Amazon.com Review

Raised panels, here you come. And you'll never have to buy another piece ofmolding again. The Shopmaster SH100's powerful 9 amp ball bearing induction motorwill run 1/4-inch and 1/2-inch bits at 12,500 rpm through any stock you feed it. It comeswith a two-piece fence, and the halves are independently adjustable, so you'll get precisedepth of cut and ample support post-cut. The clear blade guard does double duty, keepingchips and dust away from your face and helping the dust chute pull out the waste. Weparticularly like the spindle control knob and its height indicator scale, which makeadjustments easier. The lock knob securely holds your settings, and the 3-3/4-inch insertopening will take even the beefiest bit. The 18-by-20-inch die-cast aluminum table offersgreat work support and has a slot opening for accessory holding devices. Finally, thepower switch has a removable lockout key, so little fingers won't be able to turn on theshaper when you're not there. --Kris Jensen-Van Heste ... Read more

Features

• 2-year limited warranty on machines, parts, and accessories
• 9-amp induction-type ball bearing motor for long lasting trouble free operation
• All purpose 12,500 rpm spindle speed handles any routing or shaping job including horizontal panel raising
• Die-cast aluminum 18- by 20-inch table provides ample work support; integral slot facilitates use of accessories
• Removable on-off switch prevents unauthorized use of machine

Reviews (9)

Delta SH100 Shopmaster Bench Top Router/Shaper
ASSEMBLY: Assembly was straightforwoard and took less than 30 minutes.

SETUP: Table alignment was acceptable out of the box.

PROs and CONs: I purchased this tool for use as a router table rather than a shaper, and it seems satisfactory for this purpose. However, the overhead blade guard did not fit in the hole provided in the table, nor did the replacement Delta sent me. The usable vertical spindle movement is only about 1-1/4 inches, limiting the use of longer bits. Finally, the small size of the adjustment knob makes adjusting the bit height more of a task than it need be.

You'll be sorry you spent the money
I used (not much) one of these for about a year in my home workshop. There is NOTHING good that I can say about it, except that the motor did actually run.

Notes:
- Lack of power, single speed, bogs down under load
- BAD BAD BAD Fence adjustment. You just can't get it set accurately. Can you say snipe?
- Poor height adjustment, but it can be done.
- Table top is sharp and rough, which makes feeding your material difficult and unsafe.
- No place for featherboards on the fence
- Single speed too fast for big bits, too slow for small ones
- The use of this machine will lead to a near terminal case of frustration.

For a hundred dollars more you can buy a Rousseau router plate, Bosch 1715EVS router, build your own table, Incra Ultra Lite jig (use as router fence - it's great with a slight modification - see review on amazon). I've used this setup without any trouble at all at least twice a week. Please, please, please don't waste your money on Delta's worthless router/shaper.

Know what you're getting into
I bought this device with a very specific single purpose in mind, and was able to make it work with a LOT of effort. I wanted to do tongue-and-groove on some long cedar boards for paneling, and after a lot of futzing was able to make acceptable joints on all my boards. It was cheaper than a good router and table would have been.
That having been said, this is neither a router table NOR a shaper, and combines the WORST of both. The fence adjustment stinks, ditto the height adjustment (see other reviews). The hole in the top won't accept wide bits, so I had to use a spacer board to get my planks to the right cutting height, which is why I had no problems with the sharp edges on the tabletop snagging my workpiece. The extension table accesory requires the removal of the fence and dust collection port. The single speed is too slow for small bits and too fast for big ones. This is not a very adaptable or flexible machine. Buy a router and table.

Minor faults
I bought this after I discovered a cheaply made table and add on router cost more. I've heard all kinds of complaints for adjusting the combo set-ups. I did not want to hassel with that. The Delta works real well. Table top is good. Fences are good quality but a little hard to adjust. I have only used 1/4" cutters (My local hardware does not have 1/2") and have trouble removing them. I'll order the 1/2" cutters. My main complaint is the depth adjustment. I had expected it to be more accurate. I'll have to work with it more and get used to it. Overall a very good machine for the money.

I do not know what the problem is?
I have been pleased overall with this shaper for the price. My major complaints are the fence has no t-track or fine adjustment as is,and why can't the manuf. give you a real wrench instead of the poor quality stamped wrenches. I already have cracked one, which Delta replaced. I use a real wrench now and want to change the fense some day.For now I add another face to it.
The height adj. will not be accurate if you lower it to final height but the manual says to raise it to final height and then is no problem with the lock down. Sometimes it pays to read it.
As far as height length of the bit,my unit will allow the spindle to extend beyond the top?
If you wax the top you will not have any marking, or spray a coat of clear poly on it. Woodworkers are in the habit of waxing and polishing metal tops all the time.
The collets self release, but 99% of the time I use 1/2" shanks. Do you want to use a 1/4' shank on a shaper unless you have no choice? I have no problem with the 1/4' sticking on the rare occasion that I have to use it. I avoid 1/4 shanks if at all possible. As with all self releasing collets, you have to continue to turn the nut to get to the self release feature. Over insertion on any collet can cause problems too. That is a universal problem. Also as mentioned, quality router bit can also make a huge difference.
I have no run out, the inserts line up, and there is good dust collection and I am not sucking dust into my router as most will when upside down. I can use it at job site too even though it is heavy, but that is a plus for stability and lack of vibration.
It is not a $1000 shaper, maybe others thought it would perform like one. If you want that type of performance spend the money.
I have milled almost a thousand feet with this unit and would buy it again. ... Read more

Features

• 8,000/10,000 rpm
• Uses 1/2" and 3/4" spindle bits
• Powerful 3 hp, single-phase motor
• 25-by-18-inch solid cast-iron table
• 4" dust port

Reviews (1)

Great Shaper!!
I recently purchased the Jet JWS-25Cs and could not be more happy with the product, pleanty of power!! Setup was easy, no surprises. Fence system is solid. Comes with 1/2 and 1/4 router bit collets. Spindle changes are relatevely easy. Unfortunately you need to open the rear access door to make spindle changes, I wish they designed it to be done from the side access panel to avoid, in my case, having to move the machine away from the wall to open the rear door. I have heard some comments about router bits not working well in shapers because router bits are designed to spin faster. I can tell you that I tried several router bit and they work just fine at the 10,000 rpm setting. ... Read more

Product Description

Built with plenty of muscle to take on most shaping challenges, our mid-sized, 1 1/2HP Model G1035 Shaper offers the perfect low-priced alternative for the serious hobbyist or small-shop owner. The G1035 offers precision wheel adjustment, two spindle speeds, a finely-milled cast iron table, interchangeable spindles and sealed ball bearing movement â all for less than the price of a router and router table! ... Read more

Features

• 2 interchangeable spindles: 1/2" and 3/4"
• 3" spindle travel
• Heavy-duty 1-1/2 H.P., 110V/220V motor
• Reversing switch
• Two spindle speeds: 7,000 and 10,000 R.P.M.

Features

• 1-year warranty
• Woodworking shaper with 3HP 1ph 230V motor
• Fully adjustable work piece hold-downs enable precision accuracy
• Reversible two speed spindle: 7,500 and 10,000 RPM
• 4-inch dust collection port with a built into the fence

Features

• Precision fine-tune adjustment is easily accomplished and locked into position with "quick-lock" handles
• Spindle assembly is mounted to table bottom
• Work piece hold-downs are fully adjustable
• Spindle is mounted in heavy-duty precision ball bearings
• Removable inserts make the use of any cutter safer via undercutting (raised panel cuts)

Reviews (3)

Almost a great product
As earlier stated by Alan, the spindle opening had a burr that had to be removed before stock could be shaped, especially with a power feeder. The wood fence attachments need more than two holes bored in them to be able to properly adjust them to all size shaper cutters. The documentation was not up to par. If you spend close to $2,500 for a machine, the documentation should be first rate. For example, I couldn't find any specifications that showed how much of an increment the adjustable fence moves with one revolution (1/32"), nor could I find that information on the height adjustment. Finally, I'm disappointed with the shaper plate. The largest plate has a lip that holds the next smaller plate, and there is no way to use that large plate with a 4" cutter, especially the larger cope and stick cutters. You wind up having to take the ring out completely, or fashion one of your own. Having said all of this, I would still buy this machine. If you have enough confidence to tackle the minor inconveniences mentioned in this and other reviews, I don't think you can find a more solid machine.

The pros and cons
First the cons: ... The fence is fastened to the table duringshipping and the paint was obviously wet when it was shipped as therewas a fair amount of dried paint on the table in the shape of the fence outline. The table also had a slight burr around the spindle opening that had to be removed before wood would slide easily across it. It takes 4 srews/nuts to hold the wooden fence to the metal part - they sent one. No hex key wrenches were included although you need several to adjust the fence. The manual content and orginizaion was so-so. Also, a miter guage would have been nice.

The Pros: once the above problems were corrected and the belt adjusted properly, the machine worked like a charm. The 5 hp motor muscles through cuts with ease and the dust collection works quite well. There is virtually no vibration and it runs more quiter than I'd expected. If you don't mind doing some of the finish work on the tool, it's a nice piece of equipment.

Industrial strength
I purchased this not on-line. It is a very good unit and has performed to every expectation I had. Just remember to get a power feed for most work and the fence is tricky to setup the first time.

However I like it much better than the other units because the quality of cut requires no finish sanding and this machine can cut all day long. ... Read more

Features

• Fully adjustable workpiece hold-downs on table for keeping stock in position
• Extra large, heavy-duty cast iron table for stability
• Fully enclosed cabinet stand for longer motor life
• Handwheel and spindle lock for safe, accurate spindle height adjustments
• Two reversible spindle speeds for versatility

Features

• Two-year limited warranty on machines, parts, and accessories
• 3-horsepower, 230-volt motor provides plenty of power
• Poly V-drive system transmits more efficient torque to the spindle
• Unitized design of motor, spindle, and height adjustment mechanism for more accuracy
• Micro-adjust fence makes set ups quick, esy, and precise

Reviews (1)

Consider others before you buy...
I purchased this tool at a special price during a sale. There was also a rebate on it at the time. So I bought...

The shaper is good quality and I've had no problems with it. Delta offers accessory spindles from .5 in. to 1.25" as well as a spindle to allow use of 1/2" router bits. They are overpriced...

The fence system is good quality but I don't care for the design. It looks cool... Delta has incorporated a system of hold-downs into the fence that look pretty but aren't terribly functional. I would prefer the simpler wood fence with the spring hold-downs. The micro-adjustment is nice.

Overall, 3 stars... The shaper works well and is a nice tool. The fence is not a good as it looks. In my opinion, there are better values to be had from other manufacturers. ... Read more

Product Description

We've taken our immensely popular shaper described above and made it even better! Now you can get it with a sliding table! Shaping long stiles and rails will be easier and more consistent with this production wood shop machine. ... Read more

Features

• All other specifications same as the G5912Z
• Cast Iron Miter Gauge with 60° angle capability in two directions
• Sliding Table: 35-1/2"W x 13-1/4"D
• Table Fence: 39-1/2" Extruded Aluminum with adjustable stop
• Table Travel: 21-7/8"

Product Description

,Motor: 3/4 HP, 110V, 60 HZ ,Spindle Size: 1/2" ,Collet Size: 1/4" ,Maximum Cutter Height: 1 9/16" ,Maximum Cutter Height Adjustment: 19/32" ,Spindle Speed: 9500 RPM ,Table Size: 11 13/16 x 9 13/16" ,Fence: Independently adjustable ,Dust Port: 2 1/2" ,Accepts 1/4" router bits ,Weight: 42 lbs. ... Read more

Features

• Accepts 1/4" router bits
• Collet Size: 1/4"
• Motor: 3/4 HP, 110V, 60 Hz
• Spindle Size: 1/2"
• Spindle Speed: 9,500 RPM

Reviews (1)

measurements
I did not find the width measurements on this item,
how wide a board will it cut?
2 inches 3 inches or wider?
Also what is a collet? ... Read more

Product Description

STANDARD EQUIPMENT INCLUDES: Motor, reversing switch, magnetic power switch, miter gauge and fence with hold-down springs. ... Read more

Features

• 2 spindle speeds: 7,000 and 10,000 R.P.M.
• 3 H.P., single phase, 220V motor with reversing switch
• 3 interchangeable spindles: 1/2", 3/4" and 1"
• Spindle travel is 3"
• Table with standard wing attached measures 30-1/2" x 28-1/4"

Features

• Accomodates up to 6-1/4" cutter.
• Two reversing spindle speeds of 7,000 and 10,000 RPM.
• Independently adjustable fence wings.
• Large 30" x 28" precision ground table.
• Optional sliding table available.

Features

• Accomodates up to 6-1/4" cutter.
• Two reversing spindle speeds of 7,000 and 10,000 RPM.
• Independently adjustable fence wings.
• Large 30" x 28" precision ground table.
• Optional sliding table available.

Features

• Two-year limited warranty on machines, parts, and accessories
• 5-horsepower, 200/230/460-volt motor provides plenty of power
• Poly V-drive system transmits more efficient torque to the spindle
• Unitized design of motor, spindle, and height adjustment mechanism for more accuracy
• Micro-adjust fence makes set ups quick, esy, and precise

Product Description

Time and again we've had customers looking to permanently mount a router in a router table for under $300. Our new 3/4 HP Shaper is the perfect solution you get the precision of a shaper at a price that won't ruin your budget. The spindle accepts 1/2" shaper cutters. The fence assembly is easily removable and starting pins are included for freehand shaping. ... Read more

Product Description

,Spindle sizes: 3/4", 1 and 1 1/4" x 7 1/2" ,Spindle travel: 3 1/4", Spindle capacity: 5" (1 1/4" spindle) ,Table counterbore: 7" x 5/8" deep ,Maximum cutter diameter: 5 7/8" ,Spindle speeds: 3600, 5100, 8000 and 10,000 RPM ,Table size: 35 1/2"W x 28"D ,Overall dimensions: 28"D x 35 1/2"W x 42"H ,Heavy-duty, precision-ground cast iron table and fence assembly ,One-piece cabinet style stand ,Epoxy paint ,Independent, micro-adjustable fence with 4" dust port ,Shielded and permanently lubricated ball bearings ,5 HP, totally enclosed fan cooled, 220V, single-phase, 14 AMP motor ,Approximate shipping weight: 700 lbs. Includes: ,2 wood fence pieces ,3 spindles with 8 spaces and 2 nuts ,1 cast iron miter gauge ,4 hold down assemblies ,3 table inserts: 7" O.D. x 3 1/2" I.D., 3 1/2" O.D. x 3" I.D. and 3" O.D. x 2" I.D. ,Assorted wrenches. ... Read more

Features

• 3 spindles with 8 spacers and 2 nuts
• 5 H.P. totally enclosed fan cooled, 220V, single phase, 14 Amp motor
• Spindle capacity: 5" (1-1/4" spindle)
• Spindle sizes: 3/4", 1 and 1-1/4" x 7-1/2"
• Spindle speeds: 3600, 5100, 8000 and 10000 RPM

Product Description

SHAPER 7 1/2HP 3 PHASE ... Read more

Features

• 7-1/2 HP, 3 phase motor
• Heavy-duty, precision-ground cast iron table and fence assembly
• One-piece cabinet style stand
• Spindle sizes: 3/4", 1, and 1-1/4"
• Table size: 35-1/2" W x 28" D

Product Description

If you need moulding profiles in hardwoods that you can't find at your local millwork supplier, we think you'll find our new 5 HP Tilting Spindle Shaper worthy of your consideration. Built to withstand the rigors of industrial production, this impressive shaper will literally cut more profiles than you can shake a stick at. The unique tilting spindle will add even more variety and utility to your shaping operations and the conveniently located controls and adjustments make it a safe and easy machine to use and enjoy. ... Read more

Features

• 7-1/2 HP, 3 phase motor
• Maximum cutter diameter: 5-7/8"
• Spindle sizes: 3/4", 1", and 1-1/4"
• Table size: 28" x 35-1/2"

Product Description

Make production routing and shaping a breeze with this Overarm High Speed Router. Simply attach a template to the bottom of your workpiece and feed against the table- mounted pin. Overhead cutting lets you see your work. Hydraulic head and foot control speeds up your work even more. Includes clamp-on fence for in-line routing and massive tilting cast iron table for greater versatility. FEATURES: Fence or pin routing, Foot control for spindle movement, Head assembly travels on dovetail ways SPECIFICATIONS: Floor model (stand included), Table size: 24" W x 18" D, Overall height: 74", Overall width: 24" (no fence); 33 1/2" (w/ fence), Overall depth: 35", Motor: 3 HP, single-phase, 220V, TEFC, 15 amps, 3580 RPM, Shielded and permanently lubricated ball bearings, Power transfer: single flat belt, Spindle RPM: 20,000, Spindle stroke: 3 5/8", Head stroke: 5 3/4", Max. distance, spindle to table: 9 1/2", Swing: 19 1/2", Table tilt: 45 DEG, Approximate shipping weight: 650 lbs. ACCESSORIES INCLUDE: Tool box, Hex key wrench set, Grease gun, 1/2" collet, 1/4" collet, 36mm wrench â open, 26/23mm wrench, 13/11mm wrench, 19/17mm wrench, 3/8" plunge router bit with 1/2" ... Read more

Features

• Head stroke: 5-3/4"
• Motor: 3 H.P., single phase, 220V, TEFC
• Spindle RPM: 20,000
• Spindle stroke: 3-5/8"
• Table size: 24" W x 18" D

Product Description

If you prefer the tilting spindle option, yes it too can be had with the sliding table! Now, even the most complicated profiles can be done quickly, consistently and safely. ... Read more

Features

• All other specifications same as the G5913Z
• Cast Iron Miter Gauge with 60° angle capability in two directions
• Sliding Table: 35-1/2"W x 13-1/4" D
• Table Fence: 39-1/2" Extruded Aluminum with adjustable stop
• Table Travel: 21-7/8"

Reviews (1)

Poor quality - terrible customer service.
The machine arrived missing a leg. It was badly scuffed on the sides, the face plate and control arm.

The permanent metal plate incorrectly described this 5 HP single phase shaper as a 7.5 HP three phase machine. I'm trying to imagine how I can explain this to a buyer when trying to unload this.

Grizzly didn't seem surprised by these and other problems. They said they were unable to send a replacement leg because they did not have one and that perhaps I could find a metal fabricator to make and weld a replacement.

To make matters worse, it took hours just to report each problem and days for each response. Several other items were either missing or defective.

After Grizzly sent a tiny can of green paint and some of the missing and defective parts, I discovered that the motor spun backwards - a problem that again took hours to report on Grizzly's TOLL line and days for technician to tell me to rewire the motor. I suppose this would not be a problem if you're an electrician.

Whoever slapped this machine together had to be drunk or on drugs. Unfortunately, dealing with Grizzly customer service is even worse than the problems with their machines.

Amazon should not allow this poor excuse for a company on their site. This company obviously lacks in the quality control and customer service areas.

I have a workshop of top of the line Powermatic tools and, now, this piece of garbage. I have never experienced any problems with my many other machines and was amazed at how many things could be wrong with just one, brand new, Grizzly machine.

What a waste of time and money. I only wish I could give then less than one star - they do not deserve to be in business and they certainly don't deserve anyone's hard earned dollars. ... Read more

Product Description

Production Shops â your prayers have been answered! This 3 sided, heavy-duty shaper will pay for itself quickly in cabinet and production shops that normally require several shapers or time consuming cutter changes. The combinations of cutters and set-ups you can utilize on this machine are endless. A GREAT INVESTMENT! ... Read more

Features

• 3 micro adjustable fences
• Motor size: 3 H.P., TEFC Single Phase, 220V (Includes 3 motors)
• Spindle size: 1-1/4" (3/4" spindle available as an option)
• Spindle speeds (2): 7,000 and 10,000 RPM
• Working size of table: 15" x 32" (each side)