Features

• 19-3/4" cast aluminum base is 2X more rigid than a standard 10" base and folding tables
• One-year warranty through the Dewalt factory or an authorized service center
• Three knife cutter-head delivers 30% longer knife life and makes knife change faster and easier
• Two speed gear box allows users to change feed speed to optimizing cuts per inch at 96 or 179 CPI
• Fan-assisted chip ejection vacuums chips off of the cutter-head and exhausts them out of the machine

Features

• Exclusive 3 - speed all metal transmission
• DC390 cuts 2X4's at 45 degrees in a single pass
• One-year warranty through the Dewalt factory or an authorized service center
• DC385 with keyless blade clamp for quick blade changes
• DC988 drill/driver/hammerdrill has 500 in.-lbs. of maximum torque

Features

• 1/2" metal ratcheting chuck with carbide jaws helps to prevent bits from slipping
• DEWALT built high torque motor delivers 450 in-lbs of maximum torque
• One-year warranty through the Dewalt factory or an authorized service center
• XRP™ extended run-time batteries provide long run-time & battery life
• Patented 3-speed transmission features a max 3rd speed at 1,800 rpm

Features

• On-board hose, cord and accessory storage provides convenient transport and storage
• Runs off of 12-18V DEWALT battery packs or 120V AC
• Gore TM wet/dry filter traps 99.7% of drywall dust
• Wet/dry filter eliminates changeovers
• Heavy-duty rubber hose provides durability and flexibility

Features

• Factory reconditioned to perform like new! Limit 1 per order.
• Extra large dust bag
• Variable speed
• 7 amps

Reviews (2)

Best In Its Class
Plenty of power- doesn't bog down. Long lived ....... in shops I've worked in PC was the sander of choice.Belt tracks very well. The variable speed is handy and is a separate wheel control as it should be. At this price and the full warranty it's a no brainer. You could pay more and get a lot less sander.

Need to remove alot of stock? This sander is the best.
After trying several belt sanders on the market, I was extremely happy to come across this one. For starters, it never bogs down. No matter how much pressure is put on the platen or how long it runs, the motor never bogs. That was the main problem with other belt sanders I have used.

The sander also has some heft to it. It is not a light weight machine. This is good because it doesn't need a lot of extra force to remove a lot of stock, and the weight helps to keep it on track. If weight is a concern for you, you need to look elsewhere. Although the "elsewhere" sanders won't work as well!

This sander is tough. I was sanding a faceframe one day when my partner accidentally unplugged the machine. I set the machine down (this part is embarrassing) forgetting to turn the trigger off. When I plugged it back in, it pulled itself across the bench and onto the floor before I realized what was happening. It bounced a couple of times and continued across the floor before pulling the plug from the outlet. It purrs like a lion to this day. There has been other times when it has been dropped or stepped on and has never had any problems.

The only drawback, and the reason I gave it only 4 stars, is the dust bag. It gets in the way sometimes when working on other than horizontal surfaces. It can be swung around, though, to the left or right out of the way. Also, the dust bag forms a rub hole, right at the top where the aluminum tube ends inside the bag. I've sealed it with clear silicone which works fine. ... Read more

Features

• Hammer-Drill provides up to 495 in.-lbs. of torque and features an all-metal ratcheting chuck with carbide jaws for the highest grip torque on bits
• Hatchet with 6 position pivoting handle and an orbital action selector for aggressive wood cutting or straight reciprocating action for metal and plastics
• Circular saw cuts up to 145 2x4's on one charge for optimal productivity
• Reversible battery for adjusting balance and for getting into tight spaces

Features

• Head and handle swivel 360 degrees for easy drilling in tough spots
• Factory reconditioned to perform like new
• Designed for drilling between joist, studs, in tight corners, or in close quarters
• 0-355 rpm on low, 0-750 rpm on high, and 0-500 rpm with right-angle drive removed
• Trigger speed control for precise applications

Reviews (2)

wrong drill
I ordered the 3107-8 because it has two variable speed settings- 0-355 and 0-750. The carrying case said model 3107-8 but inside was a model 1107-1 which is 0-500 RPM only. Very disappointed.

Milwaukee 1/2" Right angle Drill
An elcellent drill to be used in those tight corners and spaces where any other drill & bit will no go. Right angle head rotates through 360 degress to aid in those tight spaces. With the ability to drill stright as well this "specialized" tool is not. Typical Milwaukee construction. Just finished a 3500 sq.ft. home wiring job. Worth every penny and then some for timely completion especially with owner changing partitions nearly daily.

Top recommendation. ... Read more

Features

• Drives 1-inch to 2-1/2-inch, 15 gauge DA type finish nails
• Adjustable exhaust port and depth-of-drive for maximum comfort and control
• Internal piston-catch ensures full driver blade stroke every time
• In-line glass filled magazine for left or right hand acc

Features

• Consistent power on every shot with internal piston catch mechanism
• Uses 22° 2" to 3-1/2" x .113" to .148" plastic collated round-head framing nails
• Nail lockout mechanism alerts operator to reload tool
• Tool-free adjustable exhaust
• Removable non-marring nose tip with on tool storage

Reviews (1)

Save some coin with a Porter Cable refurb!
My wife and I had the ambitious plan of finishing our basement. Since neither of us had any experience with home construction or woodworking, we decided that in order to do this right, we needed the right tools.

Considering the amount of framing we needed to do, a framing nailer was going to be a valuable tool. Being an important part of the process, I was concerned that a reconditioned tool might not be a good buy. I reviewed the details and as far as Porter Cable is concerned, a PC reconditioned tool has the same factory warranty as one fresh from the factory. Previous good experiences with PC tools helped me make the decision to get the FR350AR.

The nailer arrived in a large black plastic case. It came with a manual and a small bottle of machine oil. An inspection of the tool showed a little surface wear, probably from being put down on concrete or other abrasive surfaces, but PC molded sacrificial ridges on the tool body that take most of the abuse. The magazine mechanism was in good shape. It looked like the touched up some of the paint where it might have been chipped. All in all it was in excellent condition.

Saturday finally came and I was able to give the FR350AR a workout. I hooked it up to my PC pancake compressor that comes with the extremely popular brad/finish nailer kit, dialed in an initial pressure of 100 psi and hooked it up to the tool. There was a small hiss as the tool pressurized and was ready to go. I put on my safety gear and grabbed a stick of 3" ring plastic collated nails that I picked up from the neighborhood Lowe's. Nails are inserted from the rear of the magazine and pushed towards the front. You then grab the follower and pull it towards the back of the magazine and while still holding it, let it pull itself forward, pushing the nails into the firing mechanism.

While using the plastic tip, I pushed the tip against the 2x4 up on the ceiling joints and pulled the trigger. I heard a 'pop' with a little recoil and a nail was sunk 1/8" into the 2x4. The next test came when I started installing the studs. I removed the plastic tip to expose the spiked safety foot and put the plastic tip into the holder in the magazine. With the stud all centered, I placed the tip at a 45 degree angle and inch from the base of the stud and pulled the trigger. I nail shot into the stud and down into the base plate. It was left sticking out of the wood about 3/8 of an inch, enough to get at in case I needed to remove it. Excellent! The PC FR350AR will stop firing when you are down to four nails left in the magazine so you realize you need a refill. Insert more nails, readjust the follower and you were off and running again.

The pancake compressor seemed to do a good job holding up against the work I was doing with the nailer. I had it outside with a long hose run into the basement, so I couldn't hear it running. I didn't get any complaints from my neighbors so it must not have been running very often.

I only have two complaints with this nailer:

1) Although the tool is pretty balanced in my hand, the grip isn't spongy enough for my palm. The area between my thumb and forefinger was sore after all the nailing was done.

2) The plastic collation bits come shooting out of the nailer (from where exactly, I am not sure) and landed all around. I did find many bits in my hair afterwards so watch out for them.

Overall, I am extremely pleased with how well this reconditioned framing nailer has worked so far. I have plenty more work for it, so I will post an update another time for some long-term observations. ... Read more

Features

• Shaft lock for easy blade change
• Factory reconditioned to perform like new! Limit 1 per order.
• 13 amp motor
• Dual position depth adj. knob
• Bevels up to 45 feet left/ miters 0-47 left and up to 52 right

Reviews (2)

Makita 10" Dual Compound Slide Saw
Nothing less than what you'd expect in quality and performance in a Makita product. Well made and easy to use. The one design flaw is in the short fence which makes it difficult to cut large or tall molding. Reconditioned tools from Makita are a bargain, coming with a factory warranty - hard to loose.

Great Job Saw
I have Owned My saw for over 10 Years & being a carpenter by trade it has done a terrific job & still is going strong ... Read more

Features

• Adjustable footplate
• Variable speed
• Clic blade change system
• High efficiency 5 amp motor

Reviews (1)

Best Jig Saw on the Market!
I kid you not, this thing is AWESOME!!! I bought it to cut some curves in 7/8" Black Walnut and it cuts it like warm butter with a hot knife! I mean to tell you, this saw is great! ... Read more

Features

• One-year warranty through the Dewalt factory or an authorized service center
• Factory reconditioned to perform like new! Limit 1 per order.
• Features a 13.0 amp high-torque motor
• Telescoping fence delivers 24-1/2 inch rip capacity
• Limit one per order

Features

• User can engage contact trip lock-off and prevent accidental dis-charge of fastener.
• Provides increased durability over current cordless nailers and provides easy access for troubleshooting and service on the job-site or by a service technician.
• Works as fast as you do with consistent nail penetration into both soft and hard joints.
• Sequential operating mode allows for precision placement and the bump operating mode provides the user with production speed.
• Depths can be easily referenced utilizing numbered dial and user does not sacrifice performance when changing depths in hard wood joints.

Features

• Powerful 15 Amp, 3-1/2 max hp EVS Milwaukee Motor
• Electronic variable speed (10,000-22,000 rpm)
• Premium electronic feedback circuitry
• Exclusive Linear Depth Adjustment System with Above-the-Table Access

Features

• One-year warranty through the Dewalt factory or an authorized service center
• Factory reconditioned to perform like new! Limit 1 per order.
• 6.2 amp motor
• Helical-cut steel, heat-treated gears for smooth operation
• High torque for deck building and drywall

Reviews (1)

Good Product
Nicely balanced, plenty of power, and comfortable and a great price. If you are doing strictly drywall you may prefer the DW251R (0-4000 rpms) vrs the DW257R (0-2500 rpms). ... Read more

Features

• Unique three wheel design places the motor between the rollers for better balance
• Factory reconditioned to perform like new!
• 3" x 21" belt sander offers a powerful 8 amp motor
• Electronic feedback maintains belt speed from 850-to-1450 sfpm under load
• Only machined platen in the belt sander industry ensures flatness

Features

• Rockford Fosgate Sound System with Punch EQ
• Rugged construction withstands 8-foot drop to concrete
• Digital tuning with up to 20 presets
• 5-1/4" weather resistant speakers with separate tweeters

Features

• Includes two 1.2 Ah Batteries, 1-Hour Charger, No.2 Phillips 2" Driver Bit, Flashlight, 6pc. driver bit set and Plastic Case 22-stage slip-clutch for precision driving
• Flashlight included for illuminating the work
• Lightweight at only 5.3 pounds for easy drilling
• Heavy-duty high torque motor for optimal power
• Electronic feedback power control for high torque at lower rpm's

Reviews (3)

To Reviewer Below
In addition to not being able to read, I believe he maybe blind.There are no "blue tabs" on the photo.There is nothing but black and green.

Can you not read?
To the other reviewer, can't you read that it says "Includes two 1.2 Ah Batteries".Don't give the product a bad review b/c you can't read the specs.

BEWARE, not as pictured or advertised...
This is the DS18DVB drill. However the refurbished kit came with the EB1812 batteries, which are only 1.2Ah and the charger that came with it will only charge them, not the other 18v batteries Hitachi sells. The picture Amazon has with this item clearly shows the 2.0Ah batteries (you can tell by the blue tabs, the 3.0Ah are yellow and the 1.2Ah are all black) While it is a good drill and flashlight, I bought this kit at this price primarily to get a couple more batteries and a back-up charger. You are better off getting the kit new with the better batteries. Better still, get the kit that comes with the 3.0Ah batteries, a reciprocal saw and a circular saw. I will probably be making Amazon take this back. ... Read more

Features

• Flashlight included
• High performance motor
• 3/8" Key-less chuck
• 22 position clutch
• 2 speed transmission

Features

• Fastens a full bundle of shingles without reloading
• Drives standard .120 diameter, 15 degree wire collated roofing nails from 7/8" to 1-3/4"
• Powerful high performance motor with adjustable tool-free exhaust diffuser
• Features double cams and guides and quick adjust support for all nail lengths
• Steel contact safety with dual carbide inserts