Features

• 8,000/10,000 rpm
• Uses 1/2" and 3/4" spindle bits
• Powerful 3 hp, single-phase motor
• 25-by-18-inch solid cast-iron table
• 4" dust port

Reviews (1)

Great Shaper!!
I recently purchased the Jet JWS-25Cs and could not be more happy with the product, pleanty of power!! Setup was easy, no surprises. Fence system is solid. Comes with 1/2 and 1/4 router bit collets. Spindle changes are relatevely easy. Unfortunately you need to open the rear access door to make spindle changes, I wish they designed it to be done from the side access panel to avoid, in my case, having to move the machine away from the wall to open the rear door. I have heard some comments about router bits not working well in shapers because router bits are designed to spin faster. I can tell you that I tried several router bit and they work just fine at the 10,000 rpm setting. ... Read more

Amazon.com Review

Raised panels, here you come. And you'll never have to buy another piece ofmolding again. The Shopmaster SH100's powerful 9 amp ball bearing induction motorwill run 1/4-inch and 1/2-inch bits at 12,500 rpm through any stock you feed it. It comeswith a two-piece fence, and the halves are independently adjustable, so you'll get precisedepth of cut and ample support post-cut. The clear blade guard does double duty, keepingchips and dust away from your face and helping the dust chute pull out the waste. Weparticularly like the spindle control knob and its height indicator scale, which makeadjustments easier. The lock knob securely holds your settings, and the 3-3/4-inch insertopening will take even the beefiest bit. The 18-by-20-inch die-cast aluminum table offersgreat work support and has a slot opening for accessory holding devices. Finally, thepower switch has a removable lockout key, so little fingers won't be able to turn on theshaper when you're not there. --Kris Jensen-Van Heste ... Read more

Features

• 2-year limited warranty on machines, parts, and accessories
• 9-amp induction-type ball bearing motor for long lasting trouble free operation
• All purpose 12,500 rpm spindle speed handles any routing or shaping job including horizontal panel raising
• Die-cast aluminum 18- by 20-inch table provides ample work support; integral slot facilitates use of accessories
• Removable on-off switch prevents unauthorized use of machine

Reviews (9)

Delta SH100 Shopmaster Bench Top Router/Shaper
ASSEMBLY: Assembly was straightforwoard and took less than 30 minutes.

SETUP: Table alignment was acceptable out of the box.

PROs and CONs: I purchased this tool for use as a router table rather than a shaper, and it seems satisfactory for this purpose. However, the overhead blade guard did not fit in the hole provided in the table, nor did the replacement Delta sent me. The usable vertical spindle movement is only about 1-1/4 inches, limiting the use of longer bits. Finally, the small size of the adjustment knob makes adjusting the bit height more of a task than it need be.

You'll be sorry you spent the money
I used (not much) one of these for about a year in my home workshop. There is NOTHING good that I can say about it, except that the motor did actually run.

Notes:
- Lack of power, single speed, bogs down under load
- BAD BAD BAD Fence adjustment. You just can't get it set accurately. Can you say snipe?
- Poor height adjustment, but it can be done.
- Table top is sharp and rough, which makes feeding your material difficult and unsafe.
- No place for featherboards on the fence
- Single speed too fast for big bits, too slow for small ones
- The use of this machine will lead to a near terminal case of frustration.

For a hundred dollars more you can buy a Rousseau router plate, Bosch 1715EVS router, build your own table, Incra Ultra Lite jig (use as router fence - it's great with a slight modification - see review on amazon). I've used this setup without any trouble at all at least twice a week. Please, please, please don't waste your money on Delta's worthless router/shaper.

Know what you're getting into
I bought this device with a very specific single purpose in mind, and was able to make it work with a LOT of effort. I wanted to do tongue-and-groove on some long cedar boards for paneling, and after a lot of futzing was able to make acceptable joints on all my boards. It was cheaper than a good router and table would have been.
That having been said, this is neither a router table NOR a shaper, and combines the WORST of both. The fence adjustment stinks, ditto the height adjustment (see other reviews). The hole in the top won't accept wide bits, so I had to use a spacer board to get my planks to the right cutting height, which is why I had no problems with the sharp edges on the tabletop snagging my workpiece. The extension table accesory requires the removal of the fence and dust collection port. The single speed is too slow for small bits and too fast for big ones. This is not a very adaptable or flexible machine. Buy a router and table.

Minor faults
I bought this after I discovered a cheaply made table and add on router cost more. I've heard all kinds of complaints for adjusting the combo set-ups. I did not want to hassel with that. The Delta works real well. Table top is good. Fences are good quality but a little hard to adjust. I have only used 1/4" cutters (My local hardware does not have 1/2") and have trouble removing them. I'll order the 1/2" cutters. My main complaint is the depth adjustment. I had expected it to be more accurate. I'll have to work with it more and get used to it. Overall a very good machine for the money.

I do not know what the problem is?
I have been pleased overall with this shaper for the price. My major complaints are the fence has no t-track or fine adjustment as is,and why can't the manuf. give you a real wrench instead of the poor quality stamped wrenches. I already have cracked one, which Delta replaced. I use a real wrench now and want to change the fense some day.For now I add another face to it.
The height adj. will not be accurate if you lower it to final height but the manual says to raise it to final height and then is no problem with the lock down. Sometimes it pays to read it.
As far as height length of the bit,my unit will allow the spindle to extend beyond the top?
If you wax the top you will not have any marking, or spray a coat of clear poly on it. Woodworkers are in the habit of waxing and polishing metal tops all the time.
The collets self release, but 99% of the time I use 1/2" shanks. Do you want to use a 1/4' shank on a shaper unless you have no choice? I have no problem with the 1/4' sticking on the rare occasion that I have to use it. I avoid 1/4 shanks if at all possible. As with all self releasing collets, you have to continue to turn the nut to get to the self release feature. Over insertion on any collet can cause problems too. That is a universal problem. Also as mentioned, quality router bit can also make a huge difference.
I have no run out, the inserts line up, and there is good dust collection and I am not sucking dust into my router as most will when upside down. I can use it at job site too even though it is heavy, but that is a plus for stability and lack of vibration.
It is not a $1000 shaper, maybe others thought it would perform like one. If you want that type of performance spend the money.
I have milled almost a thousand feet with this unit and would buy it again. ... Read more

Amazon.com

The professional cabinetmaker either already has this shaper—-or wants it. The X5 series of tools exceed Delta's exacting standards for pro-grade instruments, producing the very best results. This powerful shaper has three horses under the hood running a poly V-belt, while on the surface are two rock-solid, flat and true cast-iron extension wings and our favorite feature, the micro-adjustable fence, arguably the best on the market. Accessing both spindle speeds is a quick, no-hassle task. The cutter guard is easy to work with, and the smoothly tapered start pin gives you a safe way to cut away from the fence with a combination of cutters and collars. An absolute powerhouse, it doesn't whine or snag no matter what you feed it. Making raised panels is like a day at the beach with this machine in your shop. Without a doubt, this is among the finest shapers we've seen.--Kris Jensen-Van Heste ... Read more

Features

• Five year limited warranty on machines, parts and accessories
• 3HP single phase motor with full voltage motor starter (GPE)
• Controls, motor, pulley, Poly V-belt drive
• Two 10" cast iron extension wings, micro adjustable fence and guard assembly
• 3/4" spindle, table inserts, starting pin, 2-speed spindle pulley and wrenches

Reviews (1)

good machine
I just set this machine up yesterday and I love it already. I have been in the cabinet business for years and this is the most easily adjustable fence I have ever used. This shaper is worth the price. ... Read more

Features

• Precision fine-tune adjustment is easily accomplished and locked into position with "quick-lock" handles
• Spindle assembly is mounted to table bottom
• Work piece hold-downs are fully adjustable
• Spindle is mounted in heavy-duty precision ball bearings
• Removable inserts make the use of any cutter safer via undercutting (raised panel cuts)

Reviews (3)

Almost a great product
As earlier stated by Alan, the spindle opening had a burr that had to be removed before stock could be shaped, especially with a power feeder. The wood fence attachments need more than two holes bored in them to be able to properly adjust them to all size shaper cutters. The documentation was not up to par. If you spend close to $2,500 for a machine, the documentation should be first rate. For example, I couldn't find any specifications that showed how much of an increment the adjustable fence moves with one revolution (1/32"), nor could I find that information on the height adjustment. Finally, I'm disappointed with the shaper plate. The largest plate has a lip that holds the next smaller plate, and there is no way to use that large plate with a 4" cutter, especially the larger cope and stick cutters. You wind up having to take the ring out completely, or fashion one of your own. Having said all of this, I would still buy this machine. If you have enough confidence to tackle the minor inconveniences mentioned in this and other reviews, I don't think you can find a more solid machine.

The pros and cons
First the cons: ... The fence is fastened to the table duringshipping and the paint was obviously wet when it was shipped as therewas a fair amount of dried paint on the table in the shape of the fence outline. The table also had a slight burr around the spindle opening that had to be removed before wood would slide easily across it. It takes 4 srews/nuts to hold the wooden fence to the metal part - they sent one. No hex key wrenches were included although you need several to adjust the fence. The manual content and orginizaion was so-so. Also, a miter guage would have been nice.

The Pros: once the above problems were corrected and the belt adjusted properly, the machine worked like a charm. The 5 hp motor muscles through cuts with ease and the dust collection works quite well. There is virtually no vibration and it runs more quiter than I'd expected. If you don't mind doing some of the finish work on the tool, it's a nice piece of equipment.

Industrial strength
I purchased this not on-line. It is a very good unit and has performed to every expectation I had. Just remember to get a power feed for most work and the fence is tricky to setup the first time.

However I like it much better than the other units because the quality of cut requires no finish sanding and this machine can cut all day long. ... Read more

Features

• Two-year limited warranty on machines, parts, and accessories
• 3-horsepower, 230-volt motor provides plenty of power
• Poly V-drive system transmits more efficient torque to the spindle
• Unitized design of motor, spindle, and height adjustment mechanism for more accuracy
• Micro-adjust fence makes set ups quick, esy, and precise

Reviews (1)

Consider others before you buy...
I purchased this tool at a special price during a sale. There was also a rebate on it at the time. So I bought...

The shaper is good quality and I've had no problems with it. Delta offers accessory spindles from .5 in. to 1.25" as well as a spindle to allow use of 1/2" router bits. They are overpriced...

The fence system is good quality but I don't care for the design. It looks cool... Delta has incorporated a system of hold-downs into the fence that look pretty but aren't terribly functional. I would prefer the simpler wood fence with the spring hold-downs. The micro-adjustment is nice.

Overall, 3 stars... The shaper works well and is a nice tool. The fence is not a good as it looks. In my opinion, there are better values to be had from other manufacturers. ... Read more

Product Description

We've taken our immensely popular shaper described above and made it even better! Now you can get it with a sliding table! Shaping long stiles and rails will be easier and more consistent with this production wood shop machine. ... Read more

Features

• All other specifications same as the G5912Z
• Cast Iron Miter Gauge with 60° angle capability in two directions
• Sliding Table: 35-1/2"W x 13-1/4"D
• Table Fence: 39-1/2" Extruded Aluminum with adjustable stop
• Table Travel: 21-7/8"

Features

• Covered by Freud's limited lifetime warranty
• Set consists of two insert cutter heads which accept carbide insert knives
• Eighteen different looks and the cost savings of resharpenable knives
• Thick micrograin carbide tips
• Kickback reducing design

Reviews (1)

Shaper cutter 1 1/4" arbor
I purchased this set some years ago when it was a relitively new design and have never been dissapointed. for the money you cant beat the value. it has allowed me to seperate my work from the work of others by being able to offer a very wide variety of profiles. all cuts are superior to router bits and most other shaper cutters. at the time the set came with shims for creating the correct stub tenon thickness for the different profiles available and pinpoint accuracy is paramount with this set. It also allows a "full-cut" to be taken, this is handy when working with poorly joined edges as you can offset the fence to join on the shaper. obviously freud engineers realy did their homework on this one. The quality of cut rivals the work produced by many of the so called dedicated door manufacturers. if you are serious about making high quality doors then this set is worth the investment. setup can be a little tedious at first but after practice youll have perfection. good luck. ... Read more

Product Description

Built with plenty of muscle to take on most shaping challenges, our mid-sized, 1 1/2HP Model G1035 Shaper offers the perfect low-priced alternative for the serious hobbyist or small-shop owner. The G1035 offers precision wheel adjustment, two spindle speeds, a finely-milled cast iron table, interchangeable spindles and sealed ball bearing movement â all for less than the price of a router and router table! ... Read more

Features

• 2 interchangeable spindles: 1/2" and 3/4"
• 3" spindle travel
• Heavy-duty 1-1/2 H.P., 110V/220V motor
• Reversing switch
• Two spindle speeds: 7,000 and 10,000 R.P.M.

Features

• Fits Porter Cable router tables 695, 696, 697, and 698
• All steel construction
• Stand height 24-1/4", Table height 38-1/2"

Reviews (1)

Good Stand but No Feet!
This stand is a perfect fit for the Porter Cable 691RS Ultimate Router Workshop, with which I bought it. Assembly was easy, and the stand sturdy as can be. The only problem (and it's considerable) is that it shipped without the rubber bushings (feet) that the directions said were included. So it slides. If the manufacturer comes through with the feet, it'll be a five for value and performance. ... Read more

Product Description

Build the entryway of your dreams using our 6-piece stile and rail set. Set includes 5 cutters and one spacer. We also have 1/2" and 5.5mm cutters and spacers available for 3/4" bore only. Please order panel cutters separately. (See pages 384-385.) ... Read more

Features

• Cutter Dia.: 3-1/8"
• Cutting Length: 1-3/4"
• Cutting Width: 5/8"

Product Description

,Motor: 3/4 HP, 110V, 60 HZ ,Spindle Size: 1/2" ,Collet Size: 1/4" ,Maximum Cutter Height: 1 9/16" ,Maximum Cutter Height Adjustment: 19/32" ,Spindle Speed: 9500 RPM ,Table Size: 11 13/16 x 9 13/16" ,Fence: Independently adjustable ,Dust Port: 2 1/2" ,Accepts 1/4" router bits ,Weight: 42 lbs. ... Read more

Features

• Accepts 1/4" router bits
• Collet Size: 1/4"
• Motor: 3/4 HP, 110V, 60 Hz
• Spindle Size: 1/2"
• Spindle Speed: 9,500 RPM

Reviews (1)

measurements
I did not find the width measurements on this item,
how wide a board will it cut?
2 inches 3 inches or wider?
Also what is a collet? ... Read more

Product Description

Create your own custom flooring materials from standard dimensional materials with these carbide cutters. Designed for use with 5/8" and 3/4" lumber, these cutters are great for designing new floors or for creating replacement planks for repair and renovation. For use on 3/4" spindles. Tongue and groove are below center, so you can resand and finish a number of times. ... Read more

Features

• C2305/C2306 Cutter Dia.: 2-5/8"
• C2305/C2306 Cutting Length: 1"
• C2305/C2306 Cutting Width: 5/8"/1/2"

Features

• Cutter Dia.: 4-5/8"
• Cutting Length: 5/8"
• Cutting Width: 1-1/2"

Product Description

This handy little Flexcut draw knife was developed for fan carving but works great for skinning bark and rounding off corners. It is especially useful for peeling bark from small walking sticks and canes. Fits nicely into your tool roll. 3" cutting edge, 12" overall length. ... Read more

Features

• Thick micrograin carbide tips
• Kickback reducing design
• Covered by Freud's limited lifetime warranty

Features

• Thick micrograin carbide tips
• Kickback reducing design
• Covered by Freud's limited lifetime warranty

Product Description

Grizzly 3/4" Bore Shaper Cutters feature top-quality C-2 carbide--the best available for wood cutting applications. Shaped and sharpened with diamond wheels as fine as 600 grit, these outstanding cutters are constructed with a high-tensile, silver-based brazing, which offers the utmost in strength and durability. Can be used on woods, wood composites, plywood and some plastics at 5,000 to 10,000 RPM. An excellent selection. ... Read more

Features

• Cutter Dia.: 2-5/8"
• Cutting Length: 15/16"

Product Description

Grizzly 3/4" Bore Shaper Cutters feature top-quality C-2 carbide--the best available for wood cutting applications. Shaped and sharpened with diamond wheels as fine as 600 grit, these outstanding cutters are constructed with a high-tensile, silver-based brazing, which offers the utmost in strength and durability. Can be used on woods, wood composites, plywood and some plastics at 5,000 to 10,000 RPM. An excellent selection. ... Read more

Features

• Cutter Dia.: 2-5/8"
• Cutting Length: 3/4"

Features

• Thick micrograin carbide tips
• Kickback reducing design
• Covered by Freud's limited lifetime warranty