a given project, the amount of overspray is really remarkably small. Although it is possible to create a lot of overspray, that usually means the air control is set to high.

The unit is very easy to clean - usually I just run solvent through the gun after every coat. Then thoroughly clean the needle and nozzle after the project.

A bonus for me is the sound level of the unit - it is really very low - it is like a mid range "whoosh" . Definitely not a loud unit at all. I find that once I have everything adjusted and start spraying, I do not even pay attention to the sound of the unit at all. I understand that some other brands have very irritating noise levels. Not so here.

I also appreciate the manufacturer's after sale support. Very helpful. I also purchased (from Fuji direct) the 6 foot whip hose and the set of small plastic cups for small jobs. The whip hose is very light and I find it very helpful in maneuvering in my small spray area.

I have been happy with the needle/nozzle combination which came with the unit, although my guess for the majority of my lacquer work, the #3 nozzle would work fine also. ... Read more

Amazon.com Review

Known as one of the few quality saws still made in America,what really sets the Powermatic 66 apart from the competition is about200 pounds of solid vibration-reducing cast iron. The weight of thismachine makes it the smoothest-running tool in its class. A 40-pound,single-piece, cast-iron trunnion reduces vibration from the3-horsepower motor. Combine this with the 28-by-38-inch cast-irontabletop and you have one beefy machine weighing in at just under 600pounds. The unique belt-drive system distributes torque moreefficiently with less wasted energy going to heat. Staying cool means alonger motor life and less wasted electricity. The Powermatic 66 has aconvenient, hinged front access door and a 4-inch dust collection portfor easy connection to standard dust collectors. The 50-inch Accu-Fencehas an interior spring that applies constant pressure when not lockeddown, which takes the slop out of fence movement, improving accuracyand the speed of fence adjustments. It also has replaceable sides witheasy-access screws. Users can adjust the sides so close to the tabletopthat laminates will not slip underneath. The Powermatic 66 is theclassic choice for professional cabinetry and furniture shops, as wellas for hobbyists who spend more time in the shop than on the couch.--Nancy Gleason ... Read more

Features

• Includes $292 worth of free options: dado insert, motor cover, extension table, and legs
• Heavy cast-iron trunnion reduce vibration and ensure smoother cuts
• High-efficiency 3VX drive-belt system delivers torque more efficiently and generates less heat
• Left-tilting blade prevents binding during bevel cutting, reducing the risk of kickback
• Award-winning Accu-Fence system creates an easy-gliding, precision fence

Reviews (16)

Rolls Royce of Cabinet Saws
I purchased my 66 in August of 1997. It has been used heavily for the cabinet work in our new log home as well as several other furniture projects. I made the cabinets from hickory and the 66 sliced through this like soft butter. I compared the 66 to the Delta and the Jet. I preferred the left tilt, and the small access door on the front was a nice feature. The Powermatic just seemed to be an all around solid machine. I've not regretted the extra expense for one second. If you want a serious table saw, this baby has what it takes.

Mixed bag
I received the saw and all 7 boxes. Driver was very helpful in delivering directly to shop. From one of the previous reviews I read here, I had put together the mobile base (bought separately) first and was able to move the saw base from the pallet to the mobile base. This is definitely the way to go.

First the good. I had always heard that the Powermatic 66 was the "best". I was impressed by the fit and finish of the saws that I had seen. I still feel that the finish on the top is the best anywhere. The packaging provided good protection. The extension wings went on easily and were easy to align properly. I got the wood extension table and it arrived intact without problem.

Now the not so good. Installing the front rail for the accufence, the instruction manual has you ensure exactly 2 27/32" from table to front rail and that this dimension is critical. However, after attaching the rail to table, it was not possible to achieve this "critical" dimension. Contacting Powermatic by phone(don't try the URL address provided, it doesn't work), they informed me that as long as the offset is consistent from table to rail that acceptable performance can be achieved (i.e., 2 14/16 or 2 13/16 was OK as long as this was consistent along the length of the table. (So much for critical). Not having this info initially cost me a couple hours unnecessary setup time. I also had difficulty getting the guide bar to be a consistent length from the table to the bar. The Powermatic rep(different individual) I contacted assured me that this had never been a problem before. (so I must be making it up?). I started removing mounting bolts from the underneath of the guide bar and found that one of the holes was offset enough to prevent the guide bar from being paralell. Once removed, it was possible to properly align the guide bar.

Once the fence was set up, I attempted to adjust for paralell. I spent a lot of time and was never satisfied with results, but the dimensions from the infeed and outfeed side of blade to the fence were equal or the outfeed was a hair greater. I never got a smooth cut. I assumed that the blade I was using was at fault, and bought a Forrest blade (very nice). I tried again and got better results but still not what I expected. There was always a gap between the wood and the fence on the outfeed side or I would get binding if adjusted the outfeed side further in.

I decided to invest in a rather expensive precision gauge to measure for exact paralell. What I found is that the accufence side plate which is UHMW plastic is concave, going in approximately 8 mils at the center of the cut. I am still working on getting this right, I ought to be able to shim it.

In summary, when the saw is up and running, it is very smooth and powerful. Very heavy arbor, low vibration, excellent lift and tilt mechanisms. The surface finish is excellent, but the fit of the fence was disappointing to say the least. I suspect this will be an excellent tool when finally adjusted. I had an inexpensive craftsman before and required a lot of adjustment and aftermarket add ons to make it work smoothly. I didn't expect the same from Powermatic. I am convinced top quality tools are worth the expense, but I expect top quality. I can recommend the HTC mobile base and the Forrest blade that I bought for this tablesaw, but the verdict on the saw itself is questionable.

Worth spending $400-$600 more
Purchased saw from local dealer paid $50.00 more than online. Couldn't wait shipping time from onlinesale. Fit and finnish excellent, better than Jet, Delta, General and everyone else. You will spend $400 - $600 more over the competitions best, you will never be satisfied untill you own a Powermatic-Bottom line, DO NOT SETTLE FOR ANYTHING LESS. Stock fence with UWOM poly sides is good for zero clearance cuts, but for short stock use a Besiemere with laminite sides. I would recomend this saw to anyone who demands the best and appreciates quality workmanship.

Excellent Machine.... Better save up though.
There is not much to say about this saw that hasn't already been said 1 million times. It's the best out there, but you pay for it. I examined many shops, garages, and woodworking stores before finally investing in the Powermatic, but I would not change anything now that I have it. The fit and finish is perfect, the power is ample, and the cuts are amazing. Combine this machine with a Forrest woodworker II and you're ready for just about anything. It took me a while to get the machine all set-up and the tolerances dialed in, but careful setup leads to successful production. All items arived in good shape, and went together as planned. I used a dial gauge mounted on a miter-gauge insert for all my alignment which was priceless. I measured the arbor flange runout at less that 0.001" at the outer rim of the flange. The only complaint I have is the price.

Unfortunate experience
I had many problems with this saw because of defective parts. The fence rail was bent, the table top was not flat (out 5/32" from side to side). The material on the side of the fence was cupped. Powermatic service did replace all these parts but this isn't where the problems ended. After set up finally was complete,I powered the saw up and a great deal of vibration occurred. Come to find out when the machine was manufactured the set screw on the drive pulley for the blade was missing.So the pulley was drifting on the shaft. Easy fix but by this time I thinkin' lemon. I could write a 100 pages of adjustments and problems I have had with this thing but I will spare you all the details. Just to let you know a little background on myself is I'm a mechanical engineer and have a great deal of understanding when it comes to equipment. This is not what I had expected from Powermatic ... Read more

Features

• One year warranty/30-day performance certification
• 3.7 amp motor for efficient polishing action
• Electronic variable speed
• Random, swirl-free polishing action for a fine finish
• 100% ball bearing construction for durability

Reviews (10)

Great Machine
I just used the machine on my 1996 Ford Probe. It did a great job at removing the swirl marks and bringing out the shine. It didnt remove everything I wanted it to but my paint is 8 years old and may need more aggressive measures. Cut the time of waxing in half because its so easy to remove the wax from the car after it hazes over. Overall, a great buy from a great company.

Polisher
Totally awesome polisher. Lightweight, smooth, and powerful. I have a 30' boat that would typically take all day to wax with a cheap orbital polisher. I can now complete this job in three hours with a much better finish. I use the 7424 to apply wax and the Dewalt polisher to remove and finish the boat. These tools save valuable time and give this boat an incredible finish.

Best Wax Applicator ever
I use it to wax my 45' Boat and three cars. So good, I bought two!!!

Money well spent! Works like a charm! A+++++
Very easy to use, even for someone who's never used a polisher before. I used it on my wife's car which had a Maaco paint job a year earlier. Really brought it up nice. I can't say enough about this machine!!
I used the 3M Finesse-It II Finishing Material Machine Polish to start with and then used Zaino. Here is a pic of my wife's car after it was done.

http://www.67gtx.us/ebay/escort3.jpg

...
Hi All, I am one who can't get a high enough shine and wax protection on my new truck. I am for ever washing/polishing/waxing my new 2003 Suburan truck. At the cost of a viechele today we must maintain them to the best we can!This Porter Cable Orbirter is OUT OF THIS WORLD! It makes a back breaking job SOOOOOOOO much easer and brings up a shine on your vechile that cant be matched. It does this with TOTAL SAFTY of your paint! You never need to worry that the paint will burn or anything.It a light weight easey as can be to work with and we have found the white foam polishing pads made for it by porter cable( Item # 54745) are the BEST! Other co. offer a new screw on velcro head with velcro polishing pads that we have found dont hold and "FLY OFF IN USE". The one from porter cable is a one piece screws in tight polishing head NEVER A PROBLEM with it... ... Read more

Amazon.com

This top-of-the-line 10-inch diamond blade wet saw produces precise, chip-free cuts on all tile, ceramic, marble, and slate. The 115-volt motor develops a peak 1-1/2 horsepower. Better yet, working with big tile is a breeze: this unit cuts a 20-inch tile lengthwise and a 14-inch tile diagonally. The locking blade shaft makes blade-changing a snap. A fully integrated, precision guide bar guarantees smooth travel, while the 10-inch blade gets you a 3-3/4-inch maximum depth of cut, and the professionally engineered high-torque AC 12.8 GE motor and Micro-V belt drive make sure this unit is going to last. The heavy-duty stand is sturdy and dependable, too. In short, this is a beautiful saw package for the exacting professional.--Kris Jensen-Van Heste ... Read more

Features

• Water pump and 10" tile blade are included
• Powerful 115V, 1-1/2 hp GE motor
• Features a shaft lock for safe, easy blade changes
• Cutting depth capacity of 3-1/4
• Can rip cut a full 18" tile while diagonally cutting a 14" tile

Reviews (1)

"Outstanding Tile Saw"
The MK-100 10" 1 1/2HP Tile Saw is an excellant saw for the money. I researched many different brands and sizes of Tile saws. I wanted one that could cut a variety of different types of tile and the ability to diaginaly cut twelve inches. I talked with an MK service rep and he said the MK 100, their newest saw, was basically the same saw as the 101. It does have a different motor and there is no cover over the slide assembly. The MK-100 will cut 12" floor tile in about three seconds. The saw sounds the same as the 101, basically the same machine, just two or three hundred dollars less expensive. The saw comes with a very good instruction booklet and everything needed to cut tile. The Diamond blade could be better, but you can easily replace it when it becomes dull.

I highly recommend this versatile saw to anyone that wants a great saw , at a great price. ... Read more

Features

• Five year limited warranty on machines, parts and accessories
• Includes left tilt, 3 HP single phase motor for powerful cutting
• 50" Biesemeyer commercial fence system
• Carbide tipped 50 tooth ATB&R saw blade, right extension table, adjustable steel support legs
• Two cast iron extension wings, standard insert, miter gage, motor cover and 4" dust connector

Reviews (11)

Top of the line
I bought the 3HP, left tilt Unisaw with 50" Biesemeyer fence, and I'm delighted with it. I had some questions on adjustments, and their tech support personnel were great - prompt and well-informed. The Southern accent was just a nice bonus for this displaced southerner (I work for Yankees, but that doesn't mean I have to like it :).

In contrast with another reviewer, I can't get mine to act up at all. It handles everything I've thrown at it as though I'm asking it to cut 3 sheets of paper, ho-hum. And that includes some long-ish cuts in 2 1/2" thick oak. No thick maple yet, but that's on the docket soon.

There was a warning on the assembly instructions about attaching the extension table legs in a different place if you were using a mobile base. I ignored the instructions and had to remount the legs in the right place (doh!), so be sure you pay attention there.

I waited a while to get this Unisaw, and figure it's the one piece of shop gear I'll never need to replace. Maybe I'll update it in 20 years with the latest laser-guided fence doohickeys or whatever is new then, but the saw and motor will easily outlast me. And I'm not too old or decrepit yet!

Delta Saw
Saw was delivered without difficulty. Package was in good shape. Assembly was not as easy. Extension wings were not labeled left or right, but they were not too hard to level. The splitter assembly was easy but the plastic blade guard is a real pain to work with. It is in the way of everything you want to do on the table surface. The motor cover is very nice but the holding screw is all the way at the bottom so you have to lay on your stomach to see it and get it out.
The Biesemeyer Fence is very well made. However it came without 2 packages of hardware and mounting screws so I had to call and have them sent. That took another 10 days to mount the fence system.
Overall I am very pleased with the saw. I expected a little more QA on the packaging with all needed parts but sometimes it happens.

Excellent product, weak customer service
I purchased my Delta unisaw several months ago and it is everything that I had expected and more. Works like a charm, flat table, easy to assemble, and accessory items mate perfectly. I read a lot of reviews, spoke to a lot of people, and Delta was highly recommended. I was a bit concerned about the overheating and wiring issues some reviewers were having, but this saw runs perfectly. I think some of the reported wiring problems must be a result of not clearly understanding or following directions.

I had a few minor problems during setup (a few missing parts and a minor problem with the sub-base) and had reason to work with Delta customer service, both in Tennesee and the local service center in Ontario, CA. I was not very impressed, as many of the answers I received were wrong or poorly thought out. People on the phone usually were not well informed on the product and had to ask someone else before getting an answer back to me. I tried using email, and the responses were very late and of poor quality (contrast with Grizzly customer service........quick responses to email, couteous and helpful). Over the phone I would often get different answers depending on who I spoke with.

One Amazon reviewer recently mentioned the z-brackets that were missing from his Biesemeyer extension table. He was told that it was the result of a misprint in the manual. I also was missing the angle bracket and z-bracket. After weeks of going in circles with Delta cusomter service, they sent me three of each. So, they do exist and they actually can help for fine leveling adjustment of the extension table. I also did not get the hollow handle for the miter guage, as they shipped a solid metal handle. (It is not really important as I have gone to an Incra miter guage) but I asked them to send me the correct handle. Well, they shipped me three handles (the wrong handles, the same one I already had) but they also shipped me three caps (in a separate bag) that are made for the hollow handle that I had asked them to send. So, it all went in the trash.

If the saw lives up to expectations, I will never have to deal with Delta customer service again. Let's hope.

As I mentioned earlier, I also purchased accessory items (mobile base, outfeed table, t-square blade guard)...and all arrived in good shape, installed easily according to assembly directions, and work well.

Nightmare! I don't know what to do!
I ordered a Delta Saw ( 5 hp version) on March 13, 2004. I received 3 boxes out of 4 on March 29. The freight company told me that they left the other box ( Biesmeyer) in Kansas. I called the freight company today and they told me they could not locate the package. They told me to get in touch with Amazon. Amazon doesn't respond to my e-mails. In the meantime my orders are getting cancelled. What a nightmare!
I heard a lot of good things about this saw. I wish I could use it and write a nice review about it.

Everything I Was Hoping For
I held off for a long time in buying this saw. I looked at as many other alternatives as I could find and I researched everything I could get a hold of. I wanted to be sure I was getting the best for the money and that I was going to have the saw for a long time. The Jet was very appealing but when I called about 13 cabinet shops everyone agreed that the Delta was a better machine. Just to note though, they all thought the Jet was an excellent option if couldn't afford the Delta.

So it came down to value. When you consider that one of the free tools Delta is offering is the mobile base (Which works incredibly well) and it comes with a free, high quality, blade the price is very reasonable.

The assembly was so simple that I am very confused by other reviewers that had problems. I did need someone to hold the extension wings while I bolted them on. But other than that I did it myself with a very big smile on the whole time.

I don't' need to mention the performance nobody ever questions it. ... Read more

Amazon.com Review

When it comes to cutting intricate curves, DeWalt's 20-inch scroll saw delivers precision operation quietly and easily. In fact, everything about the saw is designed for convenience. The on/off switch and speed control, as well as the flexible dust-blowing arm, sit on the upper portion of the front arm, inches away from where you're working, so you don't have to reach around the tool to make adjustments. The wide, teardrop-shaped cast-iron table provides plenty of support for materials and bevels 45 degrees each way, great for tackling tricky inlays and shadow boxes. DeWalt placed the pivot points right up front, rather than in the back, which seems to reduce blade vibration. As with many DeWalt saws, this scroll saw doesn't require tools to change the cutting blades, which means it takes you less time and effort to make those drop-in cuts. --Justin Paul ... Read more

Features

• Tool-free blade changing
• Double parallel-link arm design dramatically reduces vibration and noise
• On-off switch, electronic variable speed located on the front upper arm
• Oversize, cast iron table, bevels 45 degree left & right
• 2-inch depth of cut, 400/1750 SPM

Reviews (15)

Great designed saw
The DeWalt saw is designed and manufactured by Sommervile Design in Canada. They make the Excaliber Scroll saw. The Dewalt Saw is very much like the excaliber in that it has very low vibration and having a very smooth operation. I had a dewalt but had to move up to the excaliber because of the work i produced, unless you use a scroll saw for 6 - 12 hours per day, buy this saw. The only problem I had was the motor could not take the beating i gave it, i cut 3/4 to 1 1/2 thickness wood all the time, althought the saw handled that thickness with ease, it could not keep my pace. If your a hobbiest cutting moderately its a GREAT saw. It has a quick release for the blade and you can change blades in seconds, the blade tension is right there in front, the top arm lifts for getting work on and off the table. Fairly quiet operation. Don't waste your money on the light, its not bright at all and does not help. Assembly is a snap upon getting the saw, just put the table on and your ready to go. I have used everything out there, besides the Excaliber, the dewalt is the next best thing. Whats nice about the dewalt, it has the same design as the excaliber in that like other saws that have the full top and lower arms that ofcourse move up and down, the dewalt like the excaliber has only tips of the arms move, the tips that move are only about 4" long, less moving thus less vibration. Inside the top and bottom arms there is a flat rod that move back and forth that moves the tips up and down. When you get your new dewalt and you see how smooth, quiet, and just about no vibration, imagine a saw twice to 3 times better that the dewalt and you have the Excaliber. I think one of the reasons why the Excaliber can take what i dish out is that it is belt driven, this ofcouse increases the power and the strain on the motor, if the dewalt goes belt driven I'll get another one.

A superior saw for the money.
I took my time before making this purchase. I not only read all the reviews but had an opportunity to check out the saw at a wood show. This saw replaces a Delta scroll saw that I bought 10 years ago. I wanted a saw that was easy to use, with very little vibration. This machine fit the bill. There's hardly any vibration at all. It's one of the quietest tools in my shop. Blade changes and tensioning couldn't be any easier. The electronic speed control is a plus. The saw arrived from Amazon.com in excellent condition. The only assembly was attaching the table. In less than 10 minutes I was scrolling Christmas ornaments. The quality out of the box was excellent. I've put about a hundred hours on the saw so far and I have to say that it is addicting. It was a surprise to find that this tool was not made in China or Taiwan, it's made in Canada. Form and Fit are perfect. I've tried very hard to find something negative to say about this saw and have failed. It's a well made tool, a pleasure to use and I'm looking forward to many years of use.

Wow, what an upgrade!
I originally had a R***i from[local store], purchased because I'd had good luck with all the other R***i tools I have. This was my first scroll saw, learning curve and all that. The light quit, then the upper blade holder broke from the mighty twisting of my feeble arthritic grip, I suppose. Took it back. Now being familiar with scroll saw problems, particularly pierceing cuts / blade handeling, vibration, etc, did more research, decided on the DeWalt design. Great price and shipping time here at Amazon. The DeWalt saw? What a sweet machine this is! Smooth as silk, no vibration compared to other designs until the speed is near the max,quieter than the wife's sewing machine, the table / blade zeroed right out of the box. I'll be happily sawing for years to come on this baby. I will agree with the others though, on the hold down foot, it's the one weak point of the design. Most fretwork guys abandon them anyhow. (Not a reccomended practice.) Some have the scars to prove it!

Great saw with one exception
I recently upgraded from a craftsman to the Dewalt. I have been happy with the almost vibration free operation, easy blade changes, and large 20" bed. The only problem I have had is the hold down foot. Dewalt uses a large hold down foot that is constructed of a bent rod that attaches to one side of the upper saw arm. The attachment of the foot is not very solid. The foot interfears with the view of your work piece and tends to fall down into the cutouts when doing fretwork. This causes your work piece to bind up and then suddenly jump free as you apply more preasure to move the piece. It can be frustrating when working on an intricate piece. Also, the size of the foot makes cutting small pieces almost impossible without removing it all togehter. My old Craftsman had a small V shaped hold down foot that worked very well. If Dewalt would fix this one problem, they would have a great saw.

dewalt dw788 dream machine
I bought this item as a Christmas gift for myself, after the short time it took me to assemble the stand & put the light fixture on , I started to do some delicate inside cuts with this dream machine.Believe me I emailed, called, sent in for information on all the saws I could find, I am glad I bought the dewalt 788 saw. I have no connections with this company, I am just a hobbiest who found a new toy with nothing but joy, for the money you cant go wrong, you'll be impressed with the size of the table to the lack of vibration. ... Read more

Features

• 11 positive stops for improved cutting of crown molding.
• Powerful 15 amp motor that handles every job easily.
• Electronic Speed Control monitors and maintains rpm under load.
• Soft Start feature for smoother and safer start-ups.
• Large turn base ensures a more stable work area.

Amazon.com

You need power, but you don’t want to hoist a ton. Here’s the answer. DeWalt’s revamped 18-volt compact drill/driver delivers on both counts, with a 1/2-inch chuck that grips beefy bits, an 18-position adjustable clutch, and a high-performance motor for the torque you need, packaged in a truly lightweight, comfortable drill. The variable speed has a high and low range for any application, and the reverse switch is right above the curved trigger for easy access. The included charger juices up a spent battery in an hour. We especially like the light weight, even more so because it doesn’t cost in the power department. Lots of pluses: on-board bit storage, two batteries, hard case. We think contractors will be pleased with this drill, especially after a long day.--Kris Jensen-Van Heste ... Read more

Features

• 1/2" single sleeve keyless ratcheting chuck for tighter bit grip
• Compact size: fits into the tightest conditions
• Lightweight design (5.2 lbs.) minimizes user fatigue
• High performance motor delivers 450 in.-lbs. of maximum torque
• Dual speed range: 0-450 / 0-1,500 rpm delivers optimal performance

Reviews (8)

Four Years' Tough
I have two of these drills. Have used one or the other of them daily for three years this month. About time for a review. They are tough. I do not understand the comments about weak chucks or, in other places, about battery problems. My drills, their batteries and chargers have performed, as I say, on a daily basis for three years under all kinds of conditions and some very hard use without so much as a glitch. They have tremendous torque and staying power under continuous use. If you are going to shoot large screws or drive a big bit rapidly into very hard or though wood, brace the drill-driver's grip, battery end against your knee or thigh before you squeeze the trigger. You will have fewer wrist problems if you do--it has that kind of torque. Regarding one complaint, I would not use this driver with tiny drill bits; it just is not intended for that. It defies logic to do so. What it will do is take the heaviest work and drive large bits and sink big screws all day and just keep on going. An example: In the intense, 100 degree plus heat of one summer, two carpenter friends and I laid a 1700 sq foot subfloor of 2X6 T&G over 16" OC joists with two 3-1/2 inch screws to the joist, working as fast as we could all day for what seems now like several days. The wood was very tough, dense struc select Doug fir. When my two friends' drivers, one a Makita and one a Hitachi, got hot as pistols or their batteries needed recharging, whichever of the DeWalts I happened to be using could keep right on going. I would lend the other DeWalt to either guy while his driver recovered. I smoked those batteries, but by following the right charging procedures never had a failure. They both still take deep cycle charges and hold them well, after three years of hard use. One took a fourteen foot fall off a roof while mounted to another DeWalt tool, the battery taking the full impact on tamped crushed rock, and it still works as well as the others. Just read the instructions and you will not have trouble with the batteries. Quick charge when you have to, but balance that with long charges from a low state over the weekends. Never use the batteries while they are still warm or hot out of the charger, do not run them out completely--just nearly so, and do not repeatedly shallow charge them. Nicads will not last long with that kind of treatment. They take a "set" and will not charge deeply afterward. As for weak chucks, well, one incident does not make them all that way. When my drywall zipgun stripped its chuck, I picked up one of my DeWalt 18V drill-drivers and kept on going--for over 300 sheets of 1/2 and 5/8 inch drywall. The clutch and speed mechanisms work well enough that I had good control and could hang drywall almost as fast as with the zipgun. One caution regarding the clutches on these brutes: they require breaking in; don't be upset if they are hard to use at first. You can see from this what DeWalt 18V drill-drivers have done and can do, and still I have not had the slightest problem, though they look pretty beat up now. I do not think a single work day has passed in which I have not used one of the two. Now I have a whole lot of DeWalt HD 18V tools, because these two drill-drivers performed so well I was not afraid to buy into a lot of tools in the same line. I have had no trouble with any of them. You never lose them, either; that DeWalt yellow shouts at you from across the room, across the lot or from under a pile of tools and offcuts. When these go, I will buy more.

Great drill/driver
I have had this drill for about six months and am very happy with it. I am a homeowner so I can't speak as to how this drill would function during all day use. For projects around my house it has plenty of power although, like every other cordless tool I have used, it needs a little more time drilling/driving through hard wood. If I want to drill through something thick and tough, I used a beefier corded drill. So far, I have not noticed any of the battery life problems discussed by other reviewers.

I picked up a set of the Dewalt hex shank bits and have not noticed any slippage. The only time I have had a complaint with the drill was while using a hole saw to install locksets in two doors. Of the four holes, the bit slipped out of the chuck two times. Once I reinserted the hole saw it went right on through the door. I don't know if I didn't get the chuck tight enough or if the chuck just prefers the hex shank bits.

All in all a great drill. I can't imagine ever installing curtain rods, assembling bookcases, etc. with a corded drill and/or screwdriver again!

Yet another over-priced, under-achiever from big yellow
This drill is, in short, a dud. I bought it somewhat hesitantly on the recommendation of a friend. I had been looking at this and the Milwaukee and Bosch equivalents but went ahead and took the plunge. What a mistake. It seems to have sufficient torque but the chuck started to wobble almost immediately after only a few weeks of light use. It makes a grinding noise in the low speed setting that I can't seem to find and one of the batteries ... died after only 2-3 months use. Since then the charger .... has also given up making it cheaper to buy a whole new kit (probably what dewalt has in mind anyway). I have since bought the Milwaukee 0624-20 (kit 0624-24)and have been abusing that workhorse for over a year now with phenomenal results while this piece of crap collects dust on the shelf. Not only are the batteries ..... and charger .... cheaper to replace by some $40 but they also last a _lot_ longer. I wish now I had gone with my gut instinct in the first place. Save yourself a lot of grief and money and go for the Milwaukee. You will not be sorry.

quaility control
i have owned three of these drills over the last seven years,i was very impressed the first time i used the 18 volt drill about five years ago and immeadiatly bought one. since that time i have noticed a serious decline in craftsmanship and customer service on DeWalt's part. the chucks spin on expensive drill bits damaging the bit,the battery packs seem to have unreliable longievity issues. the final straw was a blown charger after approx. 40 hrs. plug in time,right in the middle of a elaborate garage remodel. i am going to start phaseing out my DeWalt cordless tools in my personal tool chest as well as the ones owned by the Parks and Recreation Dept. I am in charge of.

Good drill for the money
I purchased this drill as part of a drill/saw combo at Home Depot for $199 so go there for a better deal. I bought this drill to compliment the 18V Dewalt pistol handle drill I already have.

I know what your thinking, why do I need two drills? Have you every tried to drill/drive in between stud cavities with a pistol grip?? Pain in the bottom to do, so when I have that type of work to do I just grab this one, now onto my review.

Plenty of power for anything you may want to do, drives screws like a champ, drills through 4x4 PT with 1 1/2" spade bit with no problems. A great drill at a great price. Since I own their more expensive model I will point out the differences. No hammer action, only 2 speed(don't need the third speed), 2 piece chuck versus the 1 piece, and the handle doesn't have those nice rubber inserts.

Doesn't handle small bits that well due to the chuck design, and the trigger sticks a little when trying to slowly advance it.
One piece of advice, before you even use the drill for the first time grab some athletic tape(Walmart sells black athletic tape so it doesn't look retarded) and wrap it a couple of time around the handle. That improves the grip 100%, trust me.

Even though I did bash some things this is still a awesome drill. ... Read more

Features

• 3-speed
• Electrostatic prefilter cleans dust, bacteria, fungi, and pollen from the air
• view all Air-Tech settiRemote control allows you to view all Air-Tech settings in the palm of your hand
• Removes 99% of particles
• Lifetime warranty

Reviews (31)

Top shelf product!
I've been using the JDS 750 for a almost 2 years now and I'm still very happy with it. I added the charcoal filter for days when I'm finishing. The helpful people at JDS told me that to to extend the life of the charcoal filter, keep it in a plastic bag when I'm not using it.

I just purchased a retro-fit kit to add the remote control and shut-off timer features. Originally, I though the remote wouldn't be necessary but after using the unit for a while it seems it would be more convenient to have the remote. Plus the shut-off timer is a great help. I've left my unit on overnight more than once...

The competing Jet and Delta units are also nice. I checked them both out at shows and local stores. I thought the fit and finish of the Delta unit was not quite up to par with either the JDS or Jet units. This could certainly have more to do with how the Delta units I have seen were handled by resellers rather than anything to do with Delta. I own many Delta products and they are a fine company so I suppose you'll have to use your own judgement on this point.

Customer service from JDS is great. They happily answered all of my questions any time I called.

All three units seem to have similar features but what made my decision was the fact that JDS specializes in this area and their customer service is excellent.

High Quality, Great Value
I locally purchased the Delta Air Cleaner prior to this unit based on price. Once getting it home I realized that I had given up many features to save a few dollars. I returned the Delta and got this unit, it was worth it!

The JDS quality of build is far above the Delta. Heavier gage case and better attention to detail in manufacture. The eloctrostatic air filter is a real value (since it is the outer filter that needs the most frequent replacing/cleaning), and the infinitely variable speed adjustment and pull switch all make this unit well worth the little extra money. The pull switch will half whatever setting you have as high on the variable speed adjustment (each pull is - high, mid, off).

I have reviewed the Jet product as well (only in literature, not hands on) and feel that the JDS is still a better unit. The Jet has the remote control feature which sounds good at first. I have a stereo in my shop that has a remote, never use it. It's never in a convenient place relative to me or I can't find it! I feel the remote for the air cleaner would be the same, and I feel it's just one more gizmo to break or get lost. The air cleaner goes on and off only once a day, no big deal.

It would be nice if the JDS had a timer as does the Jet, but it's an easy addition if I find it necessary.

The JDS says lifetime warranty, that's on the case only, the motor is 1 year. Not sure about the other brands.

One more little thing. I've worked to create a nice atmosphere in my shop and I really dislike products that are sticker laden billboards for the manufacturer. I felt the Delta was an eyesore hanging from my ceiling and the Jet looks to be the same from the pictures. The JDS is subdued and professional looking, a small thing indeed, but perhaps something to consider if you dislike visually obtrusive logoism.

I would buy this unit again and highly recommend it as a necessary safety item in any dust laden environment.

High Quality control, very satisfied
I ordered the JDS before Frank Weston posted his report, I was a bit alarmed after reading the report. I did get the JDS the next day. I found that the machine included all the parts, and it did run very smoothly. It had a slight dent on one corner, this is from shipping damage (as the box is crumpled on one corner), but this is not very obvious when it is installed. I am very happy with the air cleaner, the speed control lets you go from almost silent to a loud rush of air. I leave it on the middle setting, at this speed it is quiet, and moves quite a bit of air. It was difficult to mount on the ceiling due to the weight of the unit (75 lbs) and size. I would suggest that you have someone help you install it. It took about 20 minutes to install. I hung it from the rafters with chain, using the included hardware and chain purchased elsewhere. The mounting hardware included: 4 eye bolts to connect to the unit, and 4 screws/hooks to mount to the ceiling. You can fine tune the eye bolts that connect to the unit, this helps out with leveling. I would suggest that the person with the poor experience call up JDS, it seems like he may have a used/returned unit. I spoke to friends that have the same unit, and none have had any problems whatsoever.

Shipped Short
The air cleaner works superbly. It is a 5-star unit, and the remote and extended run time with auto shutoff are great. It is quiet and really does get the dust out. I highly recommend it. Be careful hanging it if you are doing it by yourself.

Orginally it was shipped without the electrostatic air filter that was supposed to come with it. Also, it came with no instructions - but not hard to figure out. I thought - and still do - that it was inordinately difficult to contact Amazon about this type of problem on the website. (Lots of "let us direct you to returns/additional orders/cancellations," etc., but the "problem with order button, NOT involving a return, cancellation, re-order" took some searching. Note: It is about 3 "layers" down.) BUT - after considerable searching, I did manage to get someone to answer my complaint - and they did it promptly. (5 stars for the service/3 1/2 stars for QC on the orginal order and for the difficults in reporting the problem.)

Amazon sent me an activated charcoal filter free of charge. That is excellent service, and I appreciate it (five stars). I will purchase the electrostatic filter now for the complete set and break even. Anyway - Thanks Amazon. Now modify your website to be more user-friendly for reporting any shortages/damages, etc., and your service will be OUTSTANDING.

Really good for a moderate size shop
I installed the JDS 750 about a month ago. I was in the middle of a major cleanup of the shop that raised a lot of dust, so when I went to dinner, I let the JDS run for an hour and when I returned, the air in the shop SMELLED CLEAN! I have pretty good ventillation, but this was a very major improvement.

The remote control with auto shutoff timer is great, and its very nice that they include a wall mount bracket for the remote so it doesnt get lost in the normal shop clutter. I had looked at other air cleaners before and was not thrilled with having to install an new wall switch and wiring to control the cleaner.

The unit is pretty large, so make sure you have room for it. Its heavy, so was a bit of a challenge to get it up to the ceiling mount I made for it.

The only reason I dont give it 5 stars is that it is noisier than I would like on its low speed. Its not loud, but I wish it had the low speed so it was quieter. ... Read more

Amazon.com Review

Powermatic's model 66 table saw is a beautiful thing right out of the box, its high-grade cast-iron top machine-polished to a mirror finish. For a second, it almost looks too good to use for work--but only for a second. This is a piece of shop equipment that makes a toolhound's heart beat faster. The saw's big table (28 by 38 inches) is impressively thick and durable, so it will stay flat and true. With the heaviest cast-iron trunnion of any 10-inch saw on the market, the model 66 virtually snuffs out all vibration. The double drive-belt system, hooked up to the burly 5-horsepower motor, delivers pretty astonishing power to the blade; we tried everything we could think of--including a big hunk of oak two-by--but the blade never bogged down for a second. A C-flange mount takes the weight of the motor, so the blade cranks up or down easily without the extra weight. The saw's hand wheels are also made of cast iron and have excellent clearance.

The heart of any table saw, arguably, is the fence--and Powermatic's model 66 sports the award-winning Accu-Fence, a system that uses only two moving parts to create easy-gliding, precision, no-budge fence action. The left-tilting blade tilts away from the fence, which helps prevent kickback and binding of the stock, making for smoother cuts. The two-sided blade guards work independently of each other, so the blade is always covered. The guards also swing totally out of the way to make blade changes easy. Behind the blade, there are antikickback pawls for added safety. The saw's base has a clean-out door, allowing you easy access to the saw body and making cleanup a snap--no reaching around the saw components or having to remove the motor cover. You'll also receive a load of extras, including a dado insert, a motor cover, and an extension table and legs. Admittedly, this isn't a cheap saw; without a doubt, however, it is an excellent one that would make a great addition to any shop. --Jon Groebner ... Read more

Features

• High efficiency belt system
• Heavy-duty one piece cast-iron trunion for superior stability
• Left tilt blade prevents binding and reduces tear-out
• Heavy construction throughout to reduce vibration
• Fan-cooled enclosed motor for protection from dust

Reviews (14)

A Powerful, Precision Tool.
After having had several contractor type table saws, that were all generally underpowered and had imprecise fences, I recently stepped up to the Powermatic Model 66, 5hp, single phase, table saw. At last I have a powerful, precision tool that is the keystone of my woodworking shop.

The quality of this machine is first rate. It was well packaged from the factory and set up easily. (Insist on a lift gate delivery).

The front fence rail was a bit off 90 degrees, but was quickly and courteously replaced by Powermatic customer service inside of a week. The new rail is perfect and holds the fence tube parallel to the table top thus facilitating a true fence alignment.

For me, this machine has no negatives. There were no shortcuts taken in either it's design or manufacture. Virtually everything on this machine is adjustable. Fine tuning the machine, once it is in place and set up, is minimal and straight forward.

The Biesemeyer type fence is beyond reproach. The cast table top and wings are flat and true. The mobil base allows you to move the machine easily, with one hand, anywhere in your work space. With the 5hp motor, nothing inhibits this machine.

If your needs include a powerful, precise, high quality table saw, choose the Powermatic Model 66. It's a real beauty.

Powermatic 66 the Rolls Royce of Table Saws
I purchased the 5 HP 1 Phase Model 66. Installation of the cast iron wings and the extension table was straightforward. The cast iron top was polished to a mirror finish and was dead flat. The saw blade was aligned with the miter slots to within 0.002 in. right out of the crate. The Accu-Fence, a Biesemeyer clone was easy to adjust and has been rock solid and very accurate so far. One of the best attributes of this saw is the lack of vibration due to the massive cast iron trunion. The 5 HP motor can easily digest thick hardwoods (I recently sawed a large amount of 12/4 curly cherry without a hiccup). The motor never bogs down. The stock blade guard is hopeless so I purchased an aftermarket overarm guard. I also recommend the Biesemeyer removeable splitter, but make sure that if you order this saw that you have Amazon order the new Biesemeyer splitter that has been redesigned for the Model 66's manufactured after August 2000. This saw is quiet, powerful, and very accurate. Without question this will be the last cabinet saw you will ever buy if you take care of it. The Powermatic 66 is truly the Rolls Royce of table saws.

Three years and running great!
OK, so I used that same title for another review! Its' true. This ACTUALLY showed up on time, ACTUALLY was packaged nicely, and has ACTAULLY lived up to its hype. The 5hp is overkill, but I like that. Smooth, stable, quiet, good dust control, GREAT fence. The fence was adjusted when we set the saw up three years ago and it needed its first tweak about six months ago. That's it. I run ply, MDF, and various hardwoods without even a change of pitch from the motor. I use an 8" Frued Dado with no problems at all. I use this saw commercially and I highly reccommend it!

Powermatic 66 Review
This saw is one of smoothest, quietest, accurate running saw I have had the pleasure of using. I highly recommend it to anyone that wants a saw in the "Cadillac" category.

Powermatic 66
I did alot of homework before I purchased the Powermatic 66. I ordered it on a Monday from the Tool Crib and received it on Thursday. Everything was packaged securely and arrived in 6 boxes. I am waiting for the mobile base to arrive so I can put it together. I am very pleased with the service from the Tool Crib and their shipper FedEx. FedEx unloaded it from the truck and placed it in my shop. Fast and friendly all around. A+++ ... Read more

Features

• Runs on your home's fuel system - Natural gas or LP gas and automatically exercises itself once a week for 12 minutes
• 12,000/12,000 watt model with 12 circuits that is completely pre-packaged for easy installation
• System supplies back up power within 30 seconds, so you won't have to lift a finger when utility power fails
• Includes: Automatic Transfer Switch with built-in emergency load center, 30 ft. and 2 ft. pre-wired conduits, pre-wired external connection box, composite mounting pad, 1 ft. flexible fuel line and "Do-It-Yourself Instalation Guide"
• Powerful OHVI overhead valve industrial engine with pressurized lubrication and oil filter for long life

Reviews (4)

Professional Installation Only
I have the 1999 model of the Generac Guardian 15kw system. This one is hooked directly into my panel and I have a subpanel hooked to the transfer switch. If you think you are going to buy a whole-house generator system such as this one you had better be a licensed electrician, pull all the permits, and have an electrical inspector (and gas inspector) licensed in your jurisdiction. You also better be licensed to plumb gas lines. If you don't, you could unknowingly risk the lives of the electric company employees and blow up your house. So many do-it-yourselfers think they know how electricity works but really have no idea--when you have the licensed electrician install this unit ask him for some horror stories.

On the bright side, this is a real generator, not a joke Home Depot portable. This generator provides two legs of 120v (240v) so it can run your entire house and several 240v appliances. Mine runs all circuits, including the hot water heater, but not the electric stove or the heat pump (a heat pump consumes 5 kw already, which brings you to the next higher Generac which is excessively cost-prohibitive.)

During Hurricane Isabel we ran our entire house for 5 days and ran an extension cord to run a neighbor's refrigerator for most of that time. We had hot water and every home comfort available to us except the electric stove and heat/AC. If you can swing the installation costs of such a unit (which easily costs more than the unit itself) by all means get this unit but if you intend to install it yourself you are a fool.

For people who don't have natural gas you will need to change out the regulator. I use propane so we needed a different orifice. Another reviewer stated that he needed a separate gas meter but I've not heard anything about that from our installer when we talked about natural gas vs. propane. If have a combination regulator and gas meter then the gas company needs to visit. If you have a separate regulator then you need to tap the line for your generator and its regulator before your house's regulator.

remark to prvious post
Page 7 of the online owners manual says that it requires 11-14 inches of water column and that it is the end users responsability to obtina this.

12000 REVIEW
THE ON-LINE INSTRUCTION MANUAL MADE NO MENTION OF 11 TO 14 INCHES OF GAS PRESSURE. ILLINOIS PWR CO WANTS $1600.00 FOR THAT SERVICE, BUT THEY WILL GIVE ME 11 INCHES AT NO COST AND I AM GOING TO TRY THAT. I HAVE YET TO INSTALL THE GENERATOR. THE ON-LINE MANUAL ALSO SAID IT WAS 30 HP AND IT IS 26 HP, BUT HAS THE SAME DISPLACEMENT AS THE 15 KW UNIT AT 30 HP, I DON'T UNDERSTAND. I THINK THE BUYER IS NOT GETTING ALL THE INFO NEEDED FROM THE ON-LINE MANUAL AND I HAVE RECEIVED NO INFO ON THE $100.00 REBATE. THE UNIT LOOKS GOOD BUT NEEDS AN HOUR METER TO HELP KEEP TRACK OF MAINTENANCE.

Fantastic product but you need a high pressure gas meter
This is a good product, it works really well and is super nice in that it has everything that you need included.
That said - this product requires that you have a high pressure gas meter so know that going in and realize that it'll cost a little money ($100 - $1000 depending on where you are and how much other gas stuff (furnaces etc) you have that will need to be regulated back down) and involve a little bit of hassle to get a high pressure gas meter installed. I didn't see that mentioned anywhere and only figured it out after receiving the generator. Double check with you gas provider to be sure that you can get this and figure out what it will cost before you order!
Other than that, I think this is the greatest thing since sliced bread, you can literally run your house/business off it during electric outages. ... Read more

Amazon.com Review

If your projects require you to drill with big bits or if you find yourself attempting to drill with precision under questionable circumstances, this heavy-duty 16-1/2-inch drill press from Delta will help you get out of your, um, hole. Running off a 3/4-horsepower motor that can be wired for either 115 or 230 volts, it gives you an impressive deep plunge length of 4-7/8 inches and holds up to 5/8-inch-diameter bits. Solid cast-iron construction and a 3-1/8-inch column give it the industrial feel and durability we look for in this type of tool. You'll enjoy the rotating work base--which bevels, of course, 45 degrees each way for drilling angles--as well as the depth stop that can be set quickly and easily with microadjustments and a locking mechanism, great for repetitive drilling. While other models sometimes place hard-to-read speed and belt charts under the top cap, Delta uses a wide, clearly legible chart to explain how to configure the belts for each of 16 speeds (215 to 2,720 rpm). And, thanks to the smooth, cool-running induction motor inside, you're not likely to find yourself shopping for a drill press again for an extremely long time. --Justin Paul ... Read more

Features

• 3/4 hp induction motor for powerful, smooth running operation
• 16 speeds from 215 to 2720 rpm for drilling a variety of materials
• 5/8-inch chuck for use with a wide variety of drill bits
• Two-year limited warranty on machines, parts, and accessories

Reviews (31)

Thoughts on my new Delta Drill press
This tool is great, not perfect, but still great. It is well designed and well built. Not many consumer products have
this much cast iron and steel. The tool is heavy, stable, quiet and cuts great holes. I had a little bench drill press for 20 years, and now realize what a waste that was. This Delta would be better with some kind of quick release to raise and lower the table by hand (now you have to crank up and down the shaft). Jet advertises such a feature on their model. Also, the Delta table does not pivot out of the way easily, and does not tilt easily--too many steps and hard to reach bolt.

Wished I had bought this long ago. As a hint, get a set of carbide tipped Forstener bits, as they work great--much better than the spade bits I used to use.

Delta has a good manual, and knows how to design tools. Give it a try. Do wish I could afford a variable speed model, as the belt adjusting looks inconvenient, and I will stickw with whatever speed was set at the factory.

Essential Tool for Serious Woodworker
I have had this floor model drill press for over 2 years and love it. I think that Delta makes some of the best tools in the business. While the cost of the drill press originally made me think twice about purchasing it, I am glad that I did. While trying to decide whether to shell out so much money for a tool that basically a cheap hand drill could do was a bit of concern. That notion was very incorrect on my part. A hand drill can not come close to making accurate holes and mortises as this tool can. I love using it for mortises, and I even make them without the use of a mortising attachment. I set up the fence and equip the drill with a forstener bit and drill numerous holes, moving the wood over very slightly each pass. This technique seems crude, but I feel it works better than a mortising attachment. If you do enough passes it can practically be flat enough so you don't even have to remove the excess with a chisel.

PROS:
* Accurate holes and mortises
* Heavyweight so it doesn't move around easily when working
* Runs smoothly (especially when converted to run on 220V of electricity - which I highly recommend for ALL shop tools)
* Very easy to change the belts to make it run different speeds

CONS:
* Somewhat awkward to attach a fence to the table
* Pricey (but worth it over time)

Overall, a great tool for any serious woodworker. I think there is only two major shop tools that are more critical to your shop, a good table saw and a floor model jointer. Get a good quality drill press ilke this and you won't regret it!

A Good Machine At The Right Price
One doesn't wax poetic about drill presses. They perform some functions that are vital to a workshop, but their primary function - to bore straight and true holes into a variety of materials is hardly glamorous. And not one has ever thought to make a drill press look like anything other than it is. And yet, without one, craftsfolk would be limited in what they can do.

The Delta 17-965 is intended to be an economic entry into the range of heavy duty presses. As such it is primarily for woodworking and light metal work. It lacks the architecture and high precision for exacting machining. But it comes very, very close and at a price that makes it a reasonable entry in an economical shop. It also is sold as the Delta ShopMaster DP400.

Basic features are a 3/4 horsepower engine, a 5/8" capacity chuch, rack and pinion table movements and an external depth stop. It is capable of 16 spindle speeds (215 to 2720 RPM), changes manual via the pulley belts. The table can be tilted 45 degrees left or right. The quill can travel 4-7/8", but if you are using the mortising attachment you will need to shift the depth stop up out of the way, which will cost you about an inch.

An early warning for people used to manhandling a benchtop press. Most of the 195 pounds of this press's weight is in the head - particularly the motor. Delta designed the head so that there is no easy way to get a grip on it. Assembly should really be a two person job. I'm not a weight lifter, and getting the head down into my workroom was a near disaster. And then I had to winch up the head so that I could lower it on the stand.

It works beautifully. I've been cutting long pegs out of Honduran rosewood for a project, which takes a lot of torque and precision. It has worked smoothly throughout. The mortising attachment also works beautifully. For the price this is a tremendous amount of drill press. You could spend more and be less satisfied.

Probably best in the fly-weight class
I'm considering this press as a replacement to my old drill press - various friends own a mix of Delta's, Jet's and General's in the 16"-18" range and I've tried them all. This Delta won the Editor's Choice in a review of low-end drill presses in one of the woodworking mags last year, largely on the basis of low run-out, superior quill control and travel, ease of adjustment and alignment. Delta has a sale on this until mid-April 2004 through my local dealer at $369 with a free 17-924 hollow mortise kit - not needed by me (I use a General mortiser), but a cheap leg up for those interested in trying mortises.

Jim from Douglas, WY: Some improvement can always be gotten by dismounting the chuck, carefully cleaning it and refitting it - all factories are carelessly-quick in final assembly, even on critical aspects like this. Your run-out of .0015" is commonly thought to be better than required for fine-fit woodworking, my goal. You must be a machinist, but this press is way underweight for most metalwork.

I really like this drill press
I've been slowly replacing my lower level (cheaper) woodworking tools with higher quality ones. This drill press was just about my last one because I thought the little bench top Craftsman drill press I had was just fine. I had no idea how much difference a high quality drill press can make in everything you do with it. It was easy to assemble with a little help from my son and the only thing I see wrong at all is a pulley misalighnment which I haven't fixed yet but plan to soon. The adjustments and accuracy are excellent with the possible exception of the table tilting mechanism. I don't use it much so it's not a real big deal but I'm certain it could be engineered a littl better.

I bought mine at a local woodworking store, the price was actually $20.00 cheaper than Amazon and I didn't have to pay shipping. They just loaded it in my Minivan and I felt good because I'm supporting my local merchant plus I'm saving money and if I have a problem I just talk to them and they help me. I can't understand why anyone would buy mail order for something big like this. ... Read more

Features

• Precisely drives staples at proper angle and depth
• High-speed, mallet-actuated pneumatic operation increases productivity over manually-operated tools
• Adjustable to material thickness and tongue positions
• Eliminates hammer marks
• Long reach handle for increased comfort and added control

Reviews (15)

Some things are just built and designed better!
I purchased this nailer from Amazon to lay 3/4" hardwood flooring in several rooms in my house. I have since fired about 5000 staples through it without any problems whatsoever. This stapler is very well designed ergonomically and mechanically. The mallet is big and somewhat massive in weight but there is a purpose in that. It takes very little effort and just a slight tap to drive a staple because it is pneumatic. So if a board lays nice and straight, then a slight tap will suffice, but if you have a somewhat uncooperative piece of flooring, then you will appreciate the heft of the mallet because it will cause the most finicky of boards to come together and lay tightly. The handle is long and fits well in your hand. Consequently your not bent over as much. My first floor laid was oak and I've started my second which is brazillian cherry. This wood is extremely heavy and dense. This stapler does not care how hard the wood is, it just works and flawlessly at that. After all isn't that what you want from a tool, flawless performance!

A Do-it-yourself-er's Initial Thoughts
I purchased the MIIIFS stapler to lay approximately 1,700 sq. ft. of 3/4 inch red oak flooring in my new home. After installing well over 1,400 sq. ft. here are some of my observations:

1) The tool makes it very easy for a novice to put down a nice, tight hardwood floor. If the boards are laying tight an easy swing of the mallet is all it takes to fully seat a staple (more on this later). If the board is warped the MIIIFS can stand up to a solid mallet smack without any trouble. The mallet's plastic face, by the way, does not show any signs of cracking so far.

2) The stapler efficiently uses the its air so you do not need a big compressor. I have been using a 1.5 hp unit with a 6 gallon tank. Output is set at 85 psi. I doubt such a small compressor could supply two nailers simultaneously, but it handles one quite nicely.

3) The stapler did develop a small air leak near the top shortly after I began using it. The amount of leaking is small (based on psi drop at the compressor) but does make a distracting noise. This leak does not affect the function or reliability.

4) At your starting wall you need to face nail the flooring until you get about 6 inches from the wall. After that you'll have enough room to get the stapler into position.

5) As you approach the far wall the stapler can be used up to the last 13 or 14 inches.

6) As mentioned earlier the tool only requires an easy mallet smack. However, if you don't swing firmly enough the staple will not seat fully. This is usually caused by crowding against the far wall and not having enough room to swing the mallet.

7) The firing knob is too stiff to actuate by hand reliably - the mallet is required. It would have been nice if there was a way to trigger the stapler by hand then you could use it much closer to the far wall.

8) I have not had any problems with jamming. The unit I've been using has reliably shot every staple right down to the very last one in the magazine.

9) I have heard some rumors of staple-style flooring nailers damaging the floor's tongue. After closely examining several hundred staples in oak I'd say that about 2 or 3 percent show any signs of tongue damage. Some of this infrequent damage is due to stapling through a knot or due to handling. Some is due to the MIIIFS. I'm not sure how this compares to nail-style nailers. Anytime you send a fastener through kiln dried hardwood you're bound to have some occassional splitting.

Would I buy the MIIIFS again? You bet I would. Despite its few minor shortcomings this tool has saved me a LOT of work and the price is lower than other pnuematic nailers that I've looked at.

Bostitch flooring stapler
The cadillac of flooring staplers! Anyone can put down hardwood flooring like a pro with this one. Would have liked to had a case included, instead of the cardboard box it came in. I guess that doesn't affect the performace, although protecting the stapler could prevent problems down the road.

Need it, Get it!
I did 750 sqft of oak. not one problem, great tool, did not have the misfire problem on last stables. no break downs, perfect every time. Loaned out to friend, expect the same results. will be selling it used shortly. (I don't need it anymore), and will recoup a bit of my costs. Bob

Bostitch M111FS 3\4" flooring nailer
I've been installing hardwood floors for 22 years or so and I'am in need of another nailer. These are a little heavy but can really fly on the big open rooms. The problem is their to expensive. The reconditioned ones are perfect. I started my company 20 some years ago and used power nailers wich are fine and recently went to air powered nailers about 10 years ago. I see no savings on line what so ever except the reconditioned ones that can be repaired on the job site with a $20.00 kit. My Regards Rem. ... Read more

Features

• Includes cast iron router top, fence, insert plate, and hardware
• Mounts to almost any right-tilt 10" table saw
• Accepts Feather-Loc featherboards, Panel-Loc, and fence riser options
• Fully adjustable miter track with 3/4" miter gauge t-slot and accessory t-slot
• Flat, square and true fence stows away when not in use

Reviews (9)

Garage Shop SPACE SAVER!!!!!!!!!!!!!
I just received this 40-031 and was amazed at how easy it was to install. It was a little heavy but I put the center bolt in first and just swung it level and put the other 2 bolts in. I have a Delta Grand Series Contractors Saw and it matches up to the saw perfectly. Of course I was covered in oil after installation. All parts were there and a few extra set screws and bolts came with it. It may have taken me 30 or so minutes to install by myself. Now I can get rid of my cabinet style router table and open up some more space. The only small gripe about Bench Dog is that I called them to ask a question at around 1:00 pm and had to leave a message for the tech guy to call me back and I didn't get a returned call until the next day at 4:30pm. But he answered my questions and was very nice. DON'T HESITATE TO BUY THIS ROUTER TABLE!!

Amazon is the only place that I found that had it listed for under $300. Plus the free shipping is great. It only took 7 days to receive it. Now I'm looking for a router to dedicate to the table. I know I'll buy it from Amazon I just can't make up my mind.

JOHN B
Just received my Bench Dog 40-031. There have been questions about mounting on left tilt table saws, so I was concerned because I have a Powermatic Artisans saw - years old but still works. The instructions say there IS an issue with left tilt cabinet saws - interference with moter and that must be the case because I had NO problems at all with my contractor style saw. In fact the whole install took less than 45 minutes including "play" time. I love this table so far,compact convenient, tough. Could be less bucks though.

Question about compatibility (Updated)
Update(5/19/04): The ProMax arrived yesterday and I installed it by myself by the end of the night. There are no interference issues with my Dewalt 746 tablesaw and Dewalt fixed router base that I plan to leave permanently attached to the ProMax router plate.

The cast iron extension is a significant improvement over the stock stamped steel wings that came with my Dewalt saw (bigger, flatter, smoother).

I haven't made any sawdust yet with this setup but so far it has been a tremendous value when you think about how much you actually get (fence, router plate, cast iron extension wing).
(END OF UPDATE)

Tim Malone wrote a review that said the ProMax was the perfect fit for his Dewalt 746 saw. I just talked with someone from BenchDog and they had some concerns that the ProMax would have interference problems because my DeWalt is a left tilting saw. Tim (or anyone for that matter) can you tell me if your Dewalt was a left or right tilt saw. I was not aware of Dewalt making the 746 in a right tilt version. If there is anyone out there that has installed the ProMax on a left tilter, please let me know.

Thanks in advance,
Bob

Initial Impressions, Installation
Here are my initial impressions on the Cast Iron Table through installation. I will update this post after I use it some.

The wing is boxed well and though there was a little damage to the box, the contents were in good shape. The first thing I noticed when beginning assembly is the screws and bolts were packed in some random order. I recommend dumping them all into a ziplock bag before starting. This will save you some time having not to disassemble or look for other bags. The wing is well coated with oil. I used simple green to remove the residue. After it was clean, I assembled it to the saw. Fit up was good and this wing is flat (more flat than my saw). The fence is quality and went together with no problems and the insert leveled with no issues.

Now for the reason I gave this product a 4 star rating. The wing is supplied with hooks to hold the fence when not in use. These hooks share the same hole as the attachment screws for the miter gage. The problem is that the holes were not tapped all the way through, they stopped about 1/8" shy. I have three options, to tap the holes myself, return the wing (now that it is fully assembled), or not use the hooks at all. The last option is not an option as far as I am concerned. I will speak with Bench Dog customer service tomorrow to see what they can do. Oh yeah, I almost forgot, they shorted me one lock washer as well.

Update 4/23/04, I moved this from a 4 star to a 5 star due to their customer service. I called and they sent me a tap to complete the threads. The were willing to replace the wing but I have done a lot of metal work in the past so finishing the hole was no problem. They were aware of the problem and were very appologetic. I used this on some cherry and boy is it nice. I would recomend this to anyone who has a space constrant in their shop.

Customer Service
First of all I would like to say that this is strictly a quality product. A perfect for for my Dewalt 746. Adjusting the router bit height could not be any easier due to no cabinet around the router. Due to my getting one of the first new type shipped I had to call customer service about a couple of issues. I just started up a shop and have had to call Powermatic, Dewalt, Bosch, Shop Fox, Delta, Kreg etc.about missing bolts, nuts, etc. and Bench Dog was by far the most knowlegeable, helpful and shipped the replacement items the fastest. I would not hesitate to buy anything this company manufacturers. ... Read more

Amazon.com Review

Instead of throwing away old, dull bits, give them a checkup with the Drill Doctor and extend their life. Although drill-bit sharpening systems often fail to live up to our expectations, we're here to bear witness for the truth of the Drill Doctor's claims: it really does sharpen old bits in just a couple of minutes. The 750SP (also known as the Professional) works on conventional, split-point, and masonry bits from 3/32 to 3/4 inches in size. If you don't plan on sharpening anything larger than 1/2-inch bits, we recommend getting the 500SP instead; it's basically the same machine, minus the cost of the 3/4-inch chuck that comes with this model. Both models--the 500SP and the Professional 750SP--allow you to choose between a 118- and 135-degree sharpening angle. Operation is fairly simple, but to make sure no one has trouble figuring it out, the Drill Doctor comes with a how-to video. Anyone who frequently wears down drill bits is going to appreciate the savings this handy machine can offer. Using sharp bits instead of dull ones also increases the life of your drill, because sharper bits require less work to make the same hole. We only wish we'd found the Drill Doctor sooner. --Brian Trinen ... Read more

Features

• Sharpens conventional point, split point, and masonry drill bit at 118- or 135-degree angles
• Two chucks accept 3/32- to 1/2-inch and 1/2- to 3/4-inch bit shafts
• Long-lasting Diamond wheel sharpens carbide, high-speed steel, standard, cobalt, and more
• Comes with how-to video

Reviews (33)

Drill Doctor DD750PK Precision Drill Bit Sharpene
There are many good things about this product. When I called tech support with a problem (chuck sticking), I got a human being with a knowledgable answer (loosen a few overtorqued screws) in a matter of minutes. On standard drill bits, it works very well.

However, I got it mostly to sharpen hex-base drill bits, as I use these drill bits with a quick-change chuck all the time. And I basically destroyed several bits (well, they were dull anyway) finding out that the chuck supplied with this unit simply can't get a proper grip on hex-base drill bits. They will be out of alignment, which means it won't work, at all. You just grind off random bits of your drill bit at random angles, resulting in a useless bit. Well, I _was_ able to sharpen a few of the bigger hex bits, but the 1/16", 1/8", and 3/16" bits were trashed.

So for my main use--sharpening hex-base bits--this fails pretty badly. If I'd known this, I wouldn't have gotten it. (Of course none of the marketing information or tech support information mentions this--if they did, they might lose some sales.) So I'll keep it, but quite disappointed. And no, tech support didn't have any suggestions for how to fix the problem.

So, if you want to sharpen small hex bits, give this a pass. If you don't use hex bits, it is a good deal. And the video they supply is excellent for teaching you how to use it.

Your mileage may vary.

The BEST Drill Sharpening System
Over the years I have collected hundreds of drill bits that served me well when new. But with each project I found myself looking for a sharp bit to complete the task. I needed a repeatable way to sharpen my drill bits. After extensive research and product reviews I purchased the Drill Doctor 750. It did EVERYTHING it promised. It sharpened both small and large bits, it removed all nicks and restored the cuting edge perfectly. The actual process is simple and quick. The video gives good instructions, but practice makes perfect, and I actually enjoyed sharpening all my old bits. I highly recommend the Drill Doctor. It delivers on its promise every time.

Pays for itself quickly
Glad I FINALLY bought one!
With the price of drill bits rising every day this baby will pay for itself quickly. Sharpens bit as good as or better than new. If you think you doing a good job sharpening bits on a bench grinder, you'll be suprised. Don't know how the hail I ever got along without one of these. Will never have to use a dull bit again. An absolute NECESSITY for anyone working with steel. I would suggest getting an extra wheel upon purchase because once you sharpen about 250 of your dead/dull bits after it arrives, you'll most likely need a new wheel.

The Good, the bad, and the great
I just received my Drill Doctor 750SPK and was surprised to find that it came with a carrying case which was listed by Amazon.com as an accessory. The first time I used the Drill Doctor it performed perfectly and I was inclined to sharpen even drills that I had previously considered sharp. For normal drill sharpening, I would rate it as 5-star. The only problem I had was with split tips. The drill holder does not slide smoothly in and out of the guide. It requires unnecessay force as far as I am concerned, however with extra effort I can sharpen split tips adequately. I will keep the unit since most of my sharpening is for standard tips. When and if I want to do many split tips, I will bore the guide out a little and and install a "pop-out" spring to move the tip back off the grinding wheel.

Incidently, one reviewer said that he received screwdriver tips instead of drills with his unit. I did not find that to be the case. I received the drills.

NO MORE DULL Excuses!!
This is product is everything good all have said about it. Order fulfill by Amazon - excellent! Unit well packed, handy carry case is superb.
Set up and use - I watched the video 1 & 1 1/2 times. Getting the drill set up properly is the whole equation - and is easy. I have sharpened both angle configurations, and split a few points just to see how easy it is to do. SNAP!
I didn't realize how bad a shape I was in until I cleaned up every bit I owned. I mostly work wood and don't demand a lot of twist drills here, but a few metal things came up and I realized I had a sour batch of drills. Problems solved. Everyone needs one of these....or maybe I keep it a secret and make a few $$ fixing up my neighbors tools. It would almost be like stealing. Maybe I'll do demo's and sell units. ... Read more

Features

• 2 Batteries
• Carry bag
• 18V
• Brute Tough
• 6 tools